☆ 4.7 Review

Use of industrial waste materials for 3D printing of sustainable concrete: A review

JOURNAL OF CLEANER PRODUCTION (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Construction & Building Technology

Effects of unconventional fly ashes on cementitious paste properties

Ying Wang et al.

Summary: This study evaluated the impacts of various unconventional fly ashes on the properties of cementitious paste, comparing them to traditional fly ashes and inert materials. Differences between Class C and Class F fly ashes were observed, with some properties positively correlated with CaO content. Unconventional fly ashes were found to be reactive and contribute to strength development without negatively affecting cement hydration. The results suggest a need to broaden fly ash specifications to include unconventional types.

CEMENT & CONCRETE COMPOSITES (2022)

添加到收藏夹

Article Construction & Building Technology

Digital fabrication of eco-friendly ultra-high performance fiber-reinforced concrete

Arun R. Arunothayan et al.

Summary: An eco-friendly 3DP-UHPFRC has been developed by replacing a high volume of cement component with fly ash and/or ground granulated blast furnace slag. These mixtures show significantly higher environmental sustainability while maintaining mechanical performance comparable to traditional 3DP-UHPFRC. A material efficiency index was proposed to compare the suitability of the eco-friendly mixtures, showing that mixtures with slag replacement have the highest index.

CEMENT & CONCRETE COMPOSITES (2022)

添加到收藏夹

Review Environmental Sciences

Alternative supplementary cementitious materials for sustainable concrete structures: a review on characterization and properties

J. Duchesne

Summary: One of the main priorities for a government is to achieve sustainable development through strategies to protect the global environment, enhance employee health and safety, reduce emissions, and responsibly use fuels and raw materials across all sectors of the economy. Blended Portland cements containing supplementary cementitious materials (SCMs) are excellent examples of industrial ecology, offering solutions to reduce environmental impacts in several industries. Through the use of SCMs in cement production, CO2 emissions can be reduced, non-renewable material sources can be saved, waste can be minimized, and the properties of concrete can be enhanced.

WASTE AND BIOMASS VALORIZATION (2021)

添加到收藏夹

Article Engineering, Civil

Influence of Waste Tire Rubber Particles Size on the Microstructural, Mechanical, and Acoustic Insulation Properties of 3D-Printable Cement Mortars

Matteo Sambucci et al.

Summary: 3D printing technologies in construction are becoming increasingly popular, aiming to reduce injuries and waste while enhancing flexibility in architectural design. A study on the relationship between rubber particle size and technological properties has been proposed for optimizing the performance of 3D printable mixes.

CIVIL ENGINEERING JOURNAL-TEHRAN (2021)

添加到收藏夹

Article Construction & Building Technology

Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content

Manu K. Mohan et al.

Summary: This study investigates the rheological behavior of 3D printable cementitious materials with different aggregate-to-binder ratios, analyzing the pumping and printing characteristics based on measured rheological parameters. The study found that increasing the ratio of aggregate-to-binder resulted in significant changes in plastic viscosity, yield stress, and storage modulus, providing insights into the behavior of high yield stress fluids during pumping and printing processes.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Mechanics

Flow-based pultrusion of continuous fi bers for cement-based composite material and additive manufacturing: rheological and technological requirements

Leo Demont et al.

Summary: The majority of extrusion-based concrete additive manufacturing focuses on unreinforced mortar, but the lack of reinforcement limits its industrial development. A new reinforcement method called flow-based pultrusion (FBP) is introduced in this paper, which uses continuous fiber rovings to increase the yield stress of the mortar and create anisotropic concrete.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

Printability and advantages of 3D printing mortar with 100% recycled sand

Shuai Zou et al.

Summary: By adding a suitable amount of sodium gluconate, the printability and green strength of printing mortar with 100% recycled sand can be improved, which is beneficial for the practical application of 3D concrete printing.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Environmental and economic assessment on 3D printed buildings with recycled concrete

Yilong Han et al.

Summary: This study evaluated the environmental impact and economic benefit of 3D printed buildings made of recycled concrete. It found that while 3D printing concrete construction has a larger environmental impact compared to traditional methods, it offers significant advantages in terms of cost efficiency, particularly for geometrically irregular buildings. Additionally, the cost of buildings made of recycled concrete decreases as the proportion of recycled aggregate increases.

