☆ 4.8 Article

Additive manufacturing of yttrium-stabilized tetragonal zirconia: Progressive wall collapse, martensitic transformation, and energy dissipation in micro-honeycombs

ADDITIVE MANUFACTURING (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Ceramics

High strength and microwave-absorbing polymer-derived SiCN honeycomb ceramic prepared by 3D printing

Zhenxue Pan et al.

Summary: The study successfully fabricated SiCN honeycomb ceramic with excellent mechanical and microwave-absorbing properties by optimizing the ratio of multifunctional acrylates. At low temperatures, the free carbon nanodiamonds formed through the copolymerization of acrylate and polysilazane give SiCN honeycomb ceramic an extremely high microwave absorption rate.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Materials Science, Ceramics

Role of grain constraint on the martensitic transformation in ceria-doped zirconia

Edward L. Pang et al.

Summary: By conducting a comparative study on sintered pellets and powders, this research investigates the reasons behind decreased transformation temperatures and incomplete transformation in zirconia materials. The study finds that transformation temperatures are depressed in pellets due to grain constraint, while incomplete transformation in powders is attributed to insufficient driving force.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Mechanical properties of 3D printed ceramic cellular materials with triply periodic minimal surface architectures

Minhao Shen et al.

Summary: This study implemented four types of triply periodic minimal surface (TPMS) via digital light processing technology to create cellular ceramics and experimentally investigated their mechanical properties. Results showed that compressive strength of TPMS structures increases with relative density, with s14 structure exhibiting the highest compressive strength among the tested structures. The porosity dependence of Young's modulus of sintered zirconia TPMS suggests a better prediction using the Pabst-Gregorova exponential relation compared to the classical Gibson-Ashby model.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Grain-size effect on cracking accumulation in yttria-doped zirconia ceramics during cyclic martensitic transformations

Isabel R. Crystal et al.

Summary: Bulk polycrystalline zirconia-based ceramics often crack during martensitic transformations due to transformation mismatch stresses. Smaller grain sizes require more cycles to disaggregate due to larger grain boundary area that must crack. The energy relieved through cracking decreases with increasing grain size, suggesting the need for alternate accommodation mechanisms at larger grain sizes to relieve transformation mismatch stresses.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Engineering, Mechanical

Mechanical properties and failure behaviour of architected alumina microlattices fabricated by stereolithography 3D printing

Xiu Yun Yap et al.

Summary: Alumina microlattices with different topologies were fabricated using stereolithography 3D printing method. The mechanical properties were highest in Simple Cubic lattices and deviated from Ashby's power law at higher relative densities due to joint deformation. Failure mechanisms were discussed using finite element simulation analysis, showing that the microlattices exhibited better specific modulus and strength than many engineering materials.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Architected cellular materials: A review on their mechanical properties towards fatigue-tolerant design and fabrication

M. Benedetti et al.

Summary: Metal additive manufacturing is now a mature technology that is being used to produce high-performance parts, including mission-critical components. The intentional design of porous metal structures, such as cellular or lattice structures, offers advantages in terms of specific mechanical or performance characteristics. While concerns over structural integrity remain, improvements in the manufacturing processes are leading to better fatigue properties for additively manufactured cellular structures.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2021)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication of ZrO2 and ATZ materials via UV-LCM-DLP additive manufacturing technology

Mario Borlaf et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Phase field modeling of crack propagation in shape memory ceramics Application to zirconia

Ehsan Moshkelgosha et al.

COMPUTATIONAL MATERIALS SCIENCE (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of the Layer Height and Exposure Energy on the Lateral Resolution of Zirconia Parts Printed by Lithography-Based Additive Manufacturing

Laura Conti et al.

MATERIALS (2020)

添加到收藏夹

Article Materials Science, Ceramics

3D printing of zirconia via digital light processing: optimization of slurry and debinding process

Jinxing Sun et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical properties of zirconia octet truss structures fabricated by DLP 3D printing

Weiming Zhao et al.

MATERIALS RESEARCH EXPRESS (2020)

添加到收藏夹

Article Physics, Applied

Effects of mechanical constraint on thermally induced reverse martensitic transformation in granular shape memory ceramic packings

Hunter A. Rauch et al.

JOURNAL OF APPLIED PHYSICS (2020)

添加到收藏夹

Article Dentistry, Oral Surgery & Medicine

Effect of the volume fraction of zirconia suspensions on the microstructure and physical properties of products produced by additive manufacturing

Kyoung-Jun Jong et al.

DENTAL MATERIALS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

In situ investigation of stress-induced martensitic transformation in granular shape memory ceramic packings

Hunter A. Rauch et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Ceramics

Development of UV-curable ZrO2 slurries for additive manufacturing (LCM-DLP) technology

Mario Borlaf et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Additive Manufacturing of ceramic components by Digital Light Processing: A comparison between the bottom-up and the top-down approaches

Oscar Santoliquido et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Stereolithographic 3D Printing-Based Hierarchically Cellular Lattices for High-Performance Quasi-Solid Supercapacitor

Jianzhe Xue et al.

