相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Tribological study of Ti3SiC2/Cu5Si/TiC reinforced Co-based coatings on SUS304 steel by laser cladding
Gang Wang et al.
SURFACE & COATINGS TECHNOLOGY (2022)
Highly conductive wear resistant Cu/Ti3SiC2(TiC/SiC) co-continuous composites via vacuum infiltration process
Dexuan Yang et al.
JOURNAL OF ADVANCED CERAMICS (2020)
Investigation of the usage possibility of CuO and CuS thin films produced by successive ionic layer adsorption and reaction (SILAR) as solid lubricant
Halim Kovaci et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Influence of Cu on the mechanical and tribological properties of Ti3SiC2
Wentao Dang et al.
CERAMICS INTERNATIONAL (2016)
High Temperature Lubricating Behavior of NiAl Matrix Composites With Addition of CuO
Shengyu Zhu et al.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2016)
Interface structure and wetting behaviour of Cu/Ti3SiC2 system
J. R. Lu et al.
ADVANCES IN APPLIED CERAMICS (2015)
Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures
Shengyu Zhu et al.
WEAR (2012)
Surface strengthening of Ti3SiC2 through magnetron sputtering Cu and subsequent annealing
Haiping Guo et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2008)
Effect of TiC content on the microstructure and properties of Ti3SiC2-TiC composites in situ fabricated by spark plasma sintering
Jianfeng Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Tribological behavior of Ti3SiC2 sliding against Ni-based alloys at elevated temperatures
Shufang Ren et al.
TRIBOLOGY LETTERS (2008)
Effect of vacuum annealing on the phase stability of Ti3SiC2
It Meng Low et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2007)
Oxide-film-dependent tribological behaviors of Ti3SiC2
Zhenying Huang et al.
WEAR (2007)
Improving the surface hardness and wear resistance of Ti3SiC2 by boronizing treatment
C. Li et al.
SURFACE & COATINGS TECHNOLOGY (2007)
Microstructure and mechanical strength of diffusion-bonded Ti3SiC2/Ni joints
X. H. Yin et al.
JOURNAL OF MATERIALS RESEARCH (2006)
Depth profiling of phase composition in a novel Ti3SiC2-TiC system with graded interfaces
IM Low
MATERIALS LETTERS (2004)
Micron-scale deformation and damage mechanisms of Ti3SiC2 crystals induced by indentation
ZF Zhang et al.
ADVANCED ENGINEERING MATERIALS (2004)
Oxidation layer in sliding friction surface of high-purity Ti3SiC2
HX Zhai et al.
JOURNAL OF MATERIALS SCIENCE (2004)
Mechanical properties of Ti3SiC2 particulate reinforced copper prepared by hot pressing of copper coated Ti3SiC2 and copper powder
Y Zhou et al.
MATERIALS SCIENCE AND TECHNOLOGY (2004)
Chemical reaction and stability of Ti3SiC2 in Cu during high-temperature processing of Cu/Ti3SiC2 composites
YC Zhou et al.
ZEITSCHRIFT FUR METALLKUNDE (2004)
Oxidation behavior of Ti3SiC2 at high temperature in air
SB Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Oxidation behaviour of Ti3SiC2-based ceramic at 900-1300°C in air
ZM Sun et al.
CORROSION SCIENCE (2001)
Reaction of Al with Ti3SiC2 in the 800-1000°C temperature range
T El-Raghy et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)
Effect of grain size on friction and wear behavior of Ti3SiC2
T El-Raghy et al.
WEAR (2000)
分享论文
