相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Improvement of mechanical properties of a cryorolled Al-Mg-Si alloy through warm rolling and aging
L. Mei et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Development of combined groove pressing and rolling to produce ultra-fine grained Al alloys and comparison with cryorolling
Kandarp Changela et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Microstructure and mechanical properties of Al-3Mg-0.25 Sc alloy sheets produced by cryorolling
S. Vigneshwaran et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Mechanical behavior and void coalescence analysis of cryorolled AA8090 alloy
K. S. V. B. R. Krishna et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Effect of cryorolling on microstructure and mechanical properties of a peak-aged AA6082 extrusion
Zebing Xu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Influence of cryorolling and followed by annealing on high cycle fatigue behavior of ultrafine grained Al 2014 alloy
Amit Joshi et al.
MATERIALS CHARACTERIZATION (2017)
Annealing effects on microstructure and mechanical properties of cryorolled Fe-25Cr-20Ni steel
Yi Xiong et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Tailoring structural inhomogeneities in metallic glasses to enable tensile ductility at room temperature
E. Ma et al.
MATERIALS TODAY (2016)
Effect of cryorolling on the microstructure and tensile properties of bulk nano-austenitic stainless steel
Barna Roy et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
A new insight into ductile fracture of ultrafine-grained Al-Mg alloys
Hailiang Yu et al.
SCIENTIFIC REPORTS (2015)
Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy
Kaka Ma et al.
ACTA MATERIALIA (2014)
Precipitation kinetics in a severely plastically deformed 7075 aluminium alloy
A. Deschamps et al.
ACTA MATERIALIA (2014)
Recovery and recrystallization in commercial purity aluminum cold rolled to an ultrahigh strain
O. V. Mishin et al.
ACTA MATERIALIA (2013)
Precipitation phenomena in an ultrafine-grained Al alloy
T. Hu et al.
ACTA MATERIALIA (2013)
Extreme grain refinement by severe plastic deformation: A wealth of challenging science
Y. Estrin et al.
ACTA MATERIALIA (2013)
Advances in ultrafine-grained materials
Yi Huang et al.
MATERIALS TODAY (2013)
The role of shear banding on the fatigue ductility of ultrafine-grained aluminium
Shokoufeh Malekjani et al.
SCRIPTA MATERIALIA (2013)
Asymmetric cryorolling for fabrication of nanostructural aluminum sheets
Hailiang Yu et al.
SCIENTIFIC REPORTS (2012)
Microstructure and texture evolution in cryorolled Al 7075 alloy
R. Jayaganthan et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2010)
Effect of cold work and non-isothermal annealing on the recrystallization behavior and texture evolution of a precipitation-hardenable aluminum alloy
B. Poorganji et al.
SCRIPTA MATERIALIA (2010)
Simultaneously enhanced strength and ductility of titanium via multimodal grain structure
D. K. Yang et al.
SCRIPTA MATERIALIA (2010)
Improving the mechanical properties of 2024 Al alloy by cryo rolling
Devaiah Doppalapudi et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2010)
The effect of strain rate on the deformation mechanisms and the strain rate sensitivity of an ultra-fine-grained Al alloy
I. Sabirov et al.
SCRIPTA MATERIALIA (2009)
Tensile deformation of an ultrafine-grained aluminium alloy: Micro shear banding and grain boundary sliding
I. Sabirov et al.
ACTA MATERIALIA (2008)
Microstructure and mechanical properties of ultra fine grained Cu-Zn and Cu-Al alloys produced by cryorolling and annealing
V. Subramanya Sarma et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
A study on the mechanical properties of cryorolled Al-Mg-Si alloy
Sushanta Kumar Panigrahi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Development of ultrafine grained high strength Al-Cu alloy by cryorolling
T Shanmugasundaram et al.
SCRIPTA MATERIALIA (2006)
Three strategies to achieve uniform tensile deformation in a nanostructured metal
YM Wang et al.
ACTA MATERIALIA (2004)
Recrystallization kinetics of individual bulk grains in 90% cold-rolled aluminium
EM Lauridsen et al.
ACTA MATERIALIA (2003)