☆ 4.7 Article

Numerical study on premixed hydrogen/air combustion characteristics and heat transfer enhancement of micro-combustor embedded with pin fins

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

A numerical study on non-premixed H2/air flame stability in a micro-combustor with a slotted bluff-body

Linhong Li et al.

Summary: Researchers developed a planar micro-combustor with a slotted bluff-body for non-premixed H-2/air combustion and found that a medium blockage ratio of the bluff-body can provide a trade-off between positive and negative impacts on flame blow-off, leading to the largest blow-off limit.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Effects of micro-combustor geometry and size on the heat transfer and combustion characteristics of premixed hydrogen/air flames

Alireza Rahbari et al.

Summary: The major challenge in the development of micro-combustors is flame instabilities, which lead to non-uniform wall temperature distribution and lower combustion efficiency. This research investigates the combustion characteristics and geometrical configurations on flame stability and combustion efficiency, with a detailed chemical reaction mechanism developed and parametric study conducted. Increasing thermal conductivity coefficient, equivalence ratio, and using a micro-combustor with bluff body are identified as effective ways to improve combustion performance.

ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Non-premixed combustion characteristics and thermal performance of a catalytic combustor for micro-thermophotovoltaic systems

Linhong Li et al.

Summary: The study verified that a symmetrical configuration of micro-combustor can improve combustion efficiency and radiation efficiency, allowing it to operate at higher average velocities. Furthermore, as the average velocity increases, combustion efficiency decreases monotonically while radiation efficiency and radiant energy output increase first and then decrease.

ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical investigation on a multi-channel micro combustor fueled with hydrogen for a micro-thermophotovoltaic system

Ziqiang He et al.

Summary: This study compared the heat transfer performance and energy output of different channel shapes MCMC and CMC in the MTPV system, finding that the MCMC with diamond channels had a higher outer wall temperature at a certain flow rate. Additionally, the double-layer MCMC with counterflow structure achieved the highest total energy conversion efficiency under specific conditions.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Thermal performance improvement of premixed hydrogen/air fueled cylindrical micro-combustor using a preheater-conductor plate

Shiguang Wu et al.

Summary: A novel preheater-conductor plate was designed to be inserted into a cylindrical micro-combustor to improve the outer wall temperature and the exergy efficiency. The study investigated the impact of different factors on the thermal performance of the micro-combustor, finding that the proposed preheater-conductor plate significantly improved the system's performance.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Review Thermodynamics

Process in micro-combustion and energy conversion of micro power system: A review

E. Jiaqiang et al.

Summary: This article reviews the research on micro power equipment focusing on flame optimization and energy conversion efficiency. Different influencing parameters in various systems, such as combustion efficiency and conversion efficiency, are analyzed, emphasizing the significance of energy conversion efficiency in micro power equipment.

ENERGY CONVERSION AND MANAGEMENT (2021)

添加到收藏夹

Review Energy & Fuels

Recent progress in flame stabilization technologies for combustion-based micro energy and power systems

Jianlong Wan et al.

Summary: This article discusses the development and classification of flame stabilization technologies in micro-combustors, including single flame stabilization technologies, combined flame stabilization technologies, and other technologies. Progress made in the past decade is summarized, along with a discussion on the underlying mechanisms of these flame anchoring strategies.

FUEL (2021)

添加到收藏夹

Article Thermodynamics

Convective heat transfer of nano-encapsulated phase change material suspension in a divergent minichannel heatsink

C. J. Ho et al.

Summary: The phase change heat transfer of NEPCM particles can significantly enhance heat transfer efficiency at low Reynolds numbers and low heating powers, but its advantage over pure water diminishes at large Reynolds numbers.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

添加到收藏夹

Article Chemistry, Physical

Enhance the energy and exergy performance of hydrogen combustion by improving the micro-combustor outlet in thermofluidic systems

Salar Mohseni et al.

