☆ 4.7 Article

Ultrasonic Lamb wave mixing based fatigue crack detection using a deep learning model and higher-order spectral analysis

INTERNATIONAL JOURNAL OF FATIGUE (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Detection and localization of fatigue crack using nonlinear ultrasonic three-wave mixing technique

Santhakumar Sampath et al.

Summary: A nonlinear ultrasonic three-wave mixing technique was developed in this study to accurately detect and localize early-stage fatigue cracks. The effectiveness of the proposed technique was validated through experiments with aluminum specimens, and it was found to have higher sensitivity towards fatigue cracks compared to conventional nonlinear ultrasonic techniques.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Article Automation & Control Systems

A novel based-performance degradation indicator RUL prediction model and its application in rolling bearing

Chuangyan Yang et al.

Summary: This study proposes a novel RUL prediction model based on performance degradation indicators to address the poor prediction performance of rolling bearing remaining useful life (RUL) with a single degradation indicator. The vibration signal of the rolling bearing is decomposed, and the degradation feature set of the reconstructed signals is extracted. The sensitive degradation indicator is calculated by fusing improved independent component analysis and Mahalanobis Distance, and the error fluctuations are repaired using a gray regression model. Finally, a neural network model based on the health indicator is constructed to predict the RUL of the rolling bearing.

ISA TRANSACTIONS (2022)

添加到收藏夹

Review Engineering, Mechanical

A review of fatigue damage detection and measurement techniques

Fredrik Bjorheim et al.

Summary: This paper reviews the existing techniques for fatigue damage detection and measurement, focusing on fatigue crack monitoring and fatigue damage monitoring. Parameters of these techniques are critically evaluated for choosing the suitable method for detecting fatigue crack or damage in materials or components.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Article Engineering, Mechanical

Fatigue crack initiation behaviors around defects induced by welding thermal cycle in superalloy IN617B

Shanlin Li et al.

Summary: In this study, fatigue crack initiation behaviors around defects induced by welding thermal cycle in IN617B were investigated. Two mechanisms of fatigue crack initiation were clarified, and the dominant mechanism was determined by the distance of crack initiation from defects. Welding defects altered the deformation mode of the near-field region, accelerating the fatigue failure process.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Article Computer Science, Hardware & Architecture

Smart communication using tri-spectral sign recognition for hearing-impaired people

B. Kanisha et al.

Summary: Recent technological advancements have enabled individuals with hearing impairment and speech loss to interact more intelligently and effectively with others. By utilizing tools that convert speech to sign language and sign to speech, these individuals are able to use smartphones and engage in remote communication more easily.

JOURNAL OF SUPERCOMPUTING (2022)

添加到收藏夹

Article Acoustics

Cubic nonlinearity parameter measurement and material degradation detection using nonlinear ultrasonic three-wave mixing

Santhakumar Sampath et al.

Summary: Early detection of accumulated damage or material degradation in structures is important. This study develops a nonlinear ultrasonic three wave mixing technique to generate and measure third-order combined harmonics (TOCH) in plate-like structures and to measure cubic nonlinearity parameter. The experimental results indicate that the proposed technique is more sensitive to early-stage material degradation.

ULTRASONICS (2022)

添加到收藏夹

Article Automation & Control Systems

Remaining useful life prediction techniques for electric valves based on convolution auto encoder and long short term memory

Hang Wang et al.

Summary: This study proposes a method for predicting the remaining useful life of electric valves by combining CAE and LSTM technologies, comparing network structures and hyperparameters to obtain a more suitable model, and testing the accuracy of the method to enhance the safety and economic operation of nuclear plants and other complex systems.

ISA TRANSACTIONS (2021)

添加到收藏夹

Article Construction & Building Technology

A deep learning-based approach for refined crack evaluation from shield tunnel lining images

Shuai Zhao et al.

Summary: This paper presents a deep learning-based approach that extends the PANet model by adding a semantic branch to refine crack evaluation and reduce inaccuracies associated with crack discontinuities and image skeletonization. Experimental results show that the proposed approach outperforms other methods, demonstrating its superiority in mitigating crack disjoint problems and skeletonization error. The evaluation metrics indicate that the proposed model is an alternative approach for crack segmentation and quantification in the field.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Review Construction & Building Technology

Machine vision-based surface crack analysis for transportation infrastructure

Wenbo Hu et al.

