相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。The influence of temperature on the elastic properties of body-centered cubic reduced activation steels
Xiaojie Li et al.
MATERIALS & DESIGN (2021)
Effect of test temperature on flow behavior and strain hardening of magnesium under high strain rate deformation conditions
Bidyapati Mishra et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Effects of annealing on the structure and mechanical properties of FeCoCrNi high-entropy alloy fabricated via selective laser melting
Danyang Lin et al.
ADDITIVE MANUFACTURING (2020)
Solute-dislocation interactions and creep-enhanced Cu precipitation in a novel ferritic-martensitic steel
Bo Xiao et al.
ACTA MATERIALIA (2020)
Microstructures, tensile properties and serrated flow of AlxCrMnFeCoNi high entropy alloys
Jun Xu et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)
Laser additive manufacturing of Mg-based composite with improved degradation behaviour
Youwen Yang et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2020)
Effect of cyclic rapid thermal loadings on the microstructural evolution of a CrMnFeCoNi high-entropy alloy manufactured by selective laser melting
H. Wang et al.
ACTA MATERIALIA (2020)
High temperature deformation behavior of dual-phase Al0.6CoCrFeNi high-entropy alloys
Tangqing Cao et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
On the strain rate sensitivity of size-dependent plasticity in BCC iron at elevated temperatures: Discrete dislocation dynamics investigation
Pascale El Ters et al.
MECHANICS OF MATERIALS (2020)
A Si-containing FeCoCrNi high-entropy alloy with high strength and ductility synthesized in situ via selective laser melting
Danyang Lin et al.
ADDITIVE MANUFACTURING (2020)
Structure and mechanical properties of a FeCoCrNi high-entropy alloy fabricated via selective laser melting
Danyang Lin et al.
INTERMETALLICS (2020)
A strong, ductile, high-entropy FeCoCrNi alloy with fine grains fabricated via additive manufacturing and a single cold deformation and annealing cycle
Danyang Lin et al.
ADDITIVE MANUFACTURING (2020)
PNADIS: An automated Peierls-Nabarro analyzer for dislocation core structure and slip resistance
S. H. Zhang et al.
COMPUTER PHYSICS COMMUNICATIONS (2019)
Elemental segregation in an AlCoCrFeNi high-entropy alloy - A comparison between selective laser melting and induction melting
Dennis Karlsson et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Strain dependent constitutive model and microstructure evolution of a novel 9Cr martensitic steel during high-temperature deformation
Bo Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
A novel face-centered-cubic high-entropy alloy strengthened by nanoscale precipitates
Gang Qin et al.
SCRIPTA MATERIALIA (2019)
Probing deformation mechanisms of a FeCoCrNi high-entropy alloy at 293 and 77 K using in situ neutron diffraction (vol 154C, pg 79, 2018)
Yiqiang Wang et al.
ACTA MATERIALIA (2019)
Laser additive manufacturing of FeCrCoMnNi high-entropy alloy: Effect of heat treatment on microstructure, residual stress and mechanical property
Zhaopeng Tong et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Investigation of ductile damage during surface mechanical attrition treatment for TWIP steels using a dislocation density based viscoplasticity and damage models
Zhenglin Chen et al.
MECHANICS OF MATERIALS (2019)
Additively manufactured CoCrFeNiMn high-entropy alloy via pre-alloyed powder
Pan Wang et al.
MATERIALS & DESIGN (2019)
Probing deformation mechanisms of a FeCoCrNi high-entropy alloy at 293 and 77 K using in situ neutron diffraction
Yiqiang Wang et al.
ACTA MATERIALIA (2018)
Composition design of high entropy alloys using the valence electron concentration to balance strength and ductility
Ruirun Chen et al.
ACTA MATERIALIA (2018)
A review on fundamental of high entropy alloys with promising high-temperature properties
Jian Chen et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Selective laser melting of an equiatomic CoCrFeMnNi high-entropy alloy: Processability, non-equilibrium microstructure and mechanical property
Ruidi Li et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Temperature dependent deformation mechanisms of Al0.3CoCrFeNi high-entropy alloy, starting from serrated flow behavior
Yu Zhang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Dislocation network in additive manufactured steel breaks strength-ductility trade-off
Leifeng Liu et al.
MATERIALS TODAY (2018)
Deformation of CoCrFeNi high entropy alloy at large strain
Bing Wang et al.
SCRIPTA MATERIALIA (2018)
Hierarchical microstructure and strengthening mechanisms of a CoCrFeNiMn high entropy alloy additively manufactured by selective laser melting
Z. G. Zhu et al.
SCRIPTA MATERIALIA (2018)
Microstructure and properties of laser re-melting FeCoCrNiAl0.5Six. high-entropy alloy coatings
Bingqian Jin et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Mechanical and corrosion properties of AlCoCrFeNi high-entropy alloy fabricated with selective electron beam melting
Kosuke Kuwabara et al.
ADDITIVE MANUFACTURING (2018)
Tensile mechanical properties, constitutive equations, and fracture mechanisms of a novel 9% chromium tempered martensitic steel at elevated temperatures
Bo Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Basic modelling of creep rupture in austenitic stainless steels
Junjing He et al.
THEORETICAL AND APPLIED FRACTURE MECHANICS (2017)
A precipitation-hardened high-entropy alloy with outstanding tensile properties
J. Y. He et al.
ACTA MATERIALIA (2016)
Thermo-physical simulation of the compression testing for constitutive modeling of GH4169 superalloy during linear friction welding
Xiawei Yang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2016)
Hot deformation behavior of extruded Mg-Zn-Y-Zr alloy
Xiangsheng Xia et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
The use of high-entropy alloys in additive manufacturing
Yevgeni Brif et al.
SCRIPTA MATERIALIA (2015)
Microstructural evolution and constitutive relationship of Al-Zn-Mg alloy containing small amount of Sc and Zr during hot deformation based on Arrhenius-type and artificial neural network models
Bo Li et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes
JW Yeh et al.
ADVANCED ENGINEERING MATERIALS (2004)
Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues
LP Kubin et al.
SCRIPTA MATERIALIA (2003)
分享论文
