相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。The Effects of Feature Sizes in Selectively Laser Melted Ti-6Al-4V Parts on the Validity of Optimised Process Parameters
Chinmay Phutela et al.
MATERIALS (2020)
On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion
Fabrizia Caiazzo et al.
MATERIALS (2020)
On the size and orientation effect in additive manufactured Ti-6Al-4V
D. Barba et al.
MATERIALS & DESIGN (2020)
Mechanical properties of diamond lattice Ti-6Al-4V structures produced by laser powder bed fusion: On the effect of the load direction
Antonio Cutolo et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2020)
Processing parameters in laser powder bed fusion metal additive manufacturing
J. P. Oliveira et al.
MATERIALS & DESIGN (2020)
Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging
Ross Cunningham et al.
SCIENCE (2019)
Exploring the Correlation between Subsurface Residual Stresses and Manufacturing Parameters in Laser Powder Bed Fused Ti-6Al-4V
Tatiana Mishurova et al.
METALS (2019)
Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment
P. D. Nezhadfar et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
A new FE post-processor for probabilistic fatigue assessment in the presence of defects and its application to AM parts
S. Romano et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
An investigation into the effect of process parameters on melt pool geometry, cell spacing, and grain refinement during laser powder bed fusion
Ali Keshavarzkermani et al.
OPTICS AND LASER TECHNOLOGY (2019)
Heat and fluid flow in additive manufacturing - Part II: Powder bed fusion of stainless steel, and titanium, nickel and aluminum base alloys
T. Mukherjee et al.
COMPUTATIONAL MATERIALS SCIENCE (2018)
Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: A review
H. Shipley et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)
Scaling laws for the additive manufacturing
Alexander M. Rubenchik et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Additive manufacturing of fatigue resistant materials: Challenges and opportunities
Aref Yadollahi et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Fatigue Behavior and Modeling of Additively Manufactured Ti-6Al-4V Including Interlayer Time Interval Effects
Brian Torries et al.
JOM (2017)
Synchrotron-Based X-ray Microtomography Characterization of the Effect of Processing Variables on Porosity Formation in Laser Power-Bed Additive Manufacturing of Ti-6Al-4V
Ross Cunningham et al.
JOM (2017)
Progress Towards Metal Additive Manufacturing Standardization to Support Qualification and Certification
Mohsen Seifi et al.
JOM (2017)
On the limitations of Volumetric Energy Density as a design parameter for Selective Laser Melting
Umberto Scipioni Bertoli et al.
MATERIALS & DESIGN (2017)
Evaluating the Effect of Processing Parameters on Porosity in Electron Beam Melted Ti-6Al-4V via Synchrotron X-ray Microtomography
Ross Cunningham et al.
JOM (2016)
Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting
Galina Kasperovich et al.
MATERIALS & DESIGN (2016)
Tailoring surface quality through mass and momentum transfer modeling using a volume of fluid method in selective laser melting of TiC/AlSi10Mg powder
Donghua Dai et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)
Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg
Christian Weingarten et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel
Aref Yadollahi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Influence of defects on mechanical properties of Ti-6Al-4 V components produced by selective laser melting and electron beam melting
Haijun Gong et al.
MATERIALS & DESIGN (2015)
Spatial variation of melt pool geometry, peak temperature and solidification parameters during laser assisted additive manufacturing process
V. Manvatkar et al.
MATERIALS SCIENCE AND TECHNOLOGY (2015)
Density of additively-manufactured, 316L SS parts using laser powder-bed fusion at powers up to 400 W
Chandrika Kamath et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
Wayne E. King et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Parametric analysis of thermal behavior during selective laser melting additive manufacturing of aluminum alloy powder
Yali Li et al.
MATERIALS & DESIGN (2014)
Metal Fatigue Causing Cystoscope Rupture During Bladder Neck Incision
Alfonso Fernandez et al.
JSLS-JOURNAL OF THE SOCIETY OF LAPAROENDOSCOPIC SURGEONS (2011)
Consolidation phenomena in laser and powder-bed based layered manufacturing
J. -P. Kruth et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2007)
分享论文
