☆ 4.7 Article

Mode II fracture of wood: Comparison between End-Notched Flexure and Compact Shear testing

ENGINEERING FRACTURE MECHANICS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Mechanics

Mode I and II R-curves characterization of the Maritime Pine and Spruce under the same geometry

Edouard Sorin et al.

Summary: This study provides detailed data on the quasi-brittle behavior of maritime pine and spruce using R-curves. The method used in this study for R-curve characterization is an improved version of the method presented by Lespine (2007), which is automated and based on measurement errors. The study investigates the influence of crack plane orientation and density on fracture mechanisms and highlights the differences between spruce and maritime pine.

ENGINEERING FRACTURE MECHANICS (2022)

添加到收藏夹

Article Engineering, Civil

Modeling approach to estimate the bending strength and failure mechanisms of laminated timber beams

Christoffer Vida et al.

Summary: The numerical simulation of four-point bending tests on glued laminated timber (GLT) beams requires an adequate description of the material behavior and relevant failure mechanisms. This paper proposes a modeling approach to reliably estimate the bending strength and failure mechanisms of GLT beams, which is validated by simulating experimentally tested GLT beams. The results show the importance of considering discrete cracks and the variability of knot geometries in accurately simulating the failure mechanisms of GLT beams.

ENGINEERING STRUCTURES (2022)

添加到收藏夹

Article Thermodynamics

An experimental analysis of the end-notched flexure composite laminates beams with elastic couplings

Jakub Rzeczkowski

Summary: This experimental study focused on the behavior of composite beams with elastic couplings in the end-notched flexure test, testing carbon/epoxy laminates with specific stacking sequences and different delamination interfaces. The results revealed that elastic couplings influenced intense bridging phenomena and contributed to a more extensive fracture process zone and mode III in total delamination resistance. The standardized ENF procedure can still be applied to determine the fracture toughness of laminates with elastic couplings, with the assistance of additional data reduction schemes and techniques or numerical analysis.

CONTINUUM MECHANICS AND THERMODYNAMICS (2021)

添加到收藏夹

Article Mechanics

Mode II critical stress intensity factor of solid wood obtained from the asymmetric four-point bend fracture test using groove-free and side-grooved samples

Hiroshi Yoshihara et al.

Summary: The Mode II fracture critical stress intensity factor (K-IIc) values obtained from the asymmetric four-point bend fracture (AFPBF) tests and three-point bend end-notched flexure (3ENF) tests on western hemlock samples showed significant differences, which were effectively reduced by introducing an additional crack length Delta into the data reduction process. This indicates that the K-IIc value can be accurately determined by considering the Delta value and results from previous Mode II fracture mechanics tests.

ENGINEERING FRACTURE MECHANICS (2021)

添加到收藏夹

Article Chemistry, Physical

Experimental Evaluation of Mode II fracture Properties of Eucalyptus globulus L.

Almudena Majano-Majano et al.

MATERIALS (2020)

添加到收藏夹

Article Engineering, Civil

Design model for the bending resistance of fibre reinforced glulam

Lukas Blank et al.

ENGINEERING STRUCTURES (2020)

添加到收藏夹

Article Construction & Building Technology

Experimental and numerical study on bending properties of heterogeneous lamella layups in cross laminated timber using Australian Radiata Pine

Xin Li et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Mechanics

Examination of the block shear fracture test method to measure the Mode-II critical stress intensity factor

Hiroshi Yoshihara et al.

ENGINEERING FRACTURE MECHANICS (2020)

添加到收藏夹

Article Construction & Building Technology

Evaluating Timoshenko Method for Analyzing CLT under Out-of-Plane Loading

M. D. Tanvir Rahman et al.

BUILDINGS (2020)

添加到收藏夹

Article Mechanics

A novel Top Surface Analysis method for Mode I interface characterisation using Digital Image Correlation

Johannes Reiner et al.

ENGINEERING FRACTURE MECHANICS (2017)

添加到收藏夹

Article Forestry

Quasi-brittle fracture and size effect of glued laminated timber beams

Lukas Blank et al.

EUROPEAN JOURNAL OF WOOD AND WOOD PRODUCTS (2017)

添加到收藏夹

Article Mathematics, Applied

Three-dimensional constitutive modelling of arbitrarily orientated timber based on continuum damage mechanics

M. Gharib et al.

FINITE ELEMENTS IN ANALYSIS AND DESIGN (2017)

添加到收藏夹

Review Green & Sustainable Science & Technology

The wood from the trees: The use of timber in construction

Michael H. Ramage et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)

添加到收藏夹

Article Mechanics

Multi-scale modelling of rolling shear failure in cross-laminated timber structures by homogenisation and cohesive zone models

E. I. Saavedra Flores et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2016)

添加到收藏夹

Article Forestry

Mixed-mode fracture toughness of bond lines of PRF and PUR adhesives in European beech wood

Samuel Ammann et al.

HOLZFORSCHUNG (2015)

添加到收藏夹

Article Mechanics

Analysis of the fracture behavior of Radiata Pine timber and Laminated Veneer Lumber

Bettina Franke et al.

ENGINEERING FRACTURE MECHANICS (2014)

添加到收藏夹

Article Construction & Building Technology

Experimental results of fracture energy and fracture toughness of Radiata Pine laminated veneer lumber (LVL) in mode I (opening)

Manoochehr Ardalany et al.

MATERIALS AND STRUCTURES (2012)

添加到收藏夹

Article Mechanics

Shear and crack tip deformation correction for the double cantilever beam and three-point end-notched flexure specimens for mode I and mode II fracture toughness measurement of wood

Hiroshi Yoshihara et al.

ENGINEERING FRACTURE MECHANICS (2009)

添加到收藏夹

Article Mechanics

Equivalent crack based mode II fracture characterization of wood

MFSF de Moura et al.

ENGINEERING FRACTURE MECHANICS (2006)

添加到收藏夹

Article Engineering, Geological

Shear fracture (Mode II) of brittle rock

QH Rao et al.

INTERNATIONAL JOURNAL OF ROCK MECHANICS AND MINING SCIENCES (2003)

添加到收藏夹

Article Materials Science, Composites

Numerical simulation of mixed-mode progressive delamination in composite materials

PP Camanho et al.

JOURNAL OF COMPOSITE MATERIALS (2003)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.