相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends
Jinliang Zhang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
Effects of Surface Finishing Procedures on Corrosion Behavior of DMLS-AlSi10Mg_200C Alloy Versus Die-Cast A360.1 Aluminum
P. Fathi et al.
JOM (2019)
Identification and characterization of spatter particles and their effect on surface roughness, density and mechanical response of 17-4 PH stainless steel laser powder-bed fusion parts
Usman Ali et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
On the effect of spatter particles distribution on the quality of Hastelloy X parts made by laser powder-bed fusion additive manufacturing
Reza Esmaeilizadeh et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Fluid and particle dynamics in laser powder bed fusion
P. Bidare et al.
ACTA MATERIALIA (2018)
Fatigue properties of AlSi10Mg obtained by additive manufacturing: Defect-based modelling and prediction of fatigue strength
S. Romano et al.
ENGINEERING FRACTURE MECHANICS (2018)
Effect of heat treatments on fatigue property of selective laser melting AlSi10Mg
Changchun Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Influence of SLM process parameters on the surface finish, porosity rate and fatigue behavior of as-built Inconel 625 parts
Imade Koutiri et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Porosity formation mechanisms and fatigue response in Al-Si-Mg alloys made by selective laser melting
Kun V. Yang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
On the fatigue strength enhancement of additive manufactured AlSi10Mg parts by mechanical and thermal post-processing
Sara Bagherifard et al.
MATERIALS & DESIGN (2018)
Defect analysis and fatigue design basis for Ni-based superalloy 718 manufactured by selective laser melting
Yoichi Yamashita et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Fatigue properties and material characteristics of additively manufactured AlSiW10Mg-Effect of the contour parameter on the microstructure, density, residual stress, roughness and mechanical properties
Emilie Beevers et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Effects of Platform Pre-Heating and Thermal-Treatment Strategies on Properties of AlSi10Mg Alloy Processed by Selective Laser Melting
Riccardo Casati et al.
METALS (2018)
A study on the effect of energy input on spatter particles creation during selective laser melting process
Mohsen Taheri Andani et al.
ADDITIVE MANUFACTURING (2018)
Internal surface measurement of metal powder bed fusion parts
Adam Thompson et al.
ADDITIVE MANUFACTURING (2018)
On morphological surface features of the parts printed by selective laser melting (SLM)
Milad Hamidi Nasab et al.
ADDITIVE MANUFACTURING (2018)
Spatter and oxide formation in laser powder bed fusion of Inconel 718
A. N. D. Gasper et al.
ADDITIVE MANUFACTURING (2018)
On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM)
Naor Elad Uzan et al.
ADDITIVE MANUFACTURING (2018)
Application of mechanical surface finishing processes for roughness reduction and fatigue improvement of additively manufactured Ti-6Al-4V parts
S. Bagehorn et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting
Ming Tang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Additive manufacturing of fatigue resistant materials: Challenges and opportunities
Aref Yadollahi et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
A comparison of fatigue strength sensitivity to defects for materials manufactured by AM or traditional processes
S. Beretta et al.
INTERNATIONAL JOURNAL OF FATIGUE (2017)
Fatigue of AlSi10Mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM)
Naor Elad Uzan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones
Saad A. Khairallah et al.
ACTA MATERIALIA (2016)
The metallurgy and processing science of metal additive manufacturing
W. J. Sames et al.
INTERNATIONAL MATERIALS REVIEWS (2016)
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Todd M. Mower et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Surface texture metrology for metal additive manufacturing: a review
A. Townsend et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2016)
A Review on Fatigue Life Prediction Methods for Metals
E. Santecchia et al.
ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2016)
Improving the fatigue behaviour of a selectively laser melted aluminium alloy: Influence of heat treatment and surface quality
Nesma T. Aboulkhair et al.
MATERIALS & DESIGN (2016)
Improving the surface quality and mechanical properties by shot-peening of 17-4 stainless steel fabricated by additive manufacturing
Bandar AlMangour et al.
MATERIALS & DESIGN (2016)
A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V
Marco Simonelli et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
Surface topography and the impact on fatigue performance
D. T. Ardi et al.
SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2015)
The effect of roughness and residual stresses on fatigue life time of an alloy of titanium
K. Moussaoui et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
On the fatigue properties of metals manufactured by selective laser melting - The role of ductility
Stefan Leuders et al.
JOURNAL OF MATERIALS RESEARCH (2014)
Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder
Lore Thijs et al.
ACTA MATERIALIA (2013)
Fatigue performance of additive manufactured metallic parts
A. B. Spierings et al.
RAPID PROTOTYPING JOURNAL (2013)
Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior
Erhard Brandl et al.
MATERIALS & DESIGN (2012)
Extreme value models for the assessment of steels containing multiple types of inclusion
S Beretta et al.
ACTA MATERIALIA (2006)
分享论文