JOURNAL OF CLEANER PRODUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

Digital design computing and modelling for 3-D concrete printing

Vuong Nguyen-Van et al.

Summary: A novel computational framework for 3D concrete printing process is proposed in this paper to capture layer-by-layer buildability and failure modes of complex structures. The framework is validated to predict printed outcomes accurately and reveal the buildability differences between different structures.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

Synchronized concrete and bonding agent deposition system for interlayer bond strength enhancement in 3D concrete printing

Yiwei Weng et al.

Summary: The proposed synchronized concrete and bonding agent deposition system addresses the weak interlayer bond strength issue in extrusion-based 3D concrete printing. By using cement paste as the bonding agent, a relative bond strength as high as 267% can be achieved through the system.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

A 3D concrete printing prefabrication platform for bespoke columns

Ana Anton et al.

Summary: This paper discusses the latest developments in digital concrete fabrication, specifically 3DCP, and its application in customized column production. The technology allows shaping concrete without formwork and placing material only where functionally required, thus optimizing material use. Additionally, the paper proposes a method for evaluating the geometric complexity of columns.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

Effect of alkali reactions on the rheology of one-part 3D printable geopolymer concrete

Shravan Muthukrishnan et al.

Summary: This study investigates the influence of early age activation reactions on the yield strength development of 3D printable geopolymer concrete, using a rheo-chemical approach. The results show that by selecting appropriate activator, thixotropic additive, and retarder content, the printability of concrete can be enhanced.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Construction & Building Technology

Vibration induced active rheology control for 3D concrete printing

J. G. Sanjayan et al.

Summary: Active rheology control using vibration can improve the rheological properties of concrete in 3D concrete printing, and enhance the mechanical properties of printed structures.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

Hardened properties and durability of large-scale 3D printed cement-based materials

Yu Zhang et al.

Summary: This study investigates the properties and void distribution of large-scale 3D printed cement-based materials. The results show that 3DPC has higher strength and better resistance to some degradation mechanisms, but lower resistance to others. Voids in 3DPC are strongly oriented along the printing direction and more interconnected, leading to anisotropy in material performance.

MATERIALS AND STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

Effect of printing parameters on material distribution in spray-based 3D concrete printing (S-3DCP)

Bing Lu et al.

Summary: The adoption of 3D concrete printing (3DCP) contributes to automation and efficiency in construction, and spray-based 3D concrete printing (S-3DCP) has been proposed for vertical and overhanging applications. Limited research studies on how printing parameters affect material distribution in S-3DCP have hindered its development. This study focuses on analyzing the effect of printing parameters and proposes an analytical model to guide parameter selection and enhance efficiency in construction.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

Fiber orientation effects on ultra-high performance concrete formed by 3D printing

Arun R. Arunothayan et al.

Summary: This study quantitatively investigated the orientation distribution of steel fibers in 3D printed ultra-high performance concrete, revealing that smaller nozzle size and higher fiber volume fraction significantly improved fiber alignment parallel to printing direction, resulting in superior mechanical performance of the printed specimens compared to mold-cast specimens.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

Experimental characterization of quaternary blended mortar exposed to marine environment using mechanical strength, corrosion resistance and chemical composition

Dodda Srinivas et al.

Summary: The study investigates the strength, durability, and corrosion resistance of quaternary blended mortar made with PPC, GGBS, and RHA in a marine environment. The optimized quaternary blended mortar exhibits improved mechanical strengths and enhanced resistance to chloride penetration, corrosion, and water absorption compared to the control mix after exposure to marine environment. Mineralogical and chemical analyses are conducted to determine the effects of marine environment exposure on the different mixes.

JOURNAL OF BUILDING ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

Influence of the printing direction and age on the mechanical properties of 3D printed concrete

Behzad Zahabizadeh et al.

Summary: 3D concrete printing (3DCP) technology developed through wet extrusion is a digitized approach aiming to enhance traditional construction methods. An experimental program was conducted to evaluate the mechanical/structural behavior of printed elements under different loading conditions, showing adequate quality of the printed specimens and minimal differences with the mould cast series in terms of physical properties.

