☆ 4.7 Article

Modeling Spring-In of L-Shaped Structural Profiles Pultruded at Different Pulling Speeds

POLYMERS (2021)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Mechanics

Effects of pulling speed on structural performance of L-shaped pultruded profiles

Alexander Vedernikov et al.

Summary: This study analyzed the influence of pulling speed on the structural characteristics of pultruded glass fiber/epoxy-vinyl resin composite profiles. The results showed that an increase in pulling speed led to an increase in spring-in angle, affecting the mechanical properties of the profiles. Profiles produced at different pulling speeds exhibited differences in cracking and mechanical characteristics.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Numerical and experimental analysis of resin-flow, heat-transfer, and cure in a resin-injection pultrusion process

Michael Sandberg et al.

Summary: This paper investigates non-isothermal flow in a thermoset resin-injection pultrusion process, highlighting phase transitions of both concave and convex shapes due to the heating configuration and convective flow near inlets, which differs from existing literature that commonly describes phase transitions initiated from die-walls.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Mechanics

A simulation framework for predicting process-induced distortions for precise manufacturing of aerospace thermoset composites

Neoklis Traiforos et al.

Summary: The study compares the performance of the CHILE model and a linear viscoelastic material model in predicting process induced distortions in aerospace composite frames. By integrating cure kinetics model, chemical shrinkage model, and using a generalized Maxwell model to model the resin's viscoelastic behavior, it is shown that the viscoelastic model more accurately predicts distortions.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Quantifying effects of manufacturing methods on fiber orientation in unidirectional composites using structure tensor analysis

N. Jeppesen et al.

Summary: The properties of fiber-reinforced composites are sensitive to fiber alignment. By analyzing fiber orientations in different samples using structure tensor analysis on CT images, it was found that misaligned fibers can be minimized by adjusting production parameters. The study provides insights for manufacturers to optimize the alignment of fibers in composite materials.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Engineering, Civil

Experimental, analytical and numerical investigation of pultruded GFRP composite beams infilled with hybrid FRP reinforced concrete

Lokman Gemi et al.

Summary: This paper presents experimental, analytical, and numerical analyses on the behavior of pultruded GFRP composite beams infilled with hybrid fiber reinforced concrete under four-point loading. The study found that the pultruded profile and composite wrapping significantly improved the performance of the beams, with hybrid reinforcements being recommended for all cases. Detailed damage analyses were also provided.

ENGINEERING STRUCTURES (2021)

添加到收藏夹

Review Polymer Science

Thermoplastic Pultrusion: A Review

Kirill Minchenkov et al.

Summary: This overview examines the use of thermoplastic composites in pultrusion processes in order to analyze the existing gap between thermoset and thermoplastic pultrusions and promote the development of the latter. By investigating the processes, raw materials, and applications of thermoplastic pultrusion, this study aims to identify current issues and propose future research directions for thermoplastic pultrusion.

POLYMERS (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Material characterization of a pultrusion specific and highly reactive polyurethane resin system: Elastic modulus, rheology, and reaction kinetics

Onur Yuksel et al.

Summary: This study characterized the chemical behavior, cure kinetics, and viscosity evolution of a polyurethane resin system for pultrusion. The gelation point was estimated from the cross-over point of storage and loss modulus curves, and the corresponding cure degree was determined using a cure kinetics model. DMA was used to measure the elastic modulus and glass transition temperature of fully and partially cured samples. A five-step cure hardening model was well fitted to a wide range of cure degree values after gelation. These material models were then applied to a case study of a typical pultrusion process to study the effects of pulling speed on material property evolution.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Engineering, Civil

Static behaviour of glass fibre reinforced novel composite sleepers for mainline railway track

Wahid Ferdous et al.

Summary: This study proposed three new railway sleeper concepts and evaluated them experimentally and numerically. The results show that these new concepts have the potential to replace traditional wooden railway sleepers in terms of structural performance and commercial viability.

ENGINEERING STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Modelling hollow pultruded FRP pro fi les under axial compression: Local buckling and progressive failure

Mohammad Alhawamdeh et al.