NANO-MICRO LETTERS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Thermal conductivity of architected cellular metamaterials

A. Mirabolghasemi et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Robust Cellular Shape-Memory Ceramics via Gradient-Controlled Freeze Casting

Xiaomei Zeng et al.

ADVANCED ENGINEERING MATERIALS (2019)

添加到收藏夹

Article Materials Science, Ceramics

Effect of surface treatment on the dispersion of nano zirconia particles in non-aqueous suspensions for stereolithography

Jinxing Sun et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Physics, Applied

Stress-induced phase transformation in shape memory ceramic nanoparticles

V. S. Raut et al.

JOURNAL OF APPLIED PHYSICS (2019)

添加到收藏夹

Article Chemistry, Physical

Three-dimensional printing of piezoelectric materials with designed anisotropy and directional response

Huachen Cui et al.

NATURE MATERIALS (2019)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication of complex-shaped zirconia ceramic parts via a DLP-stereolithography-based 3D printing method

Rongxuan He et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Chemistry, Physical

Rheological and Curing Behavior of Acrylate-Based Suspensions for the DLP 3D Printing of Complex Zirconia Parts

Dmitrii A. Komissarenko et al.

MATERIALS (2018)

添加到收藏夹

Article Engineering, Mechanical

A Survey of Modeling of Lattice Structures Fabricated by Additive Manufacturing

Guoying Dong et al.

JOURNAL OF MECHANICAL DESIGN (2017)

添加到收藏夹

Article Materials Science, Ceramics

Fractography of zirconia-specimens made using additive manufacturing (LCM) technology

Walter Harrer et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

添加到收藏夹

Article Engineering, Biomedical

3D-printing zirconia implants; a dream or a reality? An in-vitro study evaluating the dimensional accuracy, surface topography and mechanical properties of printed zirconia implant and discs

Reham B. Osman et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical properties of 3D printed polymeric cellular materials with triply periodic minimal surface architectures

Diab W. Abueidda et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Materials Science, Ceramics

3D gel-printing of zirconia ceramic parts

Huiping Shao et al.

CERAMICS INTERNATIONAL (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Granular shape memory ceramic packings

Hang Z. Yu et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Ceramics

Additive manufacturing and mechanical characterization of high density fully stabilized zirconia

Amir Ghazanfari et al.

CERAMICS INTERNATIONAL (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Superelasticity in micro-scale shape memory ceramic particles

Zehui Du et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Review Materials Science, Multidisciplinary

Ceramic Stereolithography: Additive Manufacturing for Ceramics by Photopolymerization

John W. Halloran

ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 46 (2016)

添加到收藏夹

Review Materials Science, Multidisciplinary

Architected Cellular Materials

Tobias A. Schaedler et al.

ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 46 (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Lightweight Metal Cellular Structures Fabricated via 3D Printing of Sand Cast Molds

Dean Snelling et al.

ADVANCED ENGINEERING MATERIALS (2015)

添加到收藏夹

Article Engineering, Civil

Analysis and optimisation of parameters influencing the out-of-plane energy absorption of an aluminium honeycomb

Suchao Xie et al.

THIN-WALLED STRUCTURES (2015)

添加到收藏夹

Article Chemistry, Multidisciplinary

3D-Printing of Lightweight Cellular Composites

Brett G. Compton et al.

ADVANCED MATERIALS (2014)

添加到收藏夹

Article Multidisciplinary Sciences

High-strength cellular ceramic composites with 3D microarchitecture

Jens Bauer et al.

PROCEEDINGS OF THE NATIONAL ACADEMY OF SCIENCES OF THE UNITED STATES OF AMERICA (2014)

添加到收藏夹

Article Physics, Applied

Grain boundary and triple junction constraints during martensitic transformation in shape memory alloys

Stian M. Ueland et al.

JOURNAL OF APPLIED PHYSICS (2013)

添加到收藏夹

Article Multidisciplinary Sciences

Shape Memory and Superelastic Ceramics at Small Scales

Alan Lai et al.

SCIENCE (2013)

添加到收藏夹

Review Multidisciplinary Sciences

Micro-architectured materials: past, present and future

N. A. Fleck et al.

PROCEEDINGS OF THE ROYAL SOCIETY A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES (2010)

添加到收藏夹

Article Dentistry, Oral Surgery & Medicine

Direct Inkjet Printing of dental Prostheses Made of Zirconia

J. Ebert et al.

JOURNAL OF DENTAL RESEARCH (2009)

添加到收藏夹

Article Materials Science, Ceramics

The Tetragonal-Monoclinic Transformation in Zirconia: Lessons Learned and Future Trends

Jerome Chevalier et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2009)

添加到收藏夹

Article Materials Science, Ceramics

Ceramics for medical applications: A picture for the next 20 years

J. Chevalier et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2009)

添加到收藏夹

Article Chemistry, Physical

Calculation of interparticle spacing in colloidal systems

T Hao et al.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2006)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of rubber encapsulation on the comparative mechanical behaviour of ceramic honeycomb and foam

V Jain et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.