Summary: This study systematically evaluates machine vision-based surface crack analysis methods and describes the strengths and limitations of different solutions. An assessment of the application of deep learning in crack analysis, including image classification, object detection, pixel segmentation, geometric scale quantification, and growth prediction. The summary of challenges and breakthrough directions drives further development of deep learning to assist more sophisticated maintenance decisions.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Physics, Applied

Nonlinear ultrasonic guided waves-Principles for nondestructive evaluation

Cliff J. Lissenden

Summary: Research on the use of nonlinear ultrasonic guided waves for nondestructive evaluation is rapidly expanding due to their potential benefits for early detection of material degradation. The development of inspection strategies is complicated by the complexity of physical principles, limited effective solutions, and the challenging measurement of weak nonlinearity. The Tutorial focuses on the physical principles of nonlinear ultrasonic guided waves, internal resonance conditions, and applications in detecting material degradation, with a new result on energy transfer simulation presented.

JOURNAL OF APPLIED PHYSICS (2021)

添加到收藏夹

Article Engineering, Mechanical

A novel method of multiaxial fatigue life prediction based on deep learning

Jingye Yang et al.

Summary: A novel deep learning-based method is proposed in this study to predict fatigue data of different materials, with excellent prediction accuracy for various loading conditions. The method shows strong capability in handling different loading paths and levels, but its extrapolation capability may weaken with increasing distinctions between training and test datasets in terms of loading paths.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

添加到收藏夹

Article Construction & Building Technology

Detection of concealed cracks from ground penetrating radar images based on deep learning algorithm

Shuwei Li et al.

Summary: This study introduces an effective method utilizing 3-D ground penetrating radar (GPR) and deep learning models to automatically detect concealed cracks in asphalt pavement. The results demonstrate the feasibility of the proposed method, with YOLOv4 and YOLOv5 models showing significant advancements in crack detection even with a small dataset.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Thermodynamics

Short-term wind speed forecasting using recurrent neural networks with error correction

Jikai Duan et al.

Summary: This study presents a novel hybrid forecasting system that significantly enhances the accuracy of wind speed prediction, achieving superior prediction results compared to other models through a process of decomposition, prediction, and error correction.

ENERGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Evaluation of material degradation using phased array ultrasonic technique with full matrix capture

Santhakumar Sampath et al.

Summary: This paper introduces a new method using PAUT with FMC to measure acoustic properties and evaluate material degradation. Experimental results show that this method is more accurate than the conventional CUT technique, making it suitable for assessing material degradation.

ENGINEERING FAILURE ANALYSIS (2021)

添加到收藏夹

Article Computer Science, Information Systems

A data-driven structural damage detection framework based on parallel convolutional neural network and bidirectional gated recurrent unit

Jianxi Yang et al.

Summary: This paper proposes a novel end-to-end structural damage detection neural model, utilizing the advantages of Convolutional Neural Network and Bidirectional Gated Recurrent Unit in parallel to achieve better detection effect than existing methods.

INFORMATION SCIENCES (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

A fault frequency bands location method based on improved fast spectral correlation to extract fault features in axial piston pump bearings

Chaoang Xiao et al.

Summary: This paper proposes a fault frequency bands location method based on the Fast-SC algorithm, utilizing the new KESE indicator for fault frequency bands location and SEES for feature frequency extraction and fault type identification. Experimental results validate the superiority and efficiency of this method.

MEASUREMENT (2021)

添加到收藏夹

Article Acoustics

Sim-to-Real: Employing ultrasonic guided wave digital surrogates and transfer learning for damage visualization

K. Supreet Alguri et al.

Summary: Wavefield imaging is a powerful visualization tool in nondestructive evaluation for studying ultrasonic wave propagation and damage interactions. This paper discusses a flexible approach based on numerical simulations and transfer learning to isolate damage wavefields without the need for explicit experimental baselines. The effectiveness of this method is demonstrated through two setups in isolating damage reflections.

ULTRASONICS (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Sequence-based modeling of deep learning with LSTM and GRU networks for structural damage detection of floating offshore wind turbine blades

Do-Eun Choe et al.

