☆ 4.7 Article

High-strength vacuum diffusion bonding of Cu-plated, sandblasted W and CuCrZr alloy

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

Tensile strength improvement of martensitic ODS steels with Zr and Hf additions

Xiaosheng Zhou et al.

Summary: This study evaluated the effectiveness of Zr and Hf additions on oxide particle refinement and tensile strength improvement in transformable ODS steels. It was found that the tempered 9Cr-Hf steel exhibited superior tensile strength, while the tempered 9Cr-Zr steel showed a good combination of tensile strength and ductility. The study suggests that Zr and Hf can be considered as potential microalloying elements for producing ODS steels with favorable mechanical performance.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Supermodulus effect by grain-boundary wetting in nanostructured multilayers

Jing Wang et al.

Summary: The study systematically investigated the effect of thermal treatments on mechanical properties in Ni/Mo multilayers. A supermodulus effect and large tensile stress development were observed in the annealed multilayers, along with the evolution of grain-boundary wetting. The results highlight the crucial role of interfacial structures in governing the elastic behavior of metallic multilayers.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Direct alloying of immiscible molybdenum-silver system and its thermodynamic mechanism

Jinlong Du et al.

Summary: A direct alloying method was developed to achieve direct alloying between Mo and Ag in an immiscible system, constructing a successful Mo-Ag metallurgical bonding interface. Mechanical tests and a thermodynamic model confirmed the feasibility and mechanism of direct alloying, overcoming the positive formation heat in Mo-Ag systems.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Low-temperature densification and microstructure of W-Cu composites with Sn additives

Yuan Li et al.

Summary: High-strength dense and homogeneous W-Cu composites were successfully prepared using Cu-coated W powders and hot pressure sintering with Sn as activated additives. The addition of 2 wt.% Sn significantly promoted densification, increased Vickers hardness to 263.5 HV, and strengthened interface bonding of sintered composites.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of diffusion bonded joints of high-entropy alloy Al5(HfNbTiZr)95 and TC4 titanium alloy

Yu Peng et al.

Summary: TC4 (Ti-6Al-4V) titanium alloy and Al-5(HfNbTiZr) 95 refractory high-entropy alloy were successfully diffusion bonded at a temperature range of 800-1000 degrees C for 60 min under 5 MPa. The microstructure and mechanical properties of the diffusion bonded joints were investigated, revealing a parabolic growth of reaction zones and an increase in shear strength with bonding temperature. A maximum shear strength of 770.06 MPa was achieved at a bonding temperature of 950 degrees C for 60 min under 5 MPa.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-strength diffusion bonding of oxide-dispersion-strengthened tungsten and CuCrZr alloy through surface nano-activation and Cu plating

Yuanyuan Chen et al.

Summary: A three-step bonding process involving surface nano-activation, copper plating followed by annealing, and diffusion bonding was used to bond ODS-W and a CuCrZr alloy. The morphological and structural evolutions were thoroughly studied, resulting in well-cohesive ODS-W/Cu and ODS-W/Y2O3/Cu interfaces with high shear strengths and effective bonded area ratios. This developed bonding process provides effective support for future plasma-facing components in nuclear fusion reactor applications.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interface diffusion and mechanical properties of ODS-W/Cu prepared by spark plasma sintering

Dong-Guang Liu et al.

Summary: In this study, ODS-W and copper powders were successfully combined by spark plasma sintering in the absence of an intermediate layer. The diffusion distance of Cu and W increased with bonding temperature, with the joint at 980°C showing the best performance. At this temperature, no microcracks or pores were formed, and the tensile strength and hardness were significantly improved.

VACUUM (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Controlled synthesis of high-quality W-Y2O3 composite powder precursor by ascertaining the synthesis mechanism behind the wet chemical method

Zhi Dong et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Nuclear Science & Technology

Joining of oxygen-free high-conductivity Cu to CuCrZr by direct diffusion bonding without using an interlayer at Low temperature

Can Zhao et al.

FUSION ENGINEERING AND DESIGN (2020)

添加到收藏夹

Article Nuclear Science & Technology

Influence of helium ion irradiation damage behavior after laser thermal shock of W-2%vol Y2O3 composites

Gang Yao et al.

PROGRESS IN NUCLEAR ENERGY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

The simultaneous improvements of strength and ductility in W-Y2O3 alloy obtained via an alkaline hydrothermal method and subsequent low temperature sintering

Zhi Dong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nuclear Science & Technology

High-temperature mechanical behaviors of diffusion-welded Alloy 617

Injin Sah et al.

