☆ 4.7 Article

Friction spot extrusion brazing of copper to AISI 304 stainless steel with Zn interlayer: effect of shoulder surface modification

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Manufacturing

The influence of the backing plate materials on microstructure and mechanical properties of friction spot extrusion brazing of AA2024-T3 aluminum alloy and Brass sheets

Moslem Paidar et al.

Summary: The study investigated the impact of backing plate materials on microstructural and mechanical features during friction spot extrusion brazing. Results showed that changing the backing plate material significantly affected the microstructure of the reaction layers at the interface of the joint. The use of a Zn interlayer was found to restrict the creation of deleterious intermetallic compounds at the interface. Additionally, welds produced by steel backing plates showed a 35% increase in fracture load compared to those produced by copper backing plates, attributed to good metallurgical bonding and a larger amount of Al-Zn eutectic phase in the brazed zone.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of shoulder diameter on interfacial microstructure and mechanical behavior in dieless friction stir riveting of CP-Copper to 321 stainless steel

Guangli Fan et al.

Summary: This study found that increasing the tool shoulder diameter can enhance the temperature and tensile-shear load of the joints, and improve the metallurgical bonding of materials. A wider tool shoulder diameter helps prevent sheet bulging in the riveted zone and reduces the occurrence of defects.

VACUUM (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Weldability and mechanical properties of AA5083-H112 aluminum alloy and pure copper dissimilar friction spot extrusion welding-brazing

M. Paidar et al.

Summary: The friction spot extrusion welding-brazing (FSEW-B) process was used to join AA5083-H112 aluminum alloy and pure Cu with the help of a Zn interlayer to improve mechanical properties of the dissimilar joint. The data showed that FSEW-B eliminated keyhole defects and reduced brittle intermetallic compounds (IMCs) at the Cu/Al interface, resulting in improved strength and ductility of the weld sample.

VACUUM (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of material positioning during modified friction stir clinching brazing of Al/Zn/Cu welds

Moslem Paidar et al.

Summary: The study evaluated the influence of material positioning on the metallurgical and mechanical properties of Cu/Al and Al/Cu MFSCB joints with the use of Zn as interlayer. The results showed that material positioning significantly affected the quality of the joints, with a significant improvement in the performance of the joint when pure copper was placed on top of AA5083 in condition #1.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modified friction stir clinching of AA6061-T6/AA5754-O joint: Effect of tool rotational speed and solution heat treatment on mechanical, microstructure, and fracture behaviors

M. Paidar et al.

Summary: The mechanical properties of the improved heat-treated AA6061-T6/AA5754-O aluminum joints were enhanced by adjusting the tool rotational speed and applying a heat treatment process, which successfully reduced unbonded regions and increased the load-bearing capacity of the joints.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interfacial properties of friction stir lap welded 430/304 stainless steels using Cu interlayer

Guolin Guo et al.

Summary: Friction stir lap welding of dissimilar stainless steels 304 and 430 was successfully achieved using a Cu interlayer, where different metallurgical processes were utilized at the interfaces. The Cu interlayer promoted atom diffusion and reduced interfacial stress, leading to a significant improvement in joint performance.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Friction spot extrusion welding-brazing of copper to aluminum alloy

M. Paidar et al.

Summary: Changing the shoulder geometry in friction spot extrusion welding-brazing can increase the tensile/shear strength of the joint, attributed to the larger brazed zone and complete filling of the pre-threaded hole.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dieless Friction Stir Extrusion-Brazing (DFSE-B) of AA2024-T3 aluminum alloy to Copper with Zn interlayer

M. Paidar et al.

Summary: The study demonstrated the improved load-bearing performance of dissimilar AA2024-T3/copper joint using Dieless Friction Stir Extrusion-Brazing (DFSE-B), compared with Friction Stir Spot Welding-Brazing (FSSW-B). The DFSE-B process suppresses flow-induced defects, resulting in enhanced tensile-shear load and toughness due to the absence of tool-induced keyhole and mechanical interlocking of softer Al alloy into harder Cu alloy. DFSE-B proves to be a suitable welding alternative for reactive metals.