MATERIALS AND STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

3D printing eco-friendly concrete containing under-utilised and waste solids as aggregates

Gang Bai et al.

Summary: 3D concrete printing technology provides an opportunity for utilising underutilised and waste solids as aggregates. The experimental study in this article shows that the self-supporting skeletal effect formed by gradated particles can improve the construction performance of mixtures and reduce the shrinkage of the cement matrix. These findings provide feasible solutions for promoting the eco-utilisation of underutilised and waste solids in 3D printing while meeting strength and durability requirements.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Construction & Building Technology

Construction and demolition waste-based geopolymers suited for use in 3-dimensional additive manufacturing

Oguzhan Sahin et al.

Summary: The paper evaluates the rheological properties of ambient-cured 100% construction and demolition waste (CDW)-based geopolymers for 3-dimensional additive manufacturing (3D-AM). The study shows that these geopolymers can be successfully used for 3D-printing at a laboratory scale with adequate rheological and mechanical properties without additional chemical admixtures. The empirical test methods used are effective in assessing the suitability of CDW-based geopolymers for 3D-AM applications.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Rheology and application of buoyant foam concrete for digital fabrication

Seung Cho et al.

Summary: This research improves the rheological performance of LWFC by adding nanopowder and calcium sulfoaluminate cement, increasing yield stress, improving thixotropic performance, viscosity, and elastic shear modulus evolution. The study also shows that foam volume significantly influences rheological properties and investigates shape retention and buildability through a buildability test. Additionally, a practical example of printing a lightweight fa?ade element with buoyant characteristics further demonstrates the potential application of 3D concrete printing.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

Stability of steel slag as fine aggregate and its application in 3D printing materials

Shuo Dai et al.

Summary: This study utilizes steel slag as fine aggregate to substitute natural sand in cement mortar synthesis, with the optimal content of SS determined to be 25%. Results from autoclave tests indicate that excessive SS content can lead to serious damage to mortar bars. XRD analysis and 3D printing experiments demonstrate the feasibility of using SS mortar in the field of 3D printing.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Durability assessment and microstructural analysis of 3D printed concrete exposed to sulfuric acid environments

Bilal Baz et al.

Summary: Experimental study compared 3D printed elements to casted ones in terms of mechanical and durability performance, finding no inter-layer cracking in printed elements and a strong overall specimen performance.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Flexural properties of 3D printed fibre-reinforced concrete with recycled sand

Tao Ding et al.

Summary: The study found that the addition of PE fibers can compensate for the negative impact of recycled sand on the flexural properties of 3D printed concrete specimens, significantly improving the flexural strength. Scanning electron microscopy results showed that the attachment of recycled sand can increase the porosity of the specimens.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Sustainability tradeoffs in the adoption of 3D Concrete Printing in the construction industry

Max Adaloudis et al.

Summary: 3D Concrete Printing (3DCP) is gaining attention as a solution to reduce carbon emissions from cement production, with companies motivated more by the potential for automation and addressing skill shortages in the construction sector than environmental benefits. Current government procurement rules do not sufficiently reward sustainability benefits to encourage the uptake of 3DCP.

JOURNAL OF CLEANER PRODUCTION (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Experimental measurement on the effects of recycled glass cullets as aggregates for construction 3D printing

Guan Heng Andrew Ting et al.

Summary: This study investigates the effects of recycled glass cullets as fine aggregates for construction 3D printing materials. The results show that as the content of recycled glass cullets increases, the rheological properties and mechanical properties of the material change accordingly.

JOURNAL OF CLEANER PRODUCTION (2021)

添加到收藏夹

Review Chemistry, Physical

3D Concrete Printing: A Systematic Review of Rheology, Mix Designs, Mechanical, Microstructural, and Durability Characteristics

Atta Ur Rehman et al.

Summary: This paper provides an up-to-date review of research on 3D concrete printing technology, focusing on rheological requirements and anisotropic behavior of mechanical properties of printed concrete. It evaluates strength performance along different axes and discusses methods for enhancing structural performance.

MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Mechanical enhancement for EMW-absorbing cementitious material using 3D concrete printing

Junbo Sun et al.

