相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Non-destructive detection of machining-induced white layers through grain size and crystallographic texture-sensitive methods
M. Brown et al.
MATERIALS & DESIGN (2021)
Plastic Strain Threshold Determination for White Layer Formation in Hard Turning of AISI 52100 Steel Using Micro-Grid Technique and Finite Element Simulations
Guang-Chao Nie et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2020)
Tool wear induced modifications of plastic flow and deformed material depth in new generated surfaces during turning Ti-6Al-4V
Xiaoliang Liang et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Grain refinement mechanism under high strain-rate deformation in machined surface during high speed machining Ti6Al4V
Xiang Xu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Quantitative characterization of machining-induced white layers in Ti-6Al-4V
M. Brown et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Investigating effects of milling conditions on cutting temperatures through analytical and experimental methods
Umut Karaguzel et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Destructive and non-destructive testing methods for characterization and detection of machining-induced white layer: A review paper
M. Brown et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2018)
FEM-simulation of machining induced surface plastic deformation and microstructural texture evolution of Ti-6A1-4V alloy
Anhai Li et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)
Effect of microstructure and cutting speed on machining behavior of Ti6Al4V alloy
Sagar V. Telrandhe et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2017)
The Influence of Cutting Heat on the Surface Integrity during Machining of Titanium Alloy Ti6Al4V
Sandip Patil et al.
44TH NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE, NAMRC 44 (2016)
Formation mechanisms of white layers induced by hard turning of AISI 52100 steel
S. B. Hosseini et al.
ACTA MATERIALIA (2015)
The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718™
A. R. C. Sharman et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Continuous dynamic recrystallization during severe plastic deformation
Mattia Bacca et al.
MECHANICS OF MATERIALS (2015)
Influence of the cutting edge radius on surface integrity in hard turning of roller bearing inner rings
B. Denkena et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2015)
Sub-Millimeter Measurement of Finite Strains at Cutting Tool Tip Vicinity
T. Pottier et al.
EXPERIMENTAL MECHANICS (2014)
Influence of Surface Anomalies Following Hole Making Operations on the Fatigue Performance for a Nickel-Based Superalloy
C. Herbert et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2014)
Evaluating the subsurface microstructure of machined Ti-6Al-4V
Kyle D. Edkins et al.
2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) (2014)
Analysis of the white layers formed during machining of hardened AISI 52100 steel under dry and cryogenic cooling conditions
Domenico Umbrello
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Quantitative Strain Analysis of the Large Deformation at the Scale of Microstructure: Comparison between Digital Image Correlation and Microgrid Techniques
H. Ghadbeigi et al.
EXPERIMENTAL MECHANICS (2012)
The variation of strain rate sensitivity exponent and strain hardening exponent in isothermal compression of Ti-6Al-4V alloy
Jiao Luo et al.
MATERIALS & DESIGN (2010)
The basic relationships between residual stress, white layer, and fatigue life of hard turned and ground surfaces in rolling contact]
Y. B. Guo et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2010)
A finite element modeling approach to predicting white layer formation in nickel superalloys
S. Ranganath et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2009)
Determination of micro-scale plastic strain caused by orthogonal cutting
H. Ghadbelgi et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Metallographic analysis of the deformation microstructure of copper subjected to orthogonal cutting
M Elmadagli et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
On thermoplastic shear instability in the machining of a titanium alloy (Ti-6Al-4V)
R Komanduri et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2002)
Overview -: Residual stress part 1 -: Measurement techniques
PJ Withers et al.
MATERIALS SCIENCE AND TECHNOLOGY (2001)