Summary: This paper presents a sequence-based deep learning model for structural damage detection in floating offshore wind turbine blades. The neural networks trained on simulated sensor data achieved up to 94.8% accuracy in detecting damage presence and location. The cross-validation accuracy of the selected network was estimated to be 91.7%. Structural damage detection using deep learning is not limited by system assumptions or environmental conditions, offering a promising approach for improving structure safety.

RENEWABLE ENERGY (2021)

添加到收藏夹

Proceedings Paper Engineering, Aerospace

Detection of material nonlinearity using nonlinear ultrasonic three-wave mixing technique

Santhakumar Sampath et al.

Summary: This paper presents a new nonlinear ultrasonic technique based on three-wave mixing to detect material nonlinearity by measuring third-order combined harmonics (TOCH). Experimental results show that when phase matching and non-zero power flux conditions are met, the amplitude of TOCH increases steeply with propagation distance.

NONDESTRUCTIVE CHARACTERIZATION AND MONITORING OF ADVANCED MATERIALS, AEROSPACE, CIVIL INFRASTRUCTURE, AND TRANSPORTATION XV (2021)

添加到收藏夹

Article Physics, Multidisciplinary

Micro-crack detection of nonlinear Lamb wave propagation in three-dimensional plates with mixed-frequency excitation

Wei-Guang Zhu et al.

CHINESE PHYSICS B (2020)

添加到收藏夹

Article Automation & Control Systems

A novel bearing intelligent fault diagnosis framework under time-varying working conditions using recurrent neural network

Zenghui An et al.

ISA TRANSACTIONS (2020)

添加到收藏夹

Article Engineering, Civil

Increasing the robustness of material-specific deep learning models for crack detection across different materials

Mohamad Alipour et al.

ENGINEERING STRUCTURES (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

An enhanced modulation signal bispectrum analysis for bearing fault detection based on non-Gaussian noise suppression

Junchao Guo et al.

MEASUREMENT (2020)

添加到收藏夹

Article Construction & Building Technology

Deep convolution neural network-based transfer learning method for civil infrastructure crack detection

Qiaoning Yang et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Engineering, Geological

Digital spatial cracking behaviors of fine-grained sandstone with precracks under uniaxial compression

Xiao-Ping Zhou et al.

INTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS (2020)

添加到收藏夹

Article Automation & Control Systems

LSTM networks based on attention ordered neurons for gear remaining life prediction

Sheng Xiang et al.

ISA TRANSACTIONS (2020)

添加到收藏夹

Article Engineering, Aerospace

Numerical and Experimental Investigation of Nonlinear Lamb Wave Mixing at Low Frequency

Mohammed Aslam et al.

JOURNAL OF AEROSPACE ENGINEERING (2020)

添加到收藏夹

Article Engineering, Electrical & Electronic

Detecting the Early Damages in Structures With Nonlinear Output Frequency Response Functions and the CNN-LSTM Model

Baoxuan Zhao et al.

IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT (2020)

添加到收藏夹

Article Construction & Building Technology

A spatial-channel hierarchical deep learning network for pixel-level automated crack detection

Yue Pan et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Engineering, Mechanical

A multi-fidelity modelling approach to the statistical inference of the equivalent initial flaw size distribution for multiple-site damage

Llewellyn Morse et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Engineering, Mechanical

Characterization of a 3DOF aeroelastic system with freeplay and aerodynamic nonlinearities - Part I: Higher-order spectra

Michael Candon et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

添加到收藏夹

Article Instruments & Instrumentation

Mixed third harmonic shear horizontal wave generation: interaction between primary shear horizontal wave and second harmonic Lamb wave

Shengbo Shan et al.

SMART MATERIALS AND STRUCTURES (2019)

添加到收藏夹

Article Acoustics

New nonlinear ultrasonic method for material characterization: Codirectional shear horizontal guided wave mixing in plate

Shengbo Shan et al.

ULTRASONICS (2019)

添加到收藏夹

Article Engineering, Geological

Digital measurement of 2D and 3D cracks in sandstones through improved pseudo color image enhancement and 3D reconstruction method

Zhi Zhao et al.

INTERNATIONAL JOURNAL FOR NUMERICAL AND ANALYTICAL METHODS IN GEOMECHANICS (2019)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Multivariate LSTM-FCNs for time series classification

Fazle Karim et al.