Summary: This study demonstrates the enhancement of mechanical capacity and electromagnetic wave absorption of concrete by optimizing chemical additives and printing parameters. 3D printing technology with enhancement methodology improves microwave absorption and reduces concrete porosity, increasing compressive strength.

JOURNAL OF BUILDING ENGINEERING (2021)

添加到收藏夹

Review Construction & Building Technology

Biomass ashes from agricultural wastes as supplementary cementitious materials or aggregate replacement in cement/geopolymer concrete: A comprehensive review

Blessen Skariah Thomas et al.

Summary: This comprehensive review examines recent trends in incorporating biomass ashes from agricultural waste in Ordinary Portland cement and geopolymer concrete, highlighting the potential to reduce carbon emissions and promote sustainable development. It confirms the feasibility of using biomass ashes as pozzolanic materials in cement concrete or as alternative activators in geopolymer concrete, contributing to building materials with the required properties.

JOURNAL OF BUILDING ENGINEERING (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

3D concrete printer parameter optimisation for high rate digital construction avoiding plastic collapse

Jacques Kruger et al.

COMPOSITES PART B-ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

A desorptivity-based approach for the assessment of phase separation during extrusion of cementitious materials

A. Rahul et al.

CEMENT & CONCRETE COMPOSITES (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

Investigation of the properties of alkali-activated slag mixes involving the use of nanoclay and nucleation seeds for 3D printing

Biranchi Panda et al.

COMPOSITES PART B-ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Real-time quantification of fresh and hardened mechanical property for 3D printing material by intellectualization with piezoelectric transducers

Guowei Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Yield stress criteria to assess the buildability of 3D concrete printing

R. Jayathilakage et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

Mechanical Behavior of Printed Strain Hardening Cementitious Composites

Stefan Chaves Figueiredo et al.

MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Mechanical behavior of 3D printed mortar with recycled sand at early ages

Tao Ding et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Preparation and microstructural characterization of a novel 3D printable building material composed of copper tailings and iron tailings

Xinjian Li et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Influence of multi-walled nanotubes on the fresh and hardened properties of a 3D printing PVA mortar ink

Xiaoyan Sun et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Steel fibres reinforced 3D printed concrete: Influence of fibre sizes on mechanical performance

Luong Pham et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Setting on demand for digital concrete - Principles, measurements, chemistry, validation

Lex Reiter et al.

CEMENT AND CONCRETE RESEARCH (2020)

添加到收藏夹

Article Green & Sustainable Science & Technology

Study of MgO-activated slag as a cementless material for sustainable spray-based 3D printing

Bing Lu et al.

JOURNAL OF CLEANER PRODUCTION (2020)

添加到收藏夹

Article Green & Sustainable Science & Technology

Comparative economic, environmental and productivity assessment of a concrete bathroom unit fabricated through 3D printing and a precast approach

Yiwei Weng et al.

JOURNAL OF CLEANER PRODUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

Fresh Properties of Cementitious Materials Containing Rice Husk Ash for Construction 3D Printing

Shravan Muthukrishnan et al.

JOURNAL OF MATERIALS IN CIVIL ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Inspecting manufacturing precision of 3D printed concrete parts based on geometric dimensioning and tolerancing

Jie Xu et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

A critical examination of the influence of material characteristics and extruder geometry on 3D printing of cementitious binders

Sooraj A. O. Nair et al.

CEMENT & CONCRETE COMPOSITES (2020)

添加到收藏夹

Article Construction & Building Technology

Comparison of the effects that supplementary cementitious materials replacement levels have on cementitious paste properties

Sivakumar Ramanathan et al.

CEMENT & CONCRETE COMPOSITES (2020)

添加到收藏夹

Article Construction & Building Technology

Hardened properties of layered 3D printed concrete with recycled sand

Tao Ding et al.

CEMENT & CONCRETE COMPOSITES (2020)

添加到收藏夹

Article Construction & Building Technology

Development of 3D-printable ultra-high performance fiber-reinforced concrete for digital construction

Arun R. Arunothayan et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

A rheology-based quasi-static shape retention model for digitally fabricated concrete

Jacques Kruger et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Green & Sustainable Science & Technology

Environmental assessment of large-scale 3D printing in construction: A comparative study between cob and concrete

Hashem Alhumayani et al.