Summary: This paper presents a numerical study on the local buckling and compressive failure of hollow PFRP profiles under axial compression, using the Newton method and adaptive stabilisation scheme in Abaqus 2019. The numerical predictions were validated by experiments. The energy parameters and constituent failure modes were used to explain the effects of dimension, layup, and slenderness ratio on the post-peak behavior and failure modes of the PFRP profiles.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Materials modelling and process simulation of the pultrusion of curved parts

G. Struzziero et al.

Summary: This paper explores the simulation of manufacturing aerospace quality carbon/epoxy composite curved parts using pultrusion. By partially curing in a pre-former and final curing in a curved post-former, the process ensures the success of manufacturing a T-stiffener. Simulation results demonstrate the feasibility of the process without inducing defects.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Materials Science, Composites

Effects of additives on the cure kinetics of vinyl ester pultrusion resins

Alexander Vedernikov et al.

Summary: This study focuses on investigating the cure kinetics modeling of a vinyl ester pultrusion resin. By comparing 16 kinetic models, a model based on the n th-order autocatalytic reaction was found to have the best performance, with a proposed method to reduce errors resulting from simultaneous melting of additives. The research also demonstrates the significant influence of resin composition on the manufacturing process of composite materials.

JOURNAL OF COMPOSITE MATERIALS (2021)

添加到收藏夹

Article Mechanics

Axial compression behaviour of all-composite modular wall system

Arvind Sharda et al.

Summary: The study evaluated the structural behavior of modular wall systems made from pultruded glass fiber reinforced polymer profile and composite sheathings. Results showed that composite wall systems with extended studs were ten times stiffer and stronger than walls with extended plates, demonstrating a high potential for fiber composite materials in modular wall systems.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Effect of elevated temperatures on the compressive behavior of timber filled steel and pultruded GFRP tubes

Mohammad Shekarchi et al.

Summary: The study explored the use of timber as a filler material for steel and pultruded GFRP tube elements, finding that timber-filled tubes could significantly improve compressive strength and stiffness. Timber-filled steel tubes and hollow steel tubes exhibited better performance at elevated temperatures, while timber-filled pultruded GFRP tubes experienced significant strength and stiffness loss beyond resin transition and decomposition temperatures. Novel empirical models accurately predicted compressive strength and stiffness of filled tubes under various temperature conditions.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Study on cure-induced residual stresses and spring-in deformation of L-shaped composite laminates using a simplified constitutive model considering stress relaxation

Xiaodong Liu et al.

Summary: A simplified constitutive model of resin in curing process considering stress relaxation was proposed in this paper, which improves computational efficiency while maintaining accuracy, addressing a practical need. The model was used to predict spring-in deformations of composite laminates with different structural parameters, showing good agreement with experiments. Additionally, a new interpretation of residual stress and spring-in deformation mechanisms was presented based on strain and stress changes, highlighting the importance of considering stress relaxation in modeling.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

A hybrid beam-column element for direct second-order nonlinear analysis of PFRP frame structures

Ruijie Zhu et al.

Summary: A novel imperfect nonlinear beam-column element considering the unique characteristics of PFRP profiles was proposed for accurate structural calculation of PFRP space frame structures. The element incorporates the effects of joint stiffness, rigid arm, and reinforcement segment without increasing external degrees of freedom, showing advantages of easy structural modeling and high computational efficiency.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Bearing strength and failure behaviour of composite pre-tightened multi-tooth joint

Yifeng Gao et al.

Summary: The study investigated the bearing strength and failure behavior of a new composite pre-tightened multi-tooth joint, finding that the bearing capacity increased with the pre-tightening force, tooth depth, tooth length, and number of teeth. Four typical failure modes were identified, and the numerical model was effective in predicting the joint's strength and behavior.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Moisture effect on shape distortions of curved quasi-isotropic prepreg composite laminates

Erik Horberg et al.

Summary: Moisture has a significant impact on the shape distortion of curved thermoset composite laminates, and needs to be carefully controlled and considered during experiments. By analyzing the experimental results, a relationship between the bracket angle, specimen thickness, and moisture content has been established.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Steady-state modelling and analysis of process-induced stress and deformation in thermoset pultrusion processes

Michael Sandberg et al.

Summary: This paper introduces a new numerical framework that speeds up calculations and demonstrates modeling methods for two critical factors in composite profile manufacturing processes. The research shows that pulling force can advance die detachment and reduce swelling, while the initial compressive stress state has the opposite but more significant effect.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Engineering, Civil

Influence of heat damage on the bolted double lap joint strength of pultruded E-glass/polyester composites

Elias A. Toubia et al.

