相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Asynchronous Sampled-Data Filtering Design for Fuzzy-Affine-Model-Based Stochastic Nonlinear Systems
Jianbin Qiu et al.
IEEE TRANSACTIONS ON CYBERNETICS (2021)
A New Infrared Heat Treatment on Hot Forging 7075 Aluminum Alloy: Microstructure and Mechanical Properties
Yi-Ling Chang et al.
MATERIALS (2020)
A Combined Cold Extrusion for a Drive Shaft: A Parametric Study on Tool Geometry
Tae-Wan Ku
MATERIALS (2020)
Development of a non-isothermal forging process for hollow power transmission shafts
Hao Pang et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Comparing the Through-Thickness Gradient of the Deformed and Recrystallized Microstructure in Tantalum with Unidirectional and Clock Rolling
Jialin Zhu et al.
MATERIALS (2019)
A Coupled EBSD/TEM Analysis of the Microstructure Evolution of a Gradient Nanostructured Ferritic/Martensitic Steel Subjected to Surface Mechanical Attrition Treatment
Wenbo Liu et al.
MATERIALS (2019)
Finite Element Modeling of Shrink-Fit Design for Improvement of Die-Service Life in Hot Forging Process of a Bevel Gear
Panuwat Soranansri et al.
MATERIALS TODAY-PROCEEDINGS (2019)
A forging method for reducing process steps in the forming of automotive fasteners
Senyong Chen et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Preform optimization for hot forging processes using genetic algorithms
Johannes Knust et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Wear Improvement of Tools in the Cold Forging Process for Long Hex Flange Nuts
Shao-Yi Hsia et al.
MATERIALS (2015)
The effect of Microstructure and texture evolution on mechanical properties of low carbon steel in a non-circular drawing sequence
Sun Kwang Hwang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
The effect of grain refinement by multi-pass continuous hybrid process on mechanical properties of low-carbon steel wires
Sun Kwang Hwang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Multi-stage cold forging and experimental investigation for the outer race of constant velocity joints
Tae-Wan Ku et al.
MATERIALS & DESIGN (2013)
Process design of high-strength bolt of fully pearlitic high-carbon steel
Hyun-Chul Lee et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
A study on chevron crack formation and evolution in a cold extrusion
Jun-Seok Choi et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2010)
The effect of shrink fitting ratios on tool life in bolt forming processes
H. C. Lee et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Microstructural evolution in pure aluminum processed by high-pressure torsion
Yuki Ito et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Improvement of the bending fatigue resistance of the hyper-eutectoid steel wires used for tire cords by a post-processing annealing
Y. S. Yang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
The effect of cold work and heat treatment on the fatigue behaviour of 3CR12 corrosion resistant steel wire
M. Topic et al.
INTERNATIONAL JOURNAL OF FATIGUE (2007)
A finite element analysis of cold-forging dies using two- and three-dimensional models
C McCormack et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
The prediction of central burst defects in extrusion and wire drawing
DC Ko et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)