相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。The effect of a prior short-term ageing on mechanical and creep properties of P92 steel
V. Sklenicka et al.
MATERIALS CHARACTERIZATION (2018)
Creep deformation and rupture behaviour of service exposed P91 weld and base steel measured by miniature tensile creep testing
Deniz Taygun Erten et al.
MATERIALS AT HIGH TEMPERATURES (2017)
Microstructure-based assessment of creep rupture behaviour of cast-forged P91 steel
Chandan Pandey et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Nano-size Particle Evolution During Heat Treatment of P91 Steel and Their Effect on Micro Hardness
C. Pandey et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)
Tempering behavior of a low nitrogen boron-added 9%Cr steel
I. Fedorova et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
A review of dynamic recrystallization phenomena in metallic materials
K. Huang et al.
MATERIALS & DESIGN (2016)
Finite Element Analysis of Plastic Deformation During Impression Creep
Naveena et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2015)
Impression creep deformation behaviour of 316LN stainless steel
Naveena et al.
MATERIALS AT HIGH TEMPERATURES (2015)
Evaluation of creep deformation behaviour of different microstuctural zones of 316LN SS weld joint using impression creep testing technique
Naveena V. D. Vijayanand et al.
MATERIALS SCIENCE AND TECHNOLOGY (2014)
Impression Creep Behavior of 316LN Stainless Steel
M. D. Mathew et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2013)
Impression test-A review
Fuqian Yang et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2013)
Creep Behaviour of 9CrMoNbV (P91) Steel Having a Small Amount of Boron
J. Baral et al.
6TH INTERNATIONAL CONFERENCE ON CREEP, FATIGUE AND CREEP-FATIGUE INTERACTION (2013)
Evaluation of the effect of nitrogen on creep properties of 316LN stainless steel from impression creep tests
Naveena et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Evolution of precipitated phases during prolonged tempering in a 9%Cr1%MoVNb ferritic-martensitic steel: Influence on creep performance
N. Zavaleta Gutierrez et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Microstructure evolution in HAZ and suppression of Type IV fracture in advanced ferritic power plant steels
F. Abe et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2010)
Study of the microstructure of the Grade 91 steel after more than 100,000 h of creep exposure at 600 °C
C. G. Panait et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2010)
Influence of precipitation on dislocation substructure and creep properties of P91 steel weld joints
Dagmar Jandova et al.
MATERIALS AT HIGH TEMPERATURES (2010)
The microstructure and impression creep behavior of cast, Mg-5Sn-xCa alloys
G. Nayyeri et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
TEM investigations of MN nitride phases in a 9% chromium ferritic/martensitic steel with normalization conditions for nuclear reactors
Yin Zhong Shen et al.
JOURNAL OF NUCLEAR MATERIALS (2009)
Precipitate phases of a ferritic/martensitic 9% Cr steel for nuclear power reactors
Yin Zhong Shen et al.
NUCLEAR ENGINEERING AND DESIGN (2009)
Ferritic/martensitic steels for advanced nuclear reactors
R. L. Klueh
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2009)
Vanadium nitride precipitate phase in a 9% chromium steel for nuclear power plant applications
Y. Z. Shen et al.
JOURNAL OF NUCLEAR MATERIALS (2008)
Microstructural analysis on a creep resistant martensitic 9-12% Cr steel using the EBSD method
B. Sonderegger et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Martensite laths in creep resistant martensitic 9-12% Cr steels - Calculation and measurement of misorientations
B. Sonderegger et al.
MATERIALS CHARACTERIZATION (2007)
Suppression of Type IV fracture and improvement of creep strength of 9Cr steel welded joints by boron addition
Fujio Abe et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2007)
Suppressing type IV failure via modification of heat affected zone microstructures using high boron content in 9Cr heat resistant steel welded joints
M Kondo et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2006)
Impression creep of a Mg-8Zn4Al-0.5Ca alloy
LL Peng et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Effect of welding process and groove angle on type IV cracking behaviour of weld joints of a ferritic steel
SK Albert et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2005)
Creep of a TiAl alloy:: a comparison of indentation and tensile testing
D Dorner et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Impression creep and other localized tests
JCM Li
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)
Creep behavior and stability of MX precipitates at high temperature in 9Cr-0.5Mo-1.8W-VNb steel
K Sawada et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)
Strengthening mechanisms of creep resistant tempered martensitic steel
K Maruyama et al.
ISIJ INTERNATIONAL (2001)
Microstructural evolution during creep test in 9Cr-2W-V-Ta steels and 9Cr-1 Mo-V-Nb steels
T Hasegawa et al.
ISIJ INTERNATIONAL (2001)