相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Numerical simulation of S355JR-316L dissimilar metal welding
Bensheng Huang et al.
WELDING IN THE WORLD (2022)
COMPARISON OF FEM AND FVM FOR THE NUMERICAL SIMULATION OF FORGING PROCESS
Jan Rihacek et al.
MM SCIENCE JOURNAL (2020)
Heat source management in wire-arc additive manufacturing process for Al-Mg and Al-Si alloys
Kohei Oyama et al.
ADDITIVE MANUFACTURING (2019)
Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint
Dean Deng et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)
Numerical investigation of formation mechanism of welding residual stress in P92 steel multi-pass joints
Suo Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Influence of the welding sequence on residual stress and distortion of fillet welded structures
Guangming Fu et al.
MARINE STRUCTURES (2016)
Study on the microstructure, mechanical properties and corrosion behaviour of S355JR/316L dissimilar welded joint prepared by gas tungsten arc welding multi-pass welding process
B. -S. Huang et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2016)
Modelling the creation and destruction of columnar and equiaxed zones during solidification and melting in multi-pass welding of steel
G. Duggan et al.
COMPUTATIONAL MATERIALS SCIENCE (2015)
Simulation of laser butt welding of AISI 316L stainless steel sheet using various heat sources and experimental validation
Jazeel Rahman Chukkan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Microstructure and properties of Mg/Al joint welded by gas tungsten arc welding-assisted hybrid ultrasonic seam welding
Xiangyu Dai et al.
MATERIALS & DESIGN (2015)
Numerical simulation on the effect of welding parameters on welding residual stresses in T92/S30432 dissimilar welded pipe
Lei Zhao et al.
ADVANCES IN ENGINEERING SOFTWARE (2014)
Effect of boundary conditions on residual stress and distortion in T-joint welds
Guangming Fu et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2014)
Short-Term High-Temperature Tensile Tests and Prediction of Long-Term Strength of Welded Joints of Dissimilar Steels T92/HR3C
Y. M. Song et al.
METAL SCIENCE AND HEAT TREATMENT (2014)
Characterization of material properties and heat source parameters in welding simulation of two overlapping beads on a substrate plate
Suraj Joshi et al.
COMPUTATIONAL MATERIALS SCIENCE (2013)
Influence of deposition sequence on welding residual stress and deformation in an austenitic stainless steel J-groove welded joint
Dean Deng
MATERIALS & DESIGN (2013)
Methods of measuring residual stresses in components
N. S. Rossini et al.
MATERIALS & DESIGN (2012)
Effect of heat source configuration on the result quality of numerical calculation of welding-induced distortion
C. Heinze et al.
SIMULATION MODELLING PRACTICE AND THEORY (2012)
Determination of welding stress and distortion in discontinuous welding by means of numerical simulation and comparison with experimental measurements
Zhi Zeng et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
FEM prediction of welding residual stresses in a SUS304 girth-welded pipe with emphasis on stress distribution near weld start/end location
Dean Deng et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
Adaptive mesh technique for thermal-metallurgical numerical simulation of arc welding processes
M. Hamide et al.
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2008)
Effects of temperature-dependent material properties on welding simulation
XK Zhu et al.
COMPUTERS & STRUCTURES (2002)