相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Quantification of the strengthening effect of reinforcements during hot deformation of aluminum-based composites
Hamed Mirzadeh
MATERIALS & DESIGN (2015)
Constitutive modeling and prediction of hot deformation flow stress under dynamic recrystallization conditions
Hamed Mirzadeh
MECHANICS OF MATERIALS (2015)
Constitutive analysis of Mg-Al-Zn magnesium alloys during hot deformation
Hamed Mirzadeh
MECHANICS OF MATERIALS (2014)
A comparative study on Johnson-Cook, modified Johnson-Cook and Arrhenius-type constitutive models to predict the high temperature flow stress in 20CrMo alloy steel
An He et al.
MATERIALS & DESIGN (2013)
Constitutive models to predict flow stress in Austenitic Stainless Steel 316 at elevated temperatures
Amit Kumar Gupta et al.
MATERIALS & DESIGN (2013)
A comparative study on modified Johnson Cook, modified Zerilli-Armstrong and Arrhenius-type constitutive models to predict the hot deformation behavior in 28CrMnMoV steel
Hong-Ying Li et al.
MATERIALS & DESIGN (2013)
Determination of Johnson-Cook parameters from machining simulations
Aviral Shrot et al.
COMPUTATIONAL MATERIALS SCIENCE (2012)
The high temperature flow behavior modeling of AZ81 magnesium alloy considering strain effects
P. Changizian et al.
MATERIALS & DESIGN (2012)
Constitutive behavior of as-cast A356
M. J. Roy et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Constitutive relationships for hot deformation of austenite
Hamed Mirzadeh et al.
ACTA MATERIALIA (2011)
Hot deformation behavior of austenite in HSLA-100 microalloyed steel
A. Momeni et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
A new mathematical model for predicting flow stress of typical high-strength alloy steel at elevated high temperature
Y. C. Lin et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
Influence of thermomechanical processing and heat treatments on tensile and Charpy impact properties of B and Cu bearing high-strength low-alloy steels
Byoungchul Hwang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
A modified Johnson-Cook model for tensile behaviors of typical high-strength alloy steel
Y. C. Lin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Modeling of flow stress for magnesium alloy during hot deformation
Yin-Jiang Qin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
A comparative study on Johnson Cook, modified Zerilli-Armstrong and Arrhenius-type constitutive models to predict elevated temperature flow behaviour in modified 9Cr-1Mo steel
Dipti Samantaray et al.
COMPUTATIONAL MATERIALS SCIENCE (2009)
A thermo-viscoplastic constitutive model to predict elevated-temperature flow behaviour in a titanium-modified austenitic stainless steel
Dipti Samantaray et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Constitutive equations to predict high temperature flow stress in a Ti-modified austenitic stainless steel
Sumantra Mandal et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Prediction of 42CrMo steel flow stress at high temperature and strain rate
Y. C. Lin et al.
MECHANICS RESEARCH COMMUNICATIONS (2008)
Microstructure and mechanical properties of 780 MPa high strength steels produced by direct-quenching and tempering process
WS Chang
JOURNAL OF MATERIALS SCIENCE (2002)
分享论文