Summary: This study focuses on improving the exit part of conventional micro-combustors to increase heat transfer efficiency and decrease exhaust gas temperature. By enhancing exhaust gas velocity and increasing heat transfer surface area, the new micro-combustors show reduced exhaust gas temperature and increased wall temperature uniformity. Furthermore, micro combustors with porous media demonstrate the best energy and exergy performance.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical study on the influence of controllable flow ratio on combustion characteristics of a controllable central slotted bluff body and cavity combined micro combustor

Fulei Xu et al.

Summary: The CC micro combustor with a controllable flow rate of 0.4 exhibits the highest combustion efficiency and better combustion stability under high inlet volume flow rates in micro combustion systems.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

A novel Swiss-roll micro-combustor with double combustion chambers: A numerical investigation on effect of solid material on premixed CH4/air flame blow-off limit

Lun Ma et al.

Summary: A novel Swiss-roll micro-combustor with double combustion chambers is proposed to improve flame stability and extend blow-off limits. Different solid materials (SiC, stainless steel, and copper) have a significant impact on flame stability and blow-off limits in micro-combustors. Good heat recirculation and low heat loss rates play a crucial role in influencing blow-off limits in micro-combustors.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Heat transfer enhancement and exergy efficiency improvement of a micro combustor with internal spiral fins for thermophotovoltaic systems

Ziqiang He et al.

Summary: By introducing internal spiral fins, the novel micro combustor can effectively improve the energy efficiency and output of micro thermophotovoltaic system, although with increased pressure loss. Experiment results demonstrate that the micro combustor with 8 spiral fins achieves the highest efficiency and energy output at different inlet velocities.

APPLIED THERMAL ENGINEERING (2021)

添加到收藏夹

Article Thermodynamics

Numerical investigations on hydrogen-fueled micro-cylindrical combustors with cavity for micro-thermophotovoltaic applications

Wei Zuo et al.

Summary: The study found that the micro-cylindrical combustor with cavity has better thermal performance compared to the one without cavity. By analyzing the effects of cavity length and depth, the optimal cavity size was determined, and it was concluded that the combustor with cavity has better potential for applications in micro-TPV systems.

ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Heat recirculation and heat losses in porous micro-combustors: Effects of wall and porous media properties and combustor dimensions

Jun Li et al.

Summary: The study aims to analyze heat fluxes in porous micro-combustors and discuss the effects of wall thermal conductivity and porous media properties on flame temperature. Results show that smaller porous micro-combustors have a higher proportion of heat recirculation relative to heat losses, and flame temperature is inversely related to the ratio of total heat losses to total heat recirculation.

ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

Effect analysis on energy conversion enhancement and NOx emission reduction of ammonia/hydrogen fuelled wavy micro-combustor for micro-thermophotovoltaic application

Lei Han et al.

Summary: The study found that the wavy combustors have higher average temperatures and improved temperature uniformity compared to conventional smooth combustors. The flame stability of hydrogen/ammonia blended combustion is better in the wavy combustors. NOx emission reduction can be achieved by increasing the nitrogen fuel mass ratio. This research demonstrates the effective design of a micro-combustor with enhanced thermal performance and reduced NOx emissions.

FUEL (2021)

添加到收藏夹

Article Chemistry, Applied

Energy conversion efficiency improvement studies on unconventional premixed micro-combustors partially inserted with porous medium

Siliang Ni et al.

Summary: This study investigates the thermal performance and radiation efficiency of micro-combustors with curved surfaces through experiments and numerical simulations. Results show that double-channel combustors have higher efficiency and porous medium improves temperature uniformity. The T-shaped combustor exhibits the best performance under certain conditions.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Thermodynamics

Effect analysis on performance enhancement of a hydrogen/air non-premixed micro combustor with sudden expansion and contraction structure

E. Jiaqiang et al.

Summary: The study focused on enhancing the non-premixed combustion performance of hydrogen/air in micro combustors, revealing the influence of combustor diameter and inlet velocity on stable combustion. An enhanced combustion method was proposed, showing that reducing hydrogen inlet velocity can significantly improve combustion stability.