Summary: This experimental study evaluates the residual strengths and failure mechanisms of bolted double lap pultruded joints in regions of low-to-moderate heat induced exposure, finding that plate thickness and load direction are key parameters influencing the residual strength and failure modes of thermally degraded pultruded joints.

THIN-WALLED STRUCTURES (2021)

添加到收藏夹

Article Chemistry, Physical

Mesoscale Process Modeling of a Thick Pultruded Composite with Variability in Fiber Volume Fraction

Onur Yuksel et al.

Summary: This study characterized the variability in fiber volume fraction (Vf) in pultruded profiles and incorporated this nonuniformity into a process model. The results demonstrated that nonuniformity in Vf distribution can increase the absolute magnitude of residual stress, leading to a more scattered residual stress distribution.

MATERIALS (2021)

添加到收藏夹

Article Engineering, Manufacturing

Experimental and numerical investigation of reduction in shape distortion for angled composite parts

Khubab Shaker et al.

INTERNATIONAL JOURNAL OF MATERIAL FORMING (2020)

添加到收藏夹

Article Mechanics

Modeling of cracking during pultrusion of large-size profiles

Alexander Safonov et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Mechanics

Experimental and Theoretical Investigation on Flexure Performance of Pultruded GFRP Composite Beams with Damage Analyses

Emrah Madenci et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Materials Science, Composites

Measurement of flexible components in composite material by a 3-2-1 locating scheme

Andrea Corrado et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Composites

Cure-induced residual stresses for warpage reduction in thermoset laminates

Giacomo Struzziero et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

添加到收藏夹

Review Engineering, Marine

Marine Application of Fiber Reinforced Composites: A Review

Felice Rubino et al.

JOURNAL OF MARINE SCIENCE AND ENGINEERING (2020)

添加到收藏夹

Review Materials Science, Composites

Pultruded materials and structures: A review

Alexander Vedernikov et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

添加到收藏夹

Article Mechanics

Buckling and free vibration analyses of pultruded GFRP laminated composites: Experimental, numerical and analytical investigations

Emrah Madenci et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Mechanics

Mechanical property evolution and service life prediction of pultruded carbon/glass hybrid rod exposed in harsh oil -well condition

Chenggao Li et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Mechanics

Effect of bearing length on web crippling behavior of pultruded GFRP channel section

Chao Wu et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Engineering, Civil

Predicting Flange Local Buckling Capacity of Pultruded GFRP I-Sections Subject to Flexure

Tianqiao Liu et al.

JOURNAL OF COMPOSITES FOR CONSTRUCTION (2020)

添加到收藏夹

Article Chemistry, Physical

Modelling of Process-Induced Deformation for Composite Parts Considering Tool-Part Interaction

Wei Qiao et al.

MATERIALS (2020)

添加到收藏夹

Article Mechanics

Treed gaussian process for manufacturing imperfection identification of pultruded GFRP thin-walled profile

Marco Civera et al.

COMPOSITE STRUCTURES (2020)

添加到收藏夹

Article Engineering, Manufacturing

A fully coupled thermo-mechanical analysis for the minimisation of spring-in and process time in ultra-thick components for wind turbine blades

G. Struzziero et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)

添加到收藏夹

Article Engineering, Civil

Compression Behavior of Square Pyramid Substructure of Novel Pultruded FRP-Aluminum Space Truss

Ruijie Zhu et al.

JOURNAL OF COMPOSITES FOR CONSTRUCTION (2020)

添加到收藏夹

Article Mechanics

Investigation of fast curing epoxy resins regarding process induced distortions of fibre reinforced composites

Fabian Groh et al.

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Article Polymer Science

Impact of nanoparticles on the process-induced distortions of carbon fiber reinforced plastics: An experimental and simulative approach

Wibke Exner et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2019)

添加到收藏夹

Article Mechanics

Thickness effect on spring-in of prepreg composite L-profiles - An experimental study

Erik Horberg et al.

