相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Effect of process parameters on micro-textured surface generation in feed direction vibration assisted milling
X. H. Shen et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)
Influence of the grain size of CVD diamond on the thermal conductivity, material removal depth and surface roughness in nanosecond laser machining
Zhenjun Li et al.
CERAMICS INTERNATIONAL (2020)
The effect of vibration and cutting zone temperature on surface roughness and tool wear in eco-friendly MQL turning of AISI D2
Onur Ozbek et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Investigation on surface quality and burr generation of high aspect ratio (HAR) micro-milled grooves
Jinjin Han et al.
Journal of Manufacturing Processes (2020)
Structural design and fabrication of polycrystalline diamond micro ball-end mill
Hao Yuan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Experimental study on fabricating ball micro end mill with spiral blades by low speed wire electrical discharge machining
Siqian Gong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Energy consumption considering tool wear and optimization of cutting parameters in micro milling process
Xuewei Zhang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)
Design, optimization and manufacturing of polycrystalline diamond micro- end-mill for micro-milling of GH4169
Ni Chen et al.
DIAMOND AND RELATED MATERIALS (2020)
Review of ultrasonic vibration-assisted machining in advanced materials
Zhichao Yang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2020)
Recent progress of chatter prediction, detection and suppression in milling
Lida Zhu et al.
MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2020)
Investigations on burr formation mechanisms in micro milling of high-aspect-ratio titanium alloy ti-6al-4 v structures
Yang Wu et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)
The effect of cutting parameters on micro-hardness and the prediction of Vickers hardness based on a response surface methodology for micro-milling Inconel 718
Xiaohong Lu et al.
MEASUREMENT (2019)
Microstructure Evolution Modeling and Simulation for Dynamic Recrystallization of Cr12MoV Die Steel During Hot Compression Based on Real Metallographic Image
F. Sun et al.
METALS AND MATERIALS INTERNATIONAL (2019)
Research on the ploughing force in micro milling of soft-brittle crystals
Ni Chen et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)
A study on performance characteristics and multi response optimization of process parameters to maximize performance of micro milling for Ti-6Al-4V
K. Venkata Rao
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Fabrication of large aspect ratio (LAR) PCD micro-end mill with a hybrid method and performance verification
Jinjin Han et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Size-dependent responses of micro-end mill based on strain gradient elasticity theory
Yicong Du et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Machined channel quality and tool life using cermet micro-mill in micro-milling aluminum alloy
ShaSha Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment
Shuai Ren et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)
Optimization of process parameters for micro milling of Ti-6Al-4V alloy using Taguchi-based gray relational analysis
K. Aslantas et al.
MEASUREMENT (2018)
An innovative investigation on chip formation mechanisms in micro-milling using natural diamond and tungsten carbide tools
Zhichao Niu et al.
JOURNAL OF MANUFACTURING PROCESSES (2018)
Novel method for burrs quantitative evaluation in micro-milling
Fabrizio Medeossi et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2018)
Friction properties of groove texture on Cr12MoV surface
Wang Jing et al.
JOURNAL OF CENTRAL SOUTH UNIVERSITY (2017)
Surface quality in micro milling: Influences of spindle and cutting parameters
Jan C. Aurich et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2017)
3D FEM Simulation of Milling Force in Corner Machining Process
Caixu Yue et al.
CHINESE JOURNAL OF MECHANICAL ENGINEERING (2017)
Prediction of cutting temperature in orthogonal machining of AISI 316L using artificial neural network
Fuat Kara et al.
APPLIED SOFT COMPUTING (2016)
ANN and multiple regression method-based modelling of cutting forces in orthogonal machining of AISI 316L stainless steel
F. Kara et al.
NEURAL COMPUTING & APPLICATIONS (2015)
Research on the modeling of burr formation process in micro-ball end milling operation on Ti-6Al-4V
M. J. Chen et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Characterization and modeling of burr formation in micro-end milling
Ravi Lekkala et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2011)
Hardness and toughness investigations of deep cryogenic treated cold work die steel
Shaohong Li et al.
CRYOGENICS (2010)
Design of a five-axis ultra-precision micro-milling machine-UltraMill. Part 1: holistic design approach, design considerations and specifications
Dehong Huo et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Some recent advances in multi-material micro- and nano-manufacturing
E. B. Brousseau et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
An experimental analysis of process parameters to manufacture metallic micro-channels by micro-milling
Elisa Vazquez et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness
Xinmin Lai et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Micro-machining of metals, ceramics and polymers using nanosecond lasers
M. R. H. Knowles et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
The manufacturing of micro molds by conventional and energy-assisted processes
J. Fleischer et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
分享论文