JOURNAL OF CLEANER PRODUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

Bond properties of reinforcing bar penetrations in 3D concrete printing

Taylor Marchment et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

Layer-interface properties in 3D printed concrete: Dual hierarchical structure and micromechanical characterization

Zifan Geng et al.

CEMENT AND CONCRETE RESEARCH (2020)

添加到收藏夹

Article Construction & Building Technology

Effect of microwave heating on interlayer bonding and buildability of geopolymer 3D concrete printing

Shravan Muthukrishnan et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

3D Concrete Printing Sustainability: A Comparative Life Cycle Assessment of Four Construction Method Scenarios

Malek Mohammad et al.

BUILDINGS (2020)

添加到收藏夹

Article Construction & Building Technology

Examining the significance of infill printing pattern on the anisotropy of 3D printed concrete

Daniel Heras Murcia et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

3D recycled mortar printing: System development, process design, material properties and on-site printing

Jianzhuang Xiao et al.

JOURNAL OF BUILDING ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Properties of a double-layer EMW-absorbing structure containing a graded nano-sized absorbent combing extruded and sprayed 3D printing

Junbo Sun et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Electromagnetic wave absorbing performance of 3D printed wave-shape copper solid cementitious element

Junbo Sun et al.

CEMENT & CONCRETE COMPOSITES (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

Plastic shrinkage cracking in 3D printed concrete

Gerrit M. Moelich et al.

COMPOSITES PART B-ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Inline quantification of extrudability of cementitious materials for digital construction

V. N. Nerella et al.

CEMENT & CONCRETE COMPOSITES (2019)

添加到收藏夹

Article Construction & Building Technology

3D printable concrete: Mixture design and test methods

A. V. Rahul et al.

CEMENT & CONCRETE COMPOSITES (2019)

添加到收藏夹

Article Construction & Building Technology

Mixture Design Approach to optimize the rheological properties of the material used in 3D cementitious material printing

Zhixin Liu et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Environmental Sciences

Utilization of recycled glass for 3D concrete printing: rheological and mechanical properties

Guan Heng Andrew Ting et al.

JOURNAL OF MATERIAL CYCLES AND WASTE MANAGEMENT (2019)

添加到收藏夹

Article Construction & Building Technology

Direct shear test for the assessment of rheological parameters of concrete for 3D printing applications

Roshan Jayathilakage et al.

MATERIALS AND STRUCTURES (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Rheological behavior of high volume fly ash mixtures containing micro silica for digital construction application

Biranchi Panda et al.

MATERIALS LETTERS (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay

Biranchi Panda et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Mechanical properties and deformation behaviour of early age concrete in the context of digital construction

Biranchi Panda et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Article Construction & Building Technology

Experimental methods to determine the feasibility of steel slags as supplementary cementitious materials

Ying Wang et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

Comparative sustainability assessment of binary blended concretes using Supplementary Cementitious Materials (SCMs) and Ordinary Portland Cement (OPC)

Kamel Mohamed Rahla et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

Synthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing

Biranchi Panda et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Construction & Building Technology

Designing spray-based 3D printable cementitious materials with fly ash cenosphere and air entraining agent

Bing Lu et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Chemistry, Physical

The Effect of Material Fresh Properties and Process Parameters on Buildability and Interlayer Adhesion of 3D Printed Concrete

Biranchi Panda et al.

MATERIALS (2019)

添加到收藏夹

Article Construction & Building Technology

Extending supplementary cementitious material resources: Reclaimed and remediated fly ash and natural pozzolans

Ivan Diaz-Loya et al.

CEMENT & CONCRETE COMPOSITES (2019)

添加到收藏夹

Article Construction & Building Technology

3D concrete printing: A lower bound analytical model for buildability performance quantification

Jacques Kruger et al.

AUTOMATION IN CONSTRUCTION (2019)

添加到收藏夹

Article Construction & Building Technology

New insights from reactivity testing of supplementary cementitious materials

Prannoy Suraneni et al.

