相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。From Topology Optimization Design to Additive Manufacturing: Today's Success and Tomorrow's Roadmap
Liang Meng et al.
ARCHIVES OF COMPUTATIONAL METHODS IN ENGINEERING (2020)
Inherent strain homogenization for fast residual deformation simulation of thin-walled lattice support structures built by laser powder bed fusion additive manufacturing
Xuan Liang et al.
ADDITIVE MANUFACTURING (2020)
Novel approach to optimized support structures in laser beam melting by combining process simulation with topology optimization
Katharina Bartsch et al.
JOURNAL OF LASER APPLICATIONS (2019)
Design against distortion for additive manufacturing
Anas Yaghi et al.
ADDITIVE MANUFACTURING (2019)
Beautiful and Functional: A Review of Biomimetic Design in Additive Manufacturing
Anton du Plessis et al.
ADDITIVE MANUFACTURING (2019)
On utilizing topology optimization to design support structure to prevent residual stress induced build failure in laser powder bed metal additive manufacturing
Lin Cheng et al.
ADDITIVE MANUFACTURING (2019)
Topology optimization of thermal conductive support structures for laser additive manufacturing
Mingdong Zhou et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2019)
Part-scale build orientation optimization for minimizing residual stress and support volume for metal additive manufacturing: Theory and experimental validation
Lin Cheng et al.
COMPUTER-AIDED DESIGN (2019)
Fully parallel level set method for large-scale structural topology optimization
Hui Liu et al.
COMPUTERS & STRUCTURES (2019)
An inherent strain based multiscale modeling framework for simulating part-scale residual deformation for direct metal laser sintering
Qian Chen et al.
ADDITIVE MANUFACTURING (2019)
Validation of Mechanical Layer Equivalent Method for simulation of residual stresses in additive manufactured components
Marvin Siewert et al.
COMPUTERS & MATHEMATICS WITH APPLICATIONS (2019)
3-Dimensional heat transfer modeling for laser powder-bed fusion additive manufacturing with volumetric heat sources based on varied thermal conductivity and absorptivity
Zhidong Zhang et al.
OPTICS AND LASER TECHNOLOGY (2019)
Bi-directional Evolutionary Structural Optimization on Advanced Structures and Materials: A Comprehensive Review
Liang Xia et al.
ARCHIVES OF COMPUTATIONAL METHODS IN ENGINEERING (2018)
Support structure design in additive manufacturing based on topology optimization
Yu-Hsin Kuo et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2018)
Environmentally enhanced creep crack growth by grain boundary cavitation under cyclic loading
Jian-Feng Wen et al.
ACTA MATERIALIA (2018)
Taking into account thermal residual stresses in topology optimization of structures built by additive manufacturing
Gregoire Allaire et al.
MATHEMATICAL MODELS & METHODS IN APPLIED SCIENCES (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
Current and future trends in topology optimization for additive manufacturing
Jikai Liu et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2018)
Combined optimization of part topology, support structure layout and build orientation for additive manufacturing
Matthijs Langelaar
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2018)
On the measurement of relative powder-bed compaction density in powder-bed additive manufacturing processes
Usman Ali et al.
MATERIALS & DESIGN (2018)
A critical review of powder-based additive manufacturing of ferrous alloys: Process parameters, microstructure and mechanical properties
Haniyeh Fayazfar et al.
MATERIALS & DESIGN (2018)
Support Structures for Additive Manufacturing: A Review
Jingchao Jiang et al.
JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING (2018)
A modified method for estimating inherent strains from detailed process simulation for fast residual distortion prediction of single-walled structures fabricated by directed energy deposition
Xuan Liang et al.
ADDITIVE MANUFACTURING (2018)
Prediction of microstructure, residual stress, and deformation in laser powder bed fusion process
Y. P. Yang et al.
COMPUTATIONAL MECHANICS (2018)
Topology optimization of self-supporting support structures for additive manufacturing
Francesco Mezzadri et al.
ADDITIVE MANUFACTURING (2018)
Improvement of the bridge curvature method to assess residual stresses in selective laser melting
Sabine Le Roux et al.
ADDITIVE MANUFACTURING (2018)
An additive manufacturing filter for topology optimization of print-ready designs
Matthijs Langelaar
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2017)
Undercut and overhang angle control in topology optimization: A density gradient based integral approach
Xiaoping Qian
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2017)
Giga-voxel computational morphogenesis for structural design
Niels Aage et al.
NATURE (2017)
Maximum length scale in density based topology optimization
Boyan S. Lazarov et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2017)
Efficient predictive model of part distortion and residual stress in selective laser melting
C. Li et al.
ADDITIVE MANUFACTURING (2017)
Multi-physics modeling of single/multiple-track defect mechanisms in electron beam selective melting
Wentao Yan et al.
ACTA MATERIALIA (2017)
An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V
Tatiana Mishurova et al.
MATERIALS (2017)
Topology Optimization in Aircraft and Aerospace Structures Design
Ji-Hong Zhu et al.
ARCHIVES OF COMPUTATIONAL METHODS IN ENGINEERING (2016)
Bridging topology optimization and additive manufacturing
Tomas Zegard et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2016)
A System for High-Resolution Topology Optimization
Jun Wu et al.
IEEE TRANSACTIONS ON VISUALIZATION AND COMPUTER GRAPHICS (2016)
A multiscale modeling approach for fast prediction of part distortion in selective laser melting
C. Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design
Andrew T. Gaynor et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2016)
Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation
L. Parry et al.
ADDITIVE MANUFACTURING (2016)
Minimum length scale in topology optimization by geometric constraints
Mingdong Zhou et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2015)
Topology optimization using PETSc: An easy-to-use, fully parallel, open source topology optimization framework
Niels Aage et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2015)
Reduction in mechanical anisotropy through high temperature heat treatment of Hastelloy X processed by Selective Laser Melting (SLM)
T. Etter et al.
17TH INTERNATIONAL CONFERENCE ON TEXTURES OF MATERIALS (ICOTOM 17) (2015)
Evaluations of effective thermal conductivity of support structures in selective laser melting
Kai Zeng et al.
ADDITIVE MANUFACTURING (2015)
Investigation on reducing distortion by preheating during manufacture of aluminum components using selective laser melting
Damien Buchbinder et al.
JOURNAL OF LASER APPLICATIONS (2014)
Mesoscopic simulation model of selective laser melting of stainless steel powder
Saad A. Khairallah et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting
F. Calignano
MATERIALS & DESIGN (2014)
Advanced lattice support structures for metal additive manufacturing
Ahmed Hussein et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Topology optimization approaches A comparative review
Ole Sigmund et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2013)
Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method
Jean-Pierre Kruth et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2012)
Investigations on residual stresses and deformations in selective laser melting
Michael F. Zaeh et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2010)
A critical review of established methods of structural topology optimization
G. I. N. Rozvany
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2009)
Residual stresses in selective laser sintering and selective laser melting
Peter Mercelis et al.
RAPID PROTOTYPING JOURNAL (2006)
Structural optimization using sensitivity analysis and a level-set method
G Allaire et al.
JOURNAL OF COMPUTATIONAL PHYSICS (2004)
A 99 line topology optimization code written in Matlab
O Sigmund
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2001)