NEURAL NETWORKS (2019)

添加到收藏夹

Article Multidisciplinary Sciences

Unsupervised Pre-training of a Deep LSTM-based Stacked Autoencoder for Multivariate Time Series Forecasting Problems

Alaa Sagheer et al.

SCIENTIFIC REPORTS (2019)

添加到收藏夹

Article Engineering, Mechanical

Nonlinear ultrasonic modulation based failure warning for aluminum plates subject to fatigue loading

Yongtak Kim et al.

INTERNATIONAL JOURNAL OF FATIGUE (2018)

添加到收藏夹

Article Materials Science, Characterization & Testing

Nonlinear Lamb wave mixing for assessing localized deformation during creep

Avijit Kr Metya et al.

NDT & E INTERNATIONAL (2018)

添加到收藏夹

Article Chemistry, Physical

Experimental and Numerical Study of Nonlinear Lamb Waves of a Low-Frequency S0 Mode in Plates with Quadratic Nonlinearity

Xiangyan Ding et al.

MATERIALS (2018)

添加到收藏夹

Article Acoustics

Nonlinear spectral correlation for fatigue crack detection under noisy environments

Peipei Liu et al.

JOURNAL OF SOUND AND VIBRATION (2017)

添加到收藏夹

Article Materials Science, Characterization & Testing

Nonlinear Lamb wave-mixing technique for micro-crack detection in plates

Jiao Jingpin et al.

NDT & E INTERNATIONAL (2017)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Higher order spectral regression discriminant analysis (HOSRDA): A tensor feature reduction method for ERP detection

Mina Jamshidi Idaji et al.

PATTERN RECOGNITION (2017)

添加到收藏夹

Article Engineering, Aerospace

Identification of freeplay and aerodynamic nonlinearities in a 2D aerofoil system with via higher-order spectra

M. Candon et al.

AERONAUTICAL JOURNAL (2017)

添加到收藏夹

Article Engineering, Mechanical

Bearing Fault Diagnosis Method Based on Local Mean Decomposition and Wigner Higher Moment Spectrum

J-H. Cai et al.

EXPERIMENTAL TECHNIQUES (2016)

添加到收藏夹

Article Instruments & Instrumentation

Baseline-free fatigue crack detection based on spectral correlation and nonlinear wave modulation

Peipei Liu et al.

SMART MATERIALS AND STRUCTURES (2016)

添加到收藏夹

Article Materials Science, Characterization & Testing

Evaluation of the intergranular corrosion in austenitic stainless steel using collinear wave mixing method

Jiao Jingpin et al.

NDT & E INTERNATIONAL (2015)

添加到收藏夹

Article Acoustics

Relationship between second- and third-order acoustic nonlinear parameters in relative measurement

Gang Ren et al.

ULTRASONICS (2015)

添加到收藏夹

Proceedings Paper Physics, Applied

Nonlinear guided wave mixing for localized material state characterization

Cliff J. Lissenden et al.

PROCEEDINGS OF THE 2015 ICU INTERNATIONAL CONGRESS ON ULTRASONICS (2015)

添加到收藏夹

Article Automation & Control Systems

Spectral analysis of block structured nonlinear systems and higher order sinusoidal input describing functions

David Rijlaarsdam et al.

AUTOMATICA (2011)

添加到收藏夹

Article Acoustics

Baseline-free estimation of residual fatigue life using a third order acoustic nonlinear parameter

Mikael Amura et al.

JOURNAL OF THE ACOUSTICAL SOCIETY OF AMERICA (2011)

添加到收藏夹

Article Materials Science, Characterization & Testing

Factors affecting the ultrasonic intermodulation crack detection technique using bispectral analysis

Charles R. P. Courtney et al.

NDT & E INTERNATIONAL (2008)

添加到收藏夹

Article Engineering, Multidisciplinary

Higher order spectra for crack and misalignment identification in the shaft of a rotating machine

Jyoti K. Sinha

STRUCTURAL HEALTH MONITORING-AN INTERNATIONAL JOURNAL (2007)

添加到收藏夹

Article Engineering, Mechanical

Quantification of fatigue damage accumulation using non-linear ultrasound measurements

Ramkumar K. Oruganti et al.

INTERNATIONAL JOURNAL OF FATIGUE (2007)

添加到收藏夹

Article Engineering, Mechanical

Effectiveness and sensitivity of vibration processing techniques for local fault detection in gears

G Dalpiaz et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.