相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Effect of no-load rate on recast layer cutting by ultra fine wire-EDM
Ming Zhang et al.
CHINESE JOURNAL OF AERONAUTICS (2021)
Extreme wire electrical discharge machining based on semiconductor characteristics
Hongwei Pan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Experimental investigation into material removal mechanisms in High Speed Wire EDM (vol 111, pg 2163, 2020)
Kai Osswald et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Machining performance of Inconel 718 using graphene nanofluid in EDM
Kamlesh Paswan et al.
MATERIALS AND MANUFACTURING PROCESSES (2020)
Moving arc electrical discharge machining of polycrystalline diamond
Xiangzhi Wang et al.
MATERIALS AND MANUFACTURING PROCESSES (2020)
Erosion characteristics of electrical discharge machining using graphene powder in deionized water as dielectric
Xiangzhi Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Active gap capacitance electrical discharge machining of polycrystalline diamond
Xiangzhi Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
On processing of Inconel718 through multi-channel discharge ablation
Jiongbo Fu et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Energy distribution in cool electrode of electrical discharge machining based on wave-particle dualism
Qiu Mingbo et al.
MACHINING SCIENCE AND TECHNOLOGY (2019)
Effect of different dielectric fluids on material removal rate, surface roughness, kerf width and microhardness
Tina Chaudhary et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)
Machining of sub-cooled low carbon tool steel by wire-EDM
Manisha Priyadarshini et al.
MATERIALS AND MANUFACTURING PROCESSES (2019)
Experimental investigations on nano powder mixed Micro-Wire EDM process of inconel-718 alloy
P. Sivaprakasam et al.
MEASUREMENT (2019)
An innovation approach of multiple discharging channels in EDM precision machining by a novel adaptive gap voltage control system
Xin Mu et al.
2018 INTERNATIONAL SEMINAR ON COMPUTER SCIENCE AND ENGINEERING TECHNOLOGY (SCSET 2018) (2019)
Multi-objective Optimization of a Hybrid Machining Process Abrasive Powder Mixed WEDM of Inconel 718 using Particle Swarm Optimization Technique
A. Ranjan et al.
MATERIALS TODAY-PROCEEDINGS (2019)
Surface modification of WC-Co alloy using Al and Si powder through WEDM: A thermal erosion process
Vinod Kumar et al.
PARTICULATE SCIENCE AND TECHNOLOGY (2018)
Multi-channel aerosol dielectric electrical discharge machining ablation based on discrete electrode
Xiaochun Yu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Increasing process efficiency of HSWEDM based on discharge probability detection
Xiaoxiao He et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
WEDM of nickel based aerospace alloy: optimization of process parameters and modelling
Vinod Kumar et al.
INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM (2017)
Microcosmic mechanism of electrical discharge machining ablation on titanium alloy
Wang Xiangzhi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Study of the mechanism of multi-channel discharge in semiconductor processing by WEDM
Hao-ran Chen et al.
MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2015)
Effect of adding SiC powder on surface quality of quartz glass microslit machined by WECDM
Kuan Yuan Kuo et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Research on the influence of dielectric characteristics on the EDM of titanium alloy
Xiangzhi Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Mechanism of Electrical Discharge Machining Ablation
Xiangzhi Wang et al.
MATERIALS AND MANUFACTURING PROCESSES (2014)
An integrated systematic investigation of the process variables on surface generation in abrasive flow machining of titanium alloy 6Al4V
Mitchell Howard et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2014)
Experimental investigation, intelligent modeling and multi-characteristics optimization of dry WEDM process of Al-SiC metal matrix composite
Reza Kashiry Fard et al.
JOURNAL OF MANUFACTURING PROCESSES (2013)
Influence of workpiece circumferential speed in wire electrical discharge machining
E. Weingaertner et al.
PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM) (2013)
Analysis of electromagnetic force in wire-EDM
Shunsuke Tomura et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2009)
Near dry electrical discharge machining
C. C. Kao et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Parametric optimisation of wire electrical discharge machining of gamma titanium aluminide alloy through an artificial neural network model
S Sarkar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2006)
The application of research on powder mixed EDM in rough machining
WS Zhao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
Study of added powder in kerosene for the micro-slit machining of titanium alloy using electro-discharge machining
HM Chow et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
分享论文