RESULTS IN PHYSICS (2021)

添加到收藏夹

Article Engineering, Civil

Investigation of modified friction stir clinching-brazing process of AA2024 Al/AZ31 Mg: metallurgical and mechanical properties

Moslem Paidar et al.

Summary: The weldability of AA2024-T3 and AZ31 Mg alloys was investigated using two processes, MFSC-B and PFSSB. The MFSC-B process showed better material flow and higher dislocation density, leading to improved tensile/shear failure load. Therefore, it is recommended for dissimilar joining of Mg and Al alloys.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

添加到收藏夹

Article Engineering, Manufacturing

Friction welding of dissimilar joints copper-stainless steel pipe consist of 0.06 wall thickness to pipe diameter ratio

Hardik D. Vyas et al.

Summary: The study found that dissimilar friction welding between ETP-Cu and SS of grade 304 L can produce strong joints with excellent leak-proof ability and strength, with noticeable microstructure changes on the Cu side but not on the SS side. The continuity of welding was observed at the periphery of the pipe configuration with the presence of a continuous reaction layer containing Cu and Fe elements at the joint interface.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Optics

Porosity and liquation cracking of dissimilar Nd:YAG laser welding of SUS304 stainless steel to T2 copper

Jianmin Li et al.

OPTICS AND LASER TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Manufacturing

Dieless friction stir lap joining of AA 5050-H32 with AA 6061-T6 at varying pre-drilled hole diameters

Tinu P. Saju et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Article Engineering, Civil

Effect of shoulder features during friction spot extrusion welding of 2024-T3 to 6061-T6 aluminium alloys

Jinzhen Han et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2020)

添加到收藏夹

Article Engineering, Manufacturing

MIG-TIG double-sided arc welding of copper-stainless steel using different filler metals

Zhi Cheng et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Modified friction stir clinching of 2024-T3 to 6061-T6 aluminium alloy: Effect of dwell time and precipitation-hardening heat treatment

M. Paidar et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Optics

Prediction of weld geometry, temperature contour and strain distribution in disk laser welding of dissimilar joining between copper & 304 stainless steel

M. Aghaee Attar et al.

OPTIK (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Cracking of Copper Brazed Steel Joints Due to Precipitation of MnS upon Cooling

Dheeraj Varanasi et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microscopic appraisal and mechanical behavior of hybrid Cu/Al joints fabricated via friction stir spot welding-brazing and modified friction stir clinching-brazing

Lian Tong et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Texture mapping in electron beam welded dissimilar copper-stainless steel joints by neutron diffraction

Soumitra Kumar Dinda et al.

VACUUM (2020)

添加到收藏夹

Article Engineering, Mechanical

Effect of pinless tool shoulder diameter on dieless friction stir extrusion joining of AA 5052-H32 and AA 6061-T6 aluminum alloy sheets

Tinu P. Saju et al.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of sandwich copper/steel composites produced by explosive welding

S. V. Gladkovsky et al.

MATERIALS CHARACTERIZATION (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Towards attaining dissimilar lap joint of CuCrZr alloy and 316L stainless steel using friction stir welding

Pankaj Sahlot et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2018)

添加到收藏夹

Article Engineering, Mechanical

Microstructures and mechanical properties of friction stir welded dissimilar steel-copper joints

M. Jafari et al.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Understanding the role of welding parameters and tool profile on the morphology and properties of expelled flash of spot welds

Ojo Olatunji Oladimeji et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interfacial microstructure and properties of copper clad steel produced using friction stir welding versus gas metal arc welding

Z. Shen et al.

MATERIALS CHARACTERIZATION (2015)

添加到收藏夹

Article Automation & Control Systems

Interfacial characterization of T3 copper/35CrMnSi steel dissimilar metal joints by inertia radial friction welding

Ying Wang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)

添加到收藏夹

Article Engineering, Industrial

Radial friction welding interface between brass and high carbon steel

Jian Luo et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.