相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Fast mold surface temperature evolution: relevance of asymmetric surface heating for morphology of iPP molded samples
S. Liparoti et al.
RSC ADVANCES (2015)
Development and evaluation of a new rapid mold heating and cooling method for rapid heat cycle molding
Guilong Wang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2014)
Evolution of iPP Relaxation Spectrum during Crystallization
Roberto Pantani et al.
MACROMOLECULAR THEORY AND SIMULATIONS (2014)
Heating/cooling channels design for an automotive interior part and its evaluation in rapid heat cycle molding
Gui-long Wang et al.
MATERIALS & DESIGN (2014)
Experimental research on the effects of cavity surface temperature on surface appearance properties of the moulded part in rapid heat cycle moulding process
Guilong Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Influence of Mold Temperature on Mold Filling Behavior and Part Properties in Micro Injection Molding
S. Meister et al.
INTERNATIONAL POLYMER PROCESSING (2013)
Research on the reduction of sink mark and warpage of the molded part in rapid heat cycle molding process
Xiaoxin Wang et al.
MATERIALS & DESIGN (2013)
Determination of the effect of pressure on viscosity of an isotactic polypropylene
Andrea Sorrentino et al.
POLYMER BULLETIN (2013)
Improving the Predictions of Injection Molding Simulation Software
U. Vietri et al.
POLYMER ENGINEERING AND SCIENCE (2011)
Analysis of Shrinkage Development of a Semicrystalline Polymer during Injection Molding
Felice De Santis et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2010)
Rapid mold temperature control in injection molding by using steam heating
Ming-Chang Jeng et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2010)
Thermally and flow induced crystallization of polymers at low shear rate
M'hamed Boutaous et al.
JOURNAL OF NON-NEWTONIAN FLUID MECHANICS (2010)
Shear-Induced Nucleation and Growth in Isotactic Polypropylene
Roberto Pantani et al.
MACROMOLECULES (2010)
Analysis of thermal cycling efficiency and optimal design of heating/cooling systems for rapid heat cycle injection molding process
Wang Guilong et al.
MATERIALS & DESIGN (2010)
Research of thermal response simulation and mold structure optimization for rapid heat cycle molding processes, respectively, with steam heating and electric heating
Guilong Wang et al.
MATERIALS & DESIGN (2010)
Warpage and structural analysis of thin shell plastic in the plastic injection molding
Babur Ozcelik et al.
MATERIALS & DESIGN (2009)
Study on residual stresses of thin-walled injection molding
TH Wang et al.
EUROPEAN POLYMER JOURNAL (2005)
Temperature measurements in the depth and at the surface of injected thermoplastic parts
Y Farouq et al.
MEASUREMENT (2005)
Kinetics of polymer crystallization under processing conditions: transformation of dormant nuclei by the action of flow
H Janeschitz-Kriegel et al.
POLYMER (2005)
Flow-induced crystallization in the injection molding of polymers: A thermodynamic approach
KH Kim et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2005)
Development of the skin layer in injection moulding: phenomenological model
JC Viana
POLYMER (2004)
Crystallization kinetics and solidified structure in iPP under high cooling rates
I Coccorullo et al.
POLYMER (2003)
Investigations of the tensile properties on polycarbonate thin-wall injection molded parts
SC Chen et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2003)
Shear-enhanced crystallization in isotactic polypropylene Part 2. Analysis of the formation of the oriented skin
G Kumaraswamy et al.
POLYMER (2000)
分享论文
