相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Effect of inclusions on low cycle fatigue lifetime in a powder metallurgy nickel-based superalloy FGH96
Dianyin Hu et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Isothermal and thermomechanical fatigue crack propagation in both virgin and thermally aged Haynes 230
D. Ewest et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Laser welding of a selective laser melted Ni-base superalloy: Microstructure and high temperature mechanical property
XiaoAn Hu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Experimental evaluation on elevated temperature fatigue and tensile properties of one selective laser melted nickel based superalloy
Z. H. Jiao et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
CNT-reinforced AlSi10Mg composite by selective laser melting: microstructural and mechanical properties
Xihe Liu et al.
MATERIALS SCIENCE AND TECHNOLOGY (2019)
Parametric Study of Cyclic Plasticity Behavior in a Directionally Solidified Superalloy with Partial Recrystallization by Crystal Plasticity Finite Element Simulation
Xianfeng Ma et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)
Effect of Local Recrystallized Grains on the Low Cycle Fatigue Behavior of a Nickel-Based Single Crystal Superalloy
Xianfeng Ma et al.
CRYSTALS (2019)
Inhomogeneous strain and recrystallisation of a shot-peened Inconel 625 alloy after annealing
Masayoshi Kumagai et al.
MATERIALS SCIENCE AND TECHNOLOGY (2019)
Notch fatigue and crack growth resistance of Ti-6Al-4V ELI additively manufactured via selective laser melting: A critical distance approach to defect sensitivity
M. Benedetti et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Effect of structural support on microstructure of nickel base superalloy fabricated by laser-powder bed fusion additive manufacturing
Hyeyun Song et al.
ADDITIVE MANUFACTURING (2019)
Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion
Fan Zhang et al.
ACTA MATERIALIA (2018)
Heat treatment effect on the microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting for proton exchange membrane fuel cells
Decheng Kong et al.
ELECTROCHIMICA ACTA (2018)
Long fatigue crack propagation behavior of Inconel 625 processed by laser powder bed fusion: Influence of build orientation and post-processing conditions
J. -R. Poulin et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Influence of SLM process parameters on the surface finish, porosity rate and fatigue behavior of as-built Inconel 625 parts
Imade Koutiri et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Influence of heat treatments on microstructure evolution and mechanical properties of Inconel 625 processed by laser powder bed fusion
Giulio Marchese et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
Microstructural degradation of polycrystalline superalloys from oxidized carbides and implications on crack initiation
Paraskevas Kontis et al.
SCRIPTA MATERIALIA (2018)
Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel
Aref Yadollahi et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Thermo-mechanical low-cycle fatigue-creep of Haynes 230
Raasheduddin Ahmed et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2017)
Interfacial phenomena and characteristics between the deposited material and substrate in selective laser melting Inconel 625
C. Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Elevated temperature mechanical behavior of IN625 alloy processed by laser powder-bed fusion
Alena Kreitcberg et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Effect of heat treatment and hot isostatic pressing on the microstructure and mechanical properties of Inconel 625 alloy processed by laser powder bed fusion
Alena Kreitcberg et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Microstructure evolution characteristics of Inconel 625 alloy from selective laser melting to heat treatment
C. Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Microstructure and yield strength of SLM-fabricated CM247LC Ni-Superalloy
Xiqian Wang et al.
ACTA MATERIALIA (2017)
Unified viscoplasticity modeling for isothermal low-cycle fatigue and fatigue-creep stress-strain responses of Haynes 230
Raasheduddin Ahmed et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2016)
Isothermal low-cycle fatigue and fatigue-creep of Haynes 230
Paul R. Barrett et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2016)
Microstructure Characteristics of Inconel 625 Superalloy Manufactured by Selective Laser Melting
Shuai Li et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2015)
Influence of grain orientation on the incipient oxidation behavior of Haynes 230 at 900 °C
Xu Wang et al.
MATERIALS CHARACTERIZATION (2015)
Selective laser melting additive manufacturing of TiC/Inconel 718 bulk-form nanocomposites: Densification, microstructure, and performance
Qingbo Jia et al.
JOURNAL OF MATERIALS RESEARCH (2014)
Injection molding of nickel based 625 superalloy: Sintering, heat treatment, microstructure and mechanical properties
Ozgur Ozgun et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2013)
Laser additive manufacturing of metallic components: materials, processes and mechanisms
D. D. Gu et al.
INTERNATIONAL MATERIALS REVIEWS (2012)
The effect of M23C6 carbides on the formation of grain boundary serrations in a wrought Ni-based superalloy
Li Jiang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
The microstructure evolution and nucleation mechanisms of dynamic recrystallization in hot-deformed Inconel 625 superalloy
Defu Li et al.
MATERIALS & DESIGN (2011)
Anomalous deformation behavior and twin formation of Ni-base superalloys at the intermediate temperatures
I. S. Kim et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Effects of high temperature aging in an impure helium environment on low temperature embrittlement of Alloy 617 and Haynes 230
Daejong Kim et al.
JOURNAL OF NUCLEAR MATERIALS (2010)
分享论文