NUCLEAR ENGINEERING AND DESIGN (2020)

添加到收藏夹

Article Engineering, Chemical

Sandblasting parameter variation effect on galvanized steel surface chemical composition, roughness and free energy

A. Bechikh et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2020)

添加到收藏夹

Article Materials Science, Biomaterials

Empirical and theoretical insights into the structural effects of selenite doping in hydroxyapatite and the ensuing inhibition of osteoclasts

Victoria M. Wu et al.

MATERIALS SCIENCE AND ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2020)

添加到收藏夹

Article Chemistry, Physical

Thermodynamic mechanism for direct alloying of immiscible tungsten and copper at a critical temperature range

Jie Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution and interface structure of Al-40 wt% Si composites produced by high-energy ball milling

Yuanyuan Chen et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Vacuum diffusion bonding W to W-Cu composite: Interfacial microstructure and mechanical properties

Haixiang Yan et al.

VACUUM (2019)

添加到收藏夹

Article Engineering, Manufacturing

Evaluation of the bonded ratio of TC4 diffusion bonded joints based on ultrasonic C-scan

J. T. Xiong et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Preparation of a nanoporous active tungsten foil by two-step anodizing and deoxidized annealing for hydrogen evolution reaction

Jie Zhang et al.

NANOTECHNOLOGY (2019)

添加到收藏夹

Article Engineering, Chemical

Improvement of aluminum lithium alloy adhesion performance based on sandblasting techniques

Jian Li et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2018)

添加到收藏夹

Article Engineering, Industrial

Microstructural and mechanical characterizations of W/CuCrZr and W/steel joints brazed with Cu-22TiH2 filler

Liangxing Peng et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

添加到收藏夹

Article Instruments & Instrumentation

Repair behavior of He+-irradiated W-Y2O3 composites after different temperature-isochronal annealing experiments

Gang Yao et al.

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Direct diffusion bonding of immiscible tungsten and copper at temperature close to Copper's melting point

Jie Zhang et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Article Nuclear Science & Technology

Investigation of tungsten/steel diffusion bonding with Ni-Fe cladding on tungsten substrate

Qingshan Cai et al.

FUSION ENGINEERING AND DESIGN (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Comprehensive enhancement of the mechanical and thermo-mechanical properties of W/Cu joints via femtosecond laser fabricated micro/nano interface structures

Dafa Jiang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Physics, Fluids & Plasmas

Baseline high heat flux and plasma facing materials for fusion

Y. Ueda et al.

NUCLEAR FUSION (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Femtosecond laser fabricated micro/nano interface structures toward enhanced bonding strength and heat transfer capability of W/Cu joining

Dafa Jiang et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Nuclear Science & Technology

Investigation of tungsten/steel brazing using Ta and Cu interlayer

Wensheng Liu et al.

FUSION ENGINEERING AND DESIGN (2016)

添加到收藏夹

Article Engineering, Chemical

Effect of grit-blasting air pressure on adhesion strength of resin to titanium

Aftab Ahmed Khan et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2016)

添加到收藏夹

Article Engineering, Chemical

The effect of sandblasting on surface properties for adhesion

Anna Rudawska et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2016)

添加到收藏夹

Article Engineering, Chemical

Effects of sandblasting distance and angles on resin cement bonding to zirconia and titanium

Beatrice Jane Ho et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Process optimization for diffusion bonding of tungsten with EUROFER97 using a vanadium interlayer

Widodo Widjaja Basuki et al.

JOURNAL OF NUCLEAR MATERIALS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of W/Cu vacuum diffusion bonding joints using amorphous Fe-W alloy as interlayer

Song Wang et al.

VACUUM (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Bonding Interface of W-CuCrZr Explosively Welded Composite Plates for Plasma Facing Components

Congxiao Sun et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Thermomechanical analysis of diffusion-bonded tungsten/EUROFER97 with a vanadium interlayer

Widodo Widjaja Basuki et al.

JOURNAL OF NUCLEAR MATERIALS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Diffusion bonding between W and EUROFER97 using V interlayer

Widodo Widjaja Basuki et al.

JOURNAL OF NUCLEAR MATERIALS (2012)

添加到收藏夹

Article Chemistry, Physical

Effects of surface roughness and energy on ice adhesion strength

M. Zou et al.

APPLIED SURFACE SCIENCE (2011)

添加到收藏夹

Article Nuclear Science & Technology

High heat load properties of actively cooled W/CuCrZr mock-ups by diffusion bonding with Ni or Ti interlayer

Jun Li et al.

FUSION ENGINEERING AND DESIGN (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation on the diffusion bonding of tungsten and EUROFER97

Widodo Widjaja Basuki et al.

JOURNAL OF NUCLEAR MATERIALS (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical properties of HIP bonded W and Cu-alloys joint for plasma facing components

S Saito et al.

JOURNAL OF NUCLEAR MATERIALS (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.