ENERGY (2021)

添加到收藏夹

Article Chemistry, Applied

Role of hydrogen addition in propane/air flame characteristic and stability in a micro-planar combustor

Aikun Tang et al.

Summary: Experimental study on micro-scale combustion with a micro-planar quartz combustor shows that blending hydrogen significantly extends flame stability by overcoming flame instability and inhibiting flame type transition. The addition of hydrogen affects flame dynamics and helps maintain flame symmetry.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Chemistry, Physical

Thermal performance characteristics of a micro-combustor with swirl rib fueled with premixed hydrogen/air

Shiguang Wu et al.

Summary: A swirl rib was designed to improve the thermal efficiency of a micro-combustor in this study, with trapezoidal rib showing the best thermal performance. This research provides theoretical guidance for the optimal design of hydrogen-fueled micro-combustors.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical comparison of premixed H2/air combustion characteristic of three types of micro cavity-combustors with guide vanes, bluff body, guide vanes and bluff body respectively

Wei Gao et al.

Summary: The study compares the combustion characteristics of three types of micro cavity combustors with guide vanes, bluff body, and a combination of bluff body and guide vanes under different conditions. It is found that guide vanes greatly enhance combustion intensity and stability near the cavity, leading to increased combustion efficiency.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Influence of multi-structure optimization on the comprehensive performance of micro-cylindrical combustor inserting with spiral fin by using grey relational analysis and analysis of variance

Ting Zhao et al.

Summary: This study proposes a novel micro combustor with spiral fin to improve the energy output of thermophotovoltaic systems. By using grey relational grade and analysis of variance, the research identifies the key structure factors influencing the thermal and energy performance of the micro combustor and determines the optimal combination for enhanced efficiency.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical investigation of a novel micro combustor with a central and bilateral slotted blunt body

Ziqiang He et al.

Summary: The newly designed MCSB, with a central and bilateral slotted blunt body, shows significant improvement in combustion performance by effectively preventing flame tip opening and exhibiting higher combustion efficiency and blown-off limit. The blown-off limit of MCSB can reach up to 756 cm(3)/s at a flow rate ratio of 0.2 and a bluff body angle of 90 degrees, which is 61.5% higher than that of conventional combustors.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

Effect of dimethyl ether addition on flame stability of premixed methane/air in a micro-planar quartz combustor

Jianming Li et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2020)

添加到收藏夹

Article Thermodynamics

Experimental and numerical study on convective boiling in a staggered array of micro pin-fin microgap

Liang-Han Chien et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of channel length on propagation behaviors of non-premixed H2-air flames in Y-shaped micro combustors

Ying Xiang et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2020)

添加到收藏夹

Article Chemistry, Physical

Combustion characteristics and thermal enhancement of premixed hydrogen/air in micro combustor with pin fin arrays

Ziqiang He et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of rectangular rib on exergy efficiency of a hydrogen-fueled micro combustor

Qingqing Li et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2020)

添加到收藏夹

Article Thermodynamics

Forced convection heat transfer of Nano-Encapsulated Phase Change Material (NEPCM) suspension in a mini-channel heatsink

C. J. Ho et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

添加到收藏夹

Article Thermodynamics

Effects of heat transfer on flame stability limits in a planar micro-combustor partially filled with porous medium

Qingqing Li et al.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2019)

添加到收藏夹

Article Energy & Fuels

Comparison of combustion efficiency between micro combustors with single- and double-layered walls: A numerical study

Aiwu Fan et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2019)

添加到收藏夹

Article Chemistry, Physical

Numerical study on stability and influencing factors of heterogeneous reaction for hydrogen/oxygen mixture in planar catalytic micro combustor

Jianfeng Pan et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Thermodynamics

Experimental study of boiling heat transfer in a microchannel with nucleated-shape columnar micro-pin-fins

Wun-Rong Liao et al.

