相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Hot cracking mechanism affecting a non-weldable Ni-based superalloy produced by selective electron Beam Melting
Edouard Chauvet et al.
ACTA MATERIALIA (2018)
A modeling study of stress and strain formation induced during melting process in powder-bed electron beam melting for Ni superalloy
Satoshi Tadano et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Additive Manufacturing of Nickel Superalloys: Opportunities for Innovation and Challenges Related to Qualification
S. S. Babu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)
Microstructure and Mechanical Properties of CMSX-4 Single Crystals Prepared by Additive Manufacturing
C. Koerner et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)
A peak position comparison method for high-speed quantitative Laue microdiffraction data processing
Jiawei Kou et al.
SCRIPTA MATERIALIA (2018)
Mechanism of heat affected zone cracking in Ni-based superalloy DZ125L fabricated by laser 3D printing technique
Yao Li et al.
MATERIALS & DESIGN (2018)
Peritectic titanium alloys for 3D printing
Pere Barriobero-Vila et al.
NATURE COMMUNICATIONS (2018)
Epitaxial deposition of nickel-based superalloy Rene 142 through scanning laser epitaxy (SLE)
Amrita Basak et al.
ADDITIVE MANUFACTURING (2018)
Experimental optimization of laser additive manufacturing process of single-crystal nickel-base superalloys by a statistical experiment design method
Yao-Jian Liang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Additive manufacturing of metals: a brief review of the characteristic microstructures and properties of steels, Ti-6Al-4V and high-entropy alloys
Stephane Gorsse et al.
SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2017)
An experimental investigation into the stress and strain development of a Ni-base single crystal superalloy during cooling from solidification
Chunlei Qiu et al.
MATERIALS & DESIGN (2017)
Microstructural control during laser additive manufacturing of single-crystal nickel-base superalloys: New processing-microstructure maps involving powder feeding
Yao-Jian Liang et al.
MATERIALS & DESIGN (2017)
Massive nanoprecipitation in an Fe-19Ni-xAl maraging steel triggered by the intrinsic heat treatment during laser metal deposition
Philipp Kuernsteiner et al.
ACTA MATERIALIA (2017)
Microstructure of the Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting
Markus Ramsperger et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
Additive Manufacturing of Single-Crystal Superalloy CMSX-4 Through Scanning Laser Epitaxy: Computational Modeling, Experimental Process Development, and Process Parameter Optimization
Amrita Basak et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
Alloy design for aircraft engines
Tresa M. Pollock
NATURE MATERIALS (2016)
Solution Heat Treatment of the Single Crystal Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting
Markus Ramsperger et al.
ADVANCED ENGINEERING MATERIALS (2015)
Microstructure simulation on recrystallization of an as-cast nickel based single crystal superalloy
Li Zhonglin et al.
COMPUTATIONAL MATERIALS SCIENCE (2015)
Numerical modeling of microstructure evolution during laser additive manufacturing of a nickel-based superalloy
Pulin Nie et al.
ACTA MATERIALIA (2014)
Effects of stacking fault energy on the creep behaviors of Ni-base superalloy
Chenggang Tian et al.
MATERIALS & DESIGN (2014)
Creep behavior under isothermal and non-isothermal conditions of AM3 single crystal superalloy for different solutioning cooling rates
S. Steuer et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Measurement of the effective γ/γ′ lattice mismatch during high temperature creep of Ni-based single crystal superalloy
Laura Dirand et al.
MATERIALS CHARACTERIZATION (2013)
Temperature-dependent ideal strength and stacking fault energy of fcc Ni: a first-principles study of shear deformation
S. L. Shang et al.
JOURNAL OF PHYSICS-CONDENSED MATTER (2012)
Microstructural and mechanical approaches of the selective laser melting process applied to a nickel-base superalloy
T. Vilaro et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Effect of cyclic recovery heat treatment on surface recrystallization of a directionally solidified superalloy
Guang Xie et al.
PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2011)
The effect of alloying elements on the dislocation climbing velocity in Ni: A first-principles study
Xiao-Xiang Yu et al.
ACTA MATERIALIA (2009)
A dedicated superbend x-ray microdiffraction beamline for materials, geo-, and environmental sciences at the advanced light source
Martin Kunz et al.
REVIEW OF SCIENTIFIC INSTRUMENTS (2009)
Dislocation structures and their relationship to strength in deformed nickel microcrystals
D. M. Norfleet et al.
ACTA MATERIALIA (2008)
Plastic strain-induced rafting of γ′ precipitates in Ni superalloys:: Elasticity analysis
N. Ratel et al.
ACTA MATERIALIA (2006)
The effect of lattice misfit on the dislocation motion in superalloys during high-temperature low-stress creep
JX Zhang et al.
ACTA MATERIALIA (2005)
About the relations between finite strain in non-cubic crystals and the related phenomenological P-V Equation of State
A Pavese
PHYSICS AND CHEMISTRY OF MINERALS (2005)
The effect of welding conditions on stray grain formation in single crystal welds - theoretical analysis
JM Vitek
ACTA MATERIALIA (2005)
Gas turbine technology evolution: A designer's perspective
BL Koff
JOURNAL OF PROPULSION AND POWER (2004)
Recrystallisation of single crystal superalloy CMSX-4
DC Cox et al.
MATERIALS SCIENCE AND TECHNOLOGY (2003)
Rafting in single crystal nickel-base superalloys - An overview
M Kamaraj
SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES (2003)
Single-crystal laser deposition of superalloys:: Processing-microstructure maps
M Gäumann et al.
ACTA MATERIALIA (2001)
分享论文