CEMENT & CONCRETE COMPOSITES (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Extrusion and rheology characterization of geopolymer nanocomposites used in 3D printing

Biranchi Panda et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Article Construction & Building Technology

Feasibility study on sustainable magnesium potassium phosphate cement paste for 3D printing

Yiwei Weng et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Construction & Building Technology

An ab initio approach for thixotropy characterisation of (nanoparticle-infused) 3D printable concrete

Jacques Kruger et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Chemistry, Physical

Microstructural Characterization of 3D Printed Cementitious Materials

Jolien Van Der Putten et al.

MATERIALS (2019)

添加到收藏夹

Article Construction & Building Technology

Strain-based approach for measuring structural build-up of cement pastes in the context of digital construction

V. N. Nerella et al.

CEMENT AND CONCRETE RESEARCH (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

Rheology and buildability of sustainable cement-based composites containing micro-crystalline cellulose for 3D-printing

Wu-Jian Long et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Engineering, Manufacturing

Printability and fire performance of a developed 3D printable fibre reinforced cementitious composites under elevated temperatures

Yiwei Weng et al.

VIRTUAL AND PHYSICAL PROTOTYPING (2019)

添加到收藏夹

Article Engineering, Civil

Properties of cement grout modified with ultra-fine slag

Sowmini Gopinathan et al.

FRONTIERS OF STRUCTURAL AND CIVIL ENGINEERING (2018)

添加到收藏夹

Article Engineering, Civil

Fresh and hardened properties of 3D printable cementitious materials for building and construction

Suvash Chandra Paul et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2018)

添加到收藏夹

Article Construction & Building Technology

A self-reinforced cementitious composite for building-scale 3D printing

Daniel G. Soltan et al.

CEMENT & CONCRETE COMPOSITES (2018)

添加到收藏夹

Article Construction & Building Technology

The role of early age structural build-up in digital fabrication with concrete

Lex Reiter et al.

CEMENT AND CONCRETE RESEARCH (2018)

添加到收藏夹

Article Construction & Building Technology

Eco-efficient cements: Potential economically viable solutions for a low-CO2 cement-based materials industry

Karen L. Scrivener et al.

CEMENT AND CONCRETE RESEARCH (2018)

添加到收藏夹

Article Materials Science, Ceramics

Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concrete printing

Biranchi Panda et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Construction & Building Technology

Fresh properties of a novel 3D printing concrete ink

Yu Zhang et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Improving flexural characteristics of 3D printed geopolymer composites with in-process steel cable reinforcement

Jian Hui Lim et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Effect of mineral admixtures on the structural build-up of cement paste

Qiang Yuan et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Printable properties of cementitious material containing copper tailings for extrusion based 3D printing

Guowei Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

3D-printed steel reinforcement for digital concrete construction - Manufacture, mechanical properties and bond behaviour

Viktor Mechtcherine et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Design 3D printing cementitious materials via Fuller Thompson theory and Marson-Percy model

Yiwei Weng et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Engineering, Multidisciplinary

Measurement of tensile bond strength of 3D printed geopolymer mortar

Biranchi Panda et al.

MEASUREMENT (2018)

添加到收藏夹

Article Construction & Building Technology

Method for the Enhancement of Buildability and Bending Resistance of 3D Printable Tailing Mortar

Zhijian Li et al.

INTERNATIONAL JOURNAL OF CONCRETE STRUCTURES AND MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Electromagnetic and microwave absorbing properties of cementitious composite for 3D printing containing waste copper solids

Guowei Ma et al.

CEMENT & CONCRETE COMPOSITES (2018)

添加到收藏夹

Article Construction & Building Technology

Empirical models to predict rheological properties of fiber reinforced cementitious composites for 3D printing

Yiwei Weng et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Field trials with concrete incorporating biomass-fly ash

Ahmed Omran et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing

Biranchi Panda et al.

CEMENT & CONCRETE COMPOSITES (2018)

添加到收藏夹

Article Construction & Building Technology

Characterization of supplementary cementitious materials by thermal analysis

Susan A. Bernal et al.

MATERIALS AND STRUCTURES (2017)

添加到收藏夹

Article Green & Sustainable Science & Technology

Environmental design guidelines for digital fabrication

Isolda Agusti-Juan et al.

