相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Experimental detergent drying analysis in a counter-current spray dryer with swirling air flow
Pawel Wawrzyniak et al.
DRYING TECHNOLOGY (2020)
Numerical investigation of gas-particle hydrodynamics in a vortex chamber fluidized bed
Subhajit Dutta et al.
ADVANCED POWDER TECHNOLOGY (2018)
CFD modeling of a pilot-scale countercurrent spray drying tower for the manufacture of detergent powder
Muzammil Ali et al.
DRYING TECHNOLOGY (2017)
Experimental study of the application of rotating fluidized beds to particle separation
Justin M. Weber et al.
POWDER TECHNOLOGY (2017)
Experimentally validated numerical study of gas-solid vortex unit hydrodynamics
K. Niyogi et al.
POWDER TECHNOLOGY (2017)
Influence of solids outlets and the gas inlet design on the generation of a gas-solids rotating fluidized bed in a vortex chamber for different types of particles
Waldo Rosales Trujillo et al.
CHEMICAL ENGINEERING SCIENCE (2017)
Design and cold flow testing of a Gas-Solid Vortex Reactor demonstration unit for biomass fast pyrolysis
Arturo Gonzalez-Quiroga et al.
CHEMICAL ENGINEERING JOURNAL (2017)
Experimental study of paddy drying in a vortex chamber
Jnyana Ranjan Pati et al.
DRYING TECHNOLOGY (2016)
Qualitative numerical study of simultaneous high-G-intensified gas-solids contact, separation and segregation in a bi-disperse rotating fluidized bed in a vortex chamber
Juray De Wilde et al.
ADVANCED POWDER TECHNOLOGY (2016)
Modeling and simulation of biomass drying in vortex chambers
Philippe Eliaers et al.
CHEMICAL ENGINEERING SCIENCE (2015)
Gas-solid fluidized beds in vortex chambers
Juray De Wilde
CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2014)
High-G, low-temperature coating of cohesive particles in a vortex chamber
Philippe Eliaers et al.
POWDER TECHNOLOGY (2014)
Drying of Biomass Particles: Experimental Study and Comparison of the Performance of a Conventional Fluidized Bed and a Rotating Fluidized Bed in a Static Geometry
Philippe Eliaers et al.
DRYING TECHNOLOGY (2013)
Fluid catalytic cracking in a rotating fluidized bed in a static geometry: a CFD analysis accounting for the distribution of the catalyst coke content
Waldo Rosales Trujillo et al.
POWDER TECHNOLOGY (2012)
Rotating fluidized bed with a static geometry: Guidelines for design and operating conditions
Abhishek Dutta et al.
CHEMICAL ENGINEERING SCIENCE (2010)
A Study of Particle Histories during Spray Drying Using Computational Fluid Dynamic Simulations
C. Anandharamakrishnan et al.
DRYING TECHNOLOGY (2010)
Numerical investigation of gas-solid heat transfer in rotating fluidized beds in a static geometry
Axel de Broqueville et al.
CHEMICAL ENGINEERING SCIENCE (2009)
Modeling of Droplet Drying in Spray Chambers Using 2D and 3D Computational Fluid Dynamics
M. Mezhericher et al.
DRYING TECHNOLOGY (2009)
Continuous and Discrete Phase Behavior in Countercurrent Spray Drying Process
Ireneusz Zbicinski et al.
DRYING TECHNOLOGY (2009)
Experimental investigation of a rotating fluidized bed in a static geometry
Juray De Wilde et al.
POWDER TECHNOLOGY (2008)
A parametric study of spray drying of a solution in a pulsating high-temperature turbulent flow
Zhonghua Wu et al.
DRYING TECHNOLOGY (2006)
Numerical study of two-stage horizontal spray dryers using computational fluid dynamics
Lixin Huang et al.
DRYING TECHNOLOGY (2006)
Use of computational fluid dynamics to evaluate alternative spray dryer chamber configurations
LX Huang et al.
DRYING TECHNOLOGY (2003)
A parametric study of the gas flow patterns and drying performance of co-current spray dryer: Results of a computational fluid dynamics study
LX Huang et al.
DRYING TECHNOLOGY (2003)
Superheated steam dryer: simulations and experiments on product drying
F Ducept et al.
CHEMICAL ENGINEERING JOURNAL (2002)
分享论文