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Article Materials Science, Composites

A new analytical solution for cure-induced spring-in of L-shaped composite parts

Anxin Ding et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2019)

添加到收藏夹

Article Engineering, Mechanical

Tension-tension fatigue performance of a large-diameter pultruded carbon/glass hybrid rod

Chenggao Li et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Mechanics

3D topology optimization of continuous fiber-reinforced structures via natural evolution method

Alexander A. Safonov

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Review Engineering, Manufacturing

Numerical optimisation of thermoset composites manufacturing processes: A review

G. Struzziero et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)

添加到收藏夹

Review Mechanics

Mathematical simulation of pultrusion processes: A review

Alexander A. Safonov et al.

COMPOSITE STRUCTURES (2018)

添加到收藏夹

Article Materials Science, Composites

Geometrical deviation analysis of CFRP thin laminate assemblies: Numerical and experimental results

Andrea Corrado et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2018)

添加到收藏夹

Article Materials Science, Composites

Characterisation and modelling of thermal expansion coefficient of woven carbon/epoxy composite and its application to the determination of spring-in

Yasir Nawab et al.

JOURNAL OF COMPOSITE MATERIALS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

ANSYS-based algorithms for a simulation of pultrusion processes

Evgeny Barkanov et al.

MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2017)

添加到收藏夹

Article Engineering, Manufacturing

Process-induced strain and distortion in curved composites. Part I: Development of fiber-optic strain monitoring technique and analytical methods

Kazunori Takagaki et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)

添加到收藏夹

Article Mechanics

Monitoring the gelation and effective chemical shrinkage of composite curing process with a novel FBG approach

Haixiao Hu et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Engineering, Mechanical

Design Otimization of Tuss Bidge Sructures of Cmposite Mterials

D. V. Tinkov et al.

JOURNAL OF MACHINERY MANUFACTURE AND RELIABILITY (2017)

添加到收藏夹

Article Engineering, Manufacturing

Chemical and thermal shrinkage in thermosetting prepreg

Oleksandr G. Kravchenko et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)

添加到收藏夹

Review Construction & Building Technology

Composite piles: A review

Kujtim Zyka et al.

CONSTRUCTION AND BUILDING MATERIALS (2016)

添加到收藏夹

Article Mechanics

Closed form expression for residual stresses and warpage during cure of composite laminates

M. Abouhamzeh et al.

COMPOSITE STRUCTURES (2015)

添加到收藏夹

Article Materials Science, Composites

A comparative experiment for the analysis of microwave and thermal process induced strains of carbon fiber/bismaleimide composite materials

Nanya Li et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Composites

Mechanical Modelling of Pultrusion Process: 2D and 3D Numerical Approaches

Ismet Baran et al.

APPLIED COMPOSITE MATERIALS (2015)

添加到收藏夹

Article Materials Science, Composites

Compaction influence on spring-in of thin composite parts: Experimental and numerical results

L. Sorrentino et al.

JOURNAL OF COMPOSITE MATERIALS (2015)

添加到收藏夹

Article Mechanics

Modelling the pultrusion process of an industrial L-shaped composite profile

Ismet Baran et al.

COMPOSITE STRUCTURES (2014)

添加到收藏夹

Article Mechanics

Process distortions in prepreg manufacturing - An experimental study on CFRP L-profiles

E. Kappel et al.

COMPOSITE STRUCTURES (2013)

添加到收藏夹

Article Engineering, Multidisciplinary

Process induced residual stresses and distortions in pultrusion

Ismet Baran et al.

COMPOSITES PART B-ENGINEERING (2013)

添加到收藏夹

Article Thermodynamics

Computational Approaches for Modeling the Multiphysics in Pultrusion Process

P. Carlone et al.

ADVANCES IN MECHANICAL ENGINEERING (2013)

添加到收藏夹

Article Engineering, Manufacturing

Modelling of the spring-in phenomenon in curved parts made of a thermosetting composite

Nuri Ersoy et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)

添加到收藏夹

Article Materials Science, Composites

Characterization Methodology of Thermoset Resins for the Processing of Composite Materials - Case Study: CYCOM 890RTM Epoxy Resin

Lolei Khoun et al.

JOURNAL OF COMPOSITE MATERIALS (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Poisson's ratio of hollow particle filled composites

Ronald Poveda et al.