JOURNAL OF CLEANER PRODUCTION (2017)

添加到收藏夹

Article Green & Sustainable Science & Technology

Additive manufacturing of geopolymer for sustainable built environment

Biranchi Panda et al.

JOURNAL OF CLEANER PRODUCTION (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material

Biranchi Panda et al.

MATERIALS LETTERS (2017)

添加到收藏夹

Editorial Material Chemistry, Physical

Towards sustainable concrete

Paulo J. M. Monteiro et al.

NATURE MATERIALS (2017)

添加到收藏夹

Article Construction & Building Technology

Cementitious materials for construction-scale 3D printing: Laboratory testing of fresh printing mixture

Ali Kazemian et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

添加到收藏夹

Article Engineering, Multidisciplinary

Experimental study on flexural behaviour of inorganic polymer concrete beams reinforced with basalt rebar

Xiaochun Fan et al.

COMPOSITES PART B-ENGINEERING (2016)

添加到收藏夹

Article Environmental Sciences

Readily implementable techniques can cut annual CO2 emissions from the production of concrete by over 20%

Sabbie A. Miller et al.

ENVIRONMENTAL RESEARCH LETTERS (2016)

添加到收藏夹

Article Construction & Building Technology

Recent advances in understanding the role of supplementary cementitious materials in concrete

Maria C. G. Juenger et al.

CEMENT AND CONCRETE RESEARCH (2015)

添加到收藏夹

Article Materials Science, Ceramics

Understanding the Filler Effect on the Nucleation and Growth of C-S-H

E. Berodier et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

添加到收藏夹

Article Materials Science, Ceramics

The Filler Effect: The Influence of Filler Content and Surface Area on Cementitious Reaction Rates

Tandre Oey et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2013)

添加到收藏夹

Article Construction & Building Technology

Hardened properties of high-performance printing concrete

T. T. Le et al.

CEMENT AND CONCRETE RESEARCH (2012)

添加到收藏夹

Article Construction & Building Technology

The influence of small particle on the fluidity of blast furnace slag cement paste containing superplasticizers

Stefania Grzeszczyk et al.

CONSTRUCTION AND BUILDING MATERIALS (2012)

添加到收藏夹

Article Construction & Building Technology

Mix design and fresh properties for high-performance printing concrete

T. T. Le et al.

MATERIALS AND STRUCTURES (2012)

添加到收藏夹

Article Construction & Building Technology

Supplementary cementitious materials

Barbara Lothenbach et al.

CEMENT AND CONCRETE RESEARCH (2011)

添加到收藏夹

Article Construction & Building Technology

Comprehensive phase characterization of crystalline and amorphous phases of a Class F fly ash

Ryan T. Chancey et al.

CEMENT AND CONCRETE RESEARCH (2010)

添加到收藏夹

Article Engineering, Environmental

Chloride chemical form in various types of fly ash

Fenfen Zhu et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2008)

添加到收藏夹

Article Construction & Building Technology

Alkali release characteristics of blended cements

MH Shehata et al.

CEMENT AND CONCRETE RESEARCH (2006)

添加到收藏夹

Article Construction & Building Technology

Automated construction by contour crafting - related robotics and information technologies

B Khoshnevis

AUTOMATION IN CONSTRUCTION (2004)

添加到收藏夹

Article Construction & Building Technology

Effect of silica fume on mechanical properties of high-strength concrete

M Mazloom et al.

CEMENT & CONCRETE COMPOSITES (2004)

添加到收藏夹

Article Construction & Building Technology

Limestone filler cement in low w/c concrete:: A rational use of energy

V Bonavetti et al.

CEMENT AND CONCRETE RESEARCH (2003)

添加到收藏夹

Article Construction & Building Technology

A new way to increase the long-term bond strength of new-to-old concrete by the use of fly ash

GY Li

CEMENT AND CONCRETE RESEARCH (2003)

添加到收藏夹

Article Construction & Building Technology

The influence of mineral admixtures on the theology of cement paste and concrete

CF Ferraris et al.

CEMENT AND CONCRETE RESEARCH (2001)

添加到收藏夹

Article Construction & Building Technology

The effect of fly ash composition on the expansion of concrete due to alkali-silica reaction

MH Shehata et al.

CEMENT AND CONCRETE RESEARCH (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.