相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Evolution of the microstructure and mechanical properties of stereolithography formed alumina cores sintered in vacuum
He Li et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)
Influence of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3 Ceramic via 3D Stereolithography
He Li et al.
ACTA METALLURGICA SINICA-ENGLISH LETTERS (2020)
Development of biodegradable bioactive glass ceramics by DLP printed containing EPCs/BMSCs for bone tissue engineering of rabbit mandible defects
Fangfang Xu et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2020)
Influence of test procedure on dielectric breakdown strength of alumina
Bjoern Mieller
JOURNAL OF ADVANCED CERAMICS (2019)
Mechanical properties and microstructures of 3D printed bulk cordierite parts
Zhangwei Chen et al.
CERAMICS INTERNATIONAL (2019)
Effect of calcination temperature on structural and optical properties of MAl2O4 (M = Ni, Cu, Zn) aluminate spinel nanoparticles
Thanit Tangcharoen et al.
JOURNAL OF ADVANCED CERAMICS (2019)
Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration
Zanlin Cheng et al.
JOURNAL OF ADVANCED CERAMICS (2019)
Thermal Treatment of γ-Al2O3 for the Preparation of Stereolithography 3D Printing Ceramic Slurries
He Li et al.
FRONTIERS IN MATERIALS (2019)
3D printing of ceramics: A review
Zhangwei Chen et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)
Fabrication of complex-shaped zirconia ceramic parts via a DLP-stereolithography-based 3D printing method
Rongxuan He et al.
CERAMICS INTERNATIONAL (2018)
Effects of oxygen contents on sintering mechanism and sintering-neck growth behaviour of Fe-Cr powder
Hao He et al.
POWDER TECHNOLOGY (2018)
Optimal design on the high-temperature mechanical properties of porous alumina ceramics based on fractal dimension analysis
Jingjing Liu et al.
JOURNAL OF ADVANCED CERAMICS (2018)
Gelcasting of zirconia-based all-ceramic teeth combined with stereolithography
Kai Liu et al.
CERAMICS INTERNATIONAL (2018)
A review of the additive manufacturing (3DP) of bioceramics: alumina, zirconia (PSZ) and hydroxyapatite
L. Ferrage et al.
JOURNAL OF THE AUSTRALIAN CERAMIC SOCIETY (2017)
Amino-functionalization of colloidal alumina particles for enhancement of the infiltration behavior in a silica-based ceramic core
Gye Seok An et al.
CERAMICS INTERNATIONAL (2017)
High-surface-area ceria prepared by ALD on Al2O3 support
Tzia Ming Onn et al.
APPLIED CATALYSIS B-ENVIRONMENTAL (2017)
Effect of in situ synthesised mullite whiskers on the high-temperature strength of Al2O3-based ceramic moulds for casting hollow turbine blades
Zhongliang Lu et al.
CERAMICS INTERNATIONAL (2016)
Characterization of ceramic components fabricated using binder jetting additive manufacturing technology
J. A. Gonzalez et al.
CERAMICS INTERNATIONAL (2016)
FAST/SPS sintering of nanocrystalline zinc oxide-Part II: Abnormal grain growth, texture and grain anisotropy
Benjamin Dargatz et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)
Ceramic cores for turbine blades via injection moulding
Magdalena Gromada et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
A phase-inversion casting process for preparation of tubular porous alumina ceramic membranes
Zhiwen Zhu et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)
Separating macrostresses from microstresses in Al2O3-15 vol%SiC particulate reinforced composites
Ji Zou et al.
SCRIPTA MATERIALIA (2015)
Additive Manufacturing of Dense Alumina Ceramics
Martin Schwentenwein et al.
INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2015)
Effect of particle size distribution of raw powders on pore size distribution and bending strength of Al2O3 microfiltration membrane supports
Qibing Chang et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)
Investigation on cristobalite crystallization in silica-based ceramic cores for investment casting
A. Kazemi et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)
Preparation and characterization of porous alumina ceramics through starch consolidation casting technique
R. M. Khattab et al.
CERAMICS INTERNATIONAL (2012)
Ceramic Preforms with 2D Regular Channels for Fabrication of Metal/Ceramic-Reinforced Composites
Osayande L. Ighodaro et al.
INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2012)
Nanoindentation, AFM and tribological properties of thin nc-WC/a-C Coatings
Frantisek Lofaj et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)
Gelcasting of alumina based ceramic cores containing yttria for single crystal and directional solidification blades
H. H. Wu et al.
ADVANCES IN APPLIED CERAMICS (2009)
Two-step sintering of fine alumina-zirconia ceramics
Chih-Jen Wang et al.
CERAMICS INTERNATIONAL (2009)
Reaction-sintered porous mineral-based mullite ceramic membrane supports made from recycled materials
Yingchao Dong et al.
JOURNAL OF HAZARDOUS MATERIALS (2009)
Dissolved Argon Changes the Rate of Diffusion in Room Temperature Ionic Liquids: Effect of the Presence and Absence of Argon and Nitrogen on the Voltammetry of Ferrocene
Laura E. Barrosse-Antle et al.
JOURNAL OF PHYSICAL CHEMISTRY C (2009)
Green ceramic machining: A top-down approach for the rapid fabrication of complex-shaped ceramics
B. Su et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2008)
α-Cr2O3 template-texture effect on α-Al2O3 thin-film growth
P. Eklund et al.
THIN SOLID FILMS (2008)
Fabrication of mullite ceramics with ultrahigh porosity by gel freeze drying
Shuqiang Ding et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2007)
Influence of sintering temperature and pressure on crystallite size and lattice defect structure in nanocrystalline SiC
J. Gubicza et al.
JOURNAL OF MATERIALS RESEARCH (2007)
Alumina nanopowder production from synthetic Bayer liquor
Mahyar Mazloumi et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2006)
Fracture toughness (KIC), hardness, sintering and grain growth behaviour of 8YSCZ/Al2O3 composites produced by colloidal processing
S Tekeli
JOURNAL OF ALLOYS AND COMPOUNDS (2005)
Reinforcement of alumina matrix with multi-walled carbon nanotubes
J Sun et al.
CERAMICS INTERNATIONAL (2005)
Microfabrication of ceramic components by microstereolithography
A Bertsch et al.
JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2004)
Effect of core materials on the formation of hollow alumina microspheres by mechanofusion process
T Kato et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2004)
Effect of sintering temperature on microstructure of hydrothermally prepared bismuth sodium titanate ceramics
P Pookmanee et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2004)
Raman spectra of synthetic sapphire
M Kadleíková et al.
MICROELECTRONICS JOURNAL (2001)
Calcination and sintering of fluorapatite under argon atmosphere
F Ben Ayed et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2001)
Gas pressure sintering of beta SiC-gamma-AlON composite in nitrogen/argon environment
S Mandal et al.
CERAMICS INTERNATIONAL (2001)
Effects of electric current on solid state phase transformations in metals
H Conrad
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)