相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Micro Deep Drawability of the Superplastic Zn-22Al Alloy at a High Strain Rate and Room Temperature
Mehmet Emin Cetin et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2020)
Analysis of size dependent earing evolution in micro deep drawing of TWIP steel by using crystal plasticity modeling
N. Guo et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)
Thin Film Encapsulation for RF MEMS in 5G and Modern Telecommunication Systems
Anna Persano et al.
SENSORS (2020)
Study of Wire Deformation Characterization and Size Effects during the Micro-Flat-Rolling Process
Haibo Xie et al.
METALS (2020)
Research on micro-deep drawing process of concial part with ultra-thin copper foil using multi-layered DLC film-coated die
C. J. Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Size effect on the yield behavior of metal foil under multiaxial stress states: Experimental investigation and modelling
C. Cheng et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)
Theories and experiments on effects of acoustic energy field in micro-square cup drawing
Chang-Li Zha et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
An investigation on the formability of sheet metals in the micro/meso scale hydroforming process
Zhutian Xu et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)
Development and performance analysis of a low-cost MEMS microphone-based hearing aid with three different audio amplifiers
Souvik Mallik et al.
INNOVATIONS IN SYSTEMS AND SOFTWARE ENGINEERING (2019)
The multi-physics analysis for a novel tool structure to improve the accuracy in electrochemical micro-machining
Weidong Liu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Micro deep drawing of T2 copper foil using proportional decreased tools
Guofeng Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Enhancing Localization Accuracy of MEMS-INS/GPS/In-Vehicle Sensors Integration During GPS Outages
Qimin Xu et al.
IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT (2018)
Investigation of Multimodal Electret-Based MEMS Energy Harvester With Impact-Induced Nonlinearity
Kai Tao et al.
JOURNAL OF MICROELECTROMECHANICAL SYSTEMS (2018)
MEMS-tunable dielectric metasurface lens
Ehsan Arbabi et al.
NATURE COMMUNICATIONS (2018)
Influence of size effect and plastic strain gradient on the springback behaviour of metallic materials in microbending process
J. L. Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Material selection for Micro-Electro-Mechanical-Systems (MEMS) using Ashby's approach
Zahid Mehmood et al.
MATERIALS & DESIGN (2018)
Micro-hydromechanical deep drawing of metal cups with hydraulic pressure effects
Liang Luo et al.
FRONTIERS OF MECHANICAL ENGINEERING (2018)
Evaluation of micro deep drawing technique using soft die-simulation and experiments
Ihsan K. Irthiea et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Forming limit of sheet metals in meso-scale plastic forming by using different failure criteria
L. F. Peng et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)
Tearing failure of ultra-thin sheet-metal involving size effect in blanking process: Analysis based on modified GTN model
Shen Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)
Study of micro flexible rolling based on grained inhomogeneity
Feijun Qu et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)
Drawability and size effects for micro-arrayed deep drawing of Ni-Co/GO nanocomposite foils
You Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Investigation of holder pressure and size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator
Iman Aminzahed et al.
MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2017)
Design, fabrication and characterization of flexible MEMS accelerometer using multi-Level UV-LIGA
Md. Sohel Mahmood et al.
SENSORS AND ACTUATORS A-PHYSICAL (2017)
Deformation behavior of materials in micro-forming with consideration of intragranular heterogeneities
Zhen-wu Ma et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2017)
Influences of micro-friction on surface finish in micro deep drawing of SUS304 cups
Liang Luo et al.
WEAR (2017)
Influence of tool geometry variations on the limiting drawing ratio in micro deep drawing
G. Behrens et al.
INTERNATIONAL JOURNAL OF MATERIAL FORMING (2016)
Effects of surface roughness on micro deep drawing of circular cups with consideration of size effects
Liang Luo et al.
FINITE ELEMENTS IN ANALYSIS AND DESIGN (2016)
Analysis of micro flexible rolling with consideration of material heterogeneity
Feijun Qu et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2016)
Laser 3D micro-manufacturing
Alberto Pique et al.
JOURNAL OF PHYSICS D-APPLIED PHYSICS (2016)
Experimental and numerical studies of coupling size effects on material behaviors of polycrystalline metallic foils in microscale plastic deformation
Haiming Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Effects of interfacial contact states on tribological behaviour in micro-sheet forming
Chunju Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2015)
Development of servo-type micro-hydromechanical deep-drawing apparatus and micro deep-drawing experiments of circular cups
H. Sato et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Influences of lubrication conditions and blank holder force on micro deep drawing of C1100 micro conical-cylindrical cup
Feng Gong et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2015)
Experimental and simulation studies of micro blanking and deep drawing compound process using copper sheet
M. W. Fu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Modeling and analysis of dry friction in micro-forming of metals
Wei Zheng et al.
TRIBOLOGY INTERNATIONAL (2013)
Size effects in micro cup drawing
A. Molotnikov et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Effects on the deep drawing diagram in micro forming
F. Vollertsen
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2012)
Micro deep drawing of micro cups by using DLC film coated blank holders and dies
Feng Gong et al.
DIAMOND AND RELATED MATERIALS (2011)
Realisation and application of size dependent FEM-simulation for deep drawing of rectangular work pieces
Zhenyu Hu
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2011)
Size Effects in Micro Forming
F. Vollertsen
SHEET METAL 2011 (2011)
Tribological size effects in sheet metal forming measured by a strip drawing test
F. Vollertsen et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2006)