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2019)

添加到收藏夹

Article Chemistry, Physical

Investigation of combustion and emission performance of a micro combustor: Effects of bluff body insertion and oxygen enriched combustion conditions

Harun Yilmaz

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

The numerical study of the energy and exergy efficiencies of the micro-combustor by the internal micro-fin for thermophotovoltaic systems

Ebrahim Nadimi et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Chemistry, Physical

Response of heat release to equivalence ratio variations in high Karlovitz premixed H2/air flames at 20 atm

Xujiang Wang et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Chemistry, Physical

Numerical study on premixed hydrogen/air combustion characteristics in micro-combustor with slits on both sides of the bluff body

Yunfei Yan et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Thermodynamics

Experimental study on convective boiling flow and heat transfer in a microgap enhanced with a staggered arrangement of nucleated micro-pin-fins

Liang-Han Chien et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

添加到收藏夹

Article Thermodynamics

Effect of wall thermal conductivity on the stability of catalytic heat-recirculating micro-combustors

Junjie Chen et al.

APPLIED THERMAL ENGINEERING (2018)

添加到收藏夹

Article Thermodynamics

Numerical investigation of key parameters of the porous media combustion based Micro-Thermophotovoltaic system

Stephen Bani et al.

ENERGY (2018)

添加到收藏夹

Article Chemistry, Physical

Numerical investigation on combustion characteristics of methane/air in a micro-combustor with a regular triangular pyramid bluff body

Yunfei Yan et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2018)

添加到收藏夹

Article Energy & Fuels

Investigation of energy conversion and flame stability in a curved micro-combustor for thermo-photovoltaic (TPV) applications

Saad Akhtar et al.

APPLIED ENERGY (2017)

添加到收藏夹

Article Energy & Fuels

Numerical study on catalytic combustion and extinction characteristics of pre-mixed methane-air in micro flatbed channel under different parameters of operation and wall

Yunfei Yan et al.

FUEL (2016)

添加到收藏夹

Article Thermodynamics

Effect of thermal conductivity of solid wall on combustion efficiency of a micro-combustor with cavities

Jianlong Wan et al.

ENERGY CONVERSION AND MANAGEMENT (2015)

添加到收藏夹

Article Thermodynamics

Development of micro-thermophotovoltaic power generator with heat recuperation

W. M. Yang et al.

ENERGY CONVERSION AND MANAGEMENT (2014)

添加到收藏夹

Article Chemistry, Physical

A numerical investigation on combustion characteristics of H2/air mixture in a microcombustor with wall cavities

Jianlong Wan et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2014)

添加到收藏夹

Review Energy & Fuels

Development of micro power generators - A review

S. K. Chou et al.

APPLIED ENERGY (2011)

添加到收藏夹

Article Thermodynamics

Microthermophotovoltaic power generator with high power density

W. M. Yang et al.

APPLIED THERMAL ENGINEERING (2009)

添加到收藏夹

Article Engineering, Electrical & Electronic

Experimental and numerical study of the wall temperature of cylindrical micro combustors

J. Li et al.

JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2009)

添加到收藏夹

Review Chemistry, Physical

The development of a micropower (micro-thermophotovoltaic) device

Loy Chuan Chia et al.

JOURNAL OF POWER SOURCES (2007)

添加到收藏夹

Article Thermodynamics

Numerical modeling of non-adiabatic heat-recirculating combustors

C. H. Kuo et al.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2007)

添加到收藏夹

Article Physics, Applied

Study of catalytic combustion and its effect on microthermophotovoltaic power generators

WM Yang et al.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2005)

添加到收藏夹

Article Thermodynamics

A CFD study of propane/air microflame stability

DG Norton et al.

COMBUSTION AND FLAME (2004)

添加到收藏夹

Article Chemistry, Physical

An updated comprehensive kinetic model of hydrogen combustion

J Li et al.

INTERNATIONAL JOURNAL OF CHEMICAL KINETICS (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.