MATERIALS LETTERS (2010)

添加到收藏夹

Article Engineering, Mechanical

Pecularities of Using Carbon Glass-Reinforced Plastic in Pultrusion Composite Profiles for Bridge Engineering

T. G. Sorina et al.

JOURNAL OF MACHINERY MANUFACTURE AND RELIABILITY (2010)

添加到收藏夹

Article Engineering, Manufacturing

Closed-form solution for process-induced stresses and deformation of a composite part cured on a solid tool: Part II - Curved geometries

Abdul Rahim Ahamed Arafath et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2009)

添加到收藏夹

Article Engineering, Manufacturing

Quantitation of the reinforcement effect of silica nanoparticles in epoxy resins used in liquid composite moulding processes

T. Mahrholz et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2009)

添加到收藏夹

Article Engineering, Mechanical

Optimization of the Pultrusion Process for a Rod with a Large Diameter

A. A. Safonov et al.

JOURNAL OF MACHINERY MANUFACTURE AND RELIABILITY (2009)

添加到收藏夹

Article Engineering, Manufacturing

Investigation on the spring-in phenomenon of carbon nanofiber-glass fiber/polyester composites manufactured with vacuum assisted resin transfer molding

Kuang-Ting Hsiao et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)

添加到收藏夹

Article Materials Science, Composites

Shear-lag analysis of the effect of thickness on spring-in of curved composites

Michael R. Wisnom et al.

JOURNAL OF COMPOSITE MATERIALS (2007)

添加到收藏夹

Article Engineering, Manufacturing

Cure shrinkage characterization and modeling of a polyester resin containing low profile additives

Mohsan Haider et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2007)

添加到收藏夹

Article Engineering, Manufacturing

Mechanisms generating residual stresses and distortion during manufacture of polymer-matrix composite structures

MR Wisnom et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)

添加到收藏夹

Article Engineering, Manufacturing

Multi-criteria thermal optimization in liquid composite molding to reduce processing stresses and cycle time

E Ruiz et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)

添加到收藏夹

Article Engineering, Manufacturing

Development of spring-in angle during cure of a thermosetting composite

N Ersoy et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2005)

添加到收藏夹

Article Engineering, Manufacturing

A linear finite element model to predict processing-induced distortion in FRP laminates

SK Bapanapalli et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2005)

添加到收藏夹

Article Engineering, Manufacturing

Prediction of shape distortions Part I. FE-implementation of a path dependent constitutive model

JM Svanberg et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2004)

添加到收藏夹

Article Engineering, Manufacturing

Prediction of shape distortions. Part II. Experimental validation and analysis of boundary conditions

JM Svanberg et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2004)

添加到收藏夹

Article Mechanics

Finite element based prediction of process-induced deformation of autoclaved composite structures using 2D process analysis and 3D structural analysis

G Fernlund et al.

COMPOSITE STRUCTURES (2003)

添加到收藏夹

Article Engineering, Chemical

Cure kinetics, gelation, and glass transition of a bisphenol F epoxide

DJ O'Brien et al.

POLYMER ENGINEERING AND SCIENCE (2003)

添加到收藏夹

Article Engineering, Manufacturing

Experimental and numerical study of the effect of cure cycle, tool surface, geometry, and lay-up on the dimensional fidelity of autoclave-processed composite parts

G Fernlund et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2002)

添加到收藏夹

Article Materials Science, Composites

Isolating components of processing induced warpage in laminated composites

DA Darrow et al.

JOURNAL OF COMPOSITE MATERIALS (2002)

添加到收藏夹

Article Materials Science, Composites

Spring-in and warpage of angled composite laminates

C Albert et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2002)

添加到收藏夹

Article Engineering, Multidisciplinary

On the properties of quasi-isotropic laminates

R Akkerman

COMPOSITES PART B-ENGINEERING (2002)

添加到收藏夹

Article Engineering, Manufacturing

An experimental investigation on mechanisms for manufacturing induced shape distortions in homogeneous and balanced laminates

JM Svanberg et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2001)

添加到收藏夹

Article Materials Science, Composites

Manufacture of fiber-reinforced composites by microwave assisted pultrusion

JM Methven et al.

POLYMER COMPOSITES (2000)

添加到收藏夹

Article Materials Science, Composites

Separating sources of manufacturing distortion in laminated composites

DW Radford et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2000)

添加到收藏夹

Article Materials Science, Composites

Finite element analysis of temperature induced stresses and deformations of polymer composite components

J Wang et al.

JOURNAL OF COMPOSITE MATERIALS (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.