相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Non-polynomial framework for stress and strain response of the FG-GPLRC disk using three-dimensional refined higher-order theory
M. S. H. Al-Furjan et al.
ENGINEERING STRUCTURES (2021)
Additive manufacturing of a functionally graded material from Inconel625 to Ti6Al4V by laser synchronous preheating
Wei Meng et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Additive manufacturing of functionally graded Co-Fe and Ni-Fe magnetic materials
Varun Chaudhary et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Thermal induced phase evolution of Fe-Fe3Ni functionally graded material fabricated using the wire-arc additive manufacturing process: An in-situ neutron diffraction study
Chen Shen et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Additive manufacturing of composite materials and functionally graded structures using selective heat melting technique
Kalaimani Markandan et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)
Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing
Yi Su et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Tri-layered functionally graded membrane for potential application in periodontal regeneration
Asma Tufail Shah et al.
MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2019)
Additive manufacturing of functionally graded materials: A review
Chi Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Hardness, wear resistance and bonding strength of nano structured functionally graded Ni-Al2O3 composite coatings fabricated by ball milling method
Arash Yazdani et al.
ADVANCED POWDER TECHNOLOGY (2018)
Strength and Performance Enhancement of Multilayers by Spatial Tailoring of Adherend Compliance and Morphology via Multimaterial Jetting Additive Manufacturing
Jabir Ubaid et al.
SCIENTIFIC REPORTS (2018)
Determination of microstructure and mechanical properties of VC/Cr3C2 reinforced functionally graded WC-TiC-Al2O3 micro-nano composite tool materials via two-step sintering
Jialin Sun et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
A new process for design and manufacture of tailor-made functionally graded composites through friction stir additive manufacturing
Abhay Sharma et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Laser additive processing of a functionally graded internal fracture fixation plate
D. D. Lima et al.
MATERIALS & DESIGN (2017)
Multilayer graphene reinforced functionally graded tungsten carbide nano-composites
Jialin Sun et al.
MATERIALS & DESIGN (2017)
Theoretical model of adhesively bonded single lap joints with functionally graded adherends
William E. Guin et al.
ENGINEERING STRUCTURES (2016)
Functionally graded doped lanthanum cobalt ferrite and ceria-based composite interlayers for advancing the performance stability in solid oxide fuel cell
Koyel Banerjee Ghosh et al.
JOURNAL OF POWER SOURCES (2016)
Enhancement of strain tolerance of functionally graded LaTi2Al9O19 thermal barrier coating through ultra-short pulse based laser texturing
S. R. Dhineshkumar et al.
SURFACE & COATINGS TECHNOLOGY (2016)
Microstructural evaluation of a slurry based Ni/YSZ thermal barrier coating for automotive turbocharger turbine application
Muhammad Rabiu Abbas et al.
MATERIALS & DESIGN (2016)
Effect of La2Zr2O7 coat on the hot corrosion of multi-layer thermal barrier coatings
S. M. Naga et al.
MATERIALS & DESIGN (2016)
Functionally graded materials: A review of fabrication and properties
Minoo Naebe et al.
APPLIED MATERIALS TODAY (2016)
A critical review of recent research on functionally graded plates
D. K. Jha et al.
COMPOSITE STRUCTURES (2013)
Energy release rate for interlaminar cracks in graded laminates
Ulaganathan Jagan et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2008)
Mechanical behavior of functionally graded material plates under transverse load - Part II: Numerical results
Shyang-Ho Chi et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2006)
Thermal residual stresses in an adhesively-bonded functionally graded single-lap joint
M. Kemal Apalak et al.
JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2006)
Investigation of elastic stresses in an adhesively bonded single lap joint with functionally graded adherends in tension
MK Apalak et al.
COMPOSITE STRUCTURES (2005)
Interface crack between two shear deformable elastic layers
JL Wang et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2004)
Mechanics and fracture of crack tip deformable bi-material interface
PZ Qiao et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2004)
Biocompatibility of materials and development to functionally graded implant for bio-medical application
F Watari et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2004)
On the energy release rate and mode mix of delaminated shear deformable composite plates
HL Wang et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2004)
Functionally graded materials for sensor and energy applications
E Müller et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Boundary element analysis of crack problems in functionally graded materials
ZQ Yue et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2003)
Investigation of crack growth in functionally graded materials using digital image correlation
J Abanto-Bueno et al.
ENGINEERING FRACTURE MECHANICS (2002)
Exact solutions for stresses in functionally graded pressure vessels
N Tutuncu et al.
COMPOSITES PART B-ENGINEERING (2001)
分享论文
