相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。FE/SPH modelling of orthogonal micro-machining of f.c.c. single crystal
S. Abolfazl Zahedi et al.
COMPUTATIONAL MATERIALS SCIENCE (2013)
Very high speed cutting of Ti-6A1-4V titanium alloy - change in morphology and mechanism of chip formation
G. Sutter et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)
Adiabatic shear banding and scaling laws in chip formation with application to cutting of Ti-6Al-4V
A. Molinari et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2013)
The effect of cutting speed and heat treatment on the fatigue life of Grade 5 and Grade 23 Ti-6Al-4V alloys
W. Niu et al.
MATERIALS & DESIGN (2013)
FEM mesh-dependence in cutting process simulations
Ravindra Ambati et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Finite element simulation of high-speed machining of titanium alloy (Ti-6Al-4V) based on ductile failure model
Guang Chen et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Implementation of a constitutive model in finite element method for intense deformation
E. Hosseini et al.
MATERIALS & DESIGN (2011)
FE-model for Titanium alloy (Ti-6Al-4V) cutting based on the identification of limiting shear stress at tool-chip interface
Yancheng Zhang et al.
INTERNATIONAL JOURNAL OF MATERIAL FORMING (2011)
Comparison of the machinabilities of Ti6Al4V and TIMETAL® 54M using uncoated WC-Co tools
M. Armendia et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
Finite element simulation for burr formation near the exit of orthogonal cutting
W. J. Deng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
Surface integrity of dry machined titanium alloys
A. Ginting et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
Computational modelling of 3D turning: Influence of edge micro-geometry on forces, stresses, friction and tool wear in PcBN tooling
Tugrul Oezel
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Machinability of titanium alloys (Ti6Al4V and Ti555.3)
P. -J. Arrazola et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis
J. P. Davim et al.
MATERIALS & DESIGN (2009)
A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti-6Al-4V
Madalina Calamaz et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Numerical and experimental study of dry cutting for an aeronautic aluminium alloy (A2024-T351)
Tarek Mabrouki et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Finite element simulation of conventional and high speed machining of Ti6Al4V alloy
Domenico Umbrello
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Finite element modeling the influence of edge roundness on the stress and temperature fields induced by high-speed machining
Tugrul Oezel et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
An FEM investigation into the behavior of metal matrix composites: Tool-particle interaction during orthogonal cutting
A. Pramanik et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Revisiting the fundamentals of metal cutting by means of finite elements and ductile fracture mechanics
P. A. R. Rosa et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
A contribution to a qualitative understanding of thermo-mechanical effects during chip formation in hard turning
T. Mabrouki et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Finite element investigation of the flow stress dependence of chip formation
M Bäker
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Experimental and numerical study of chip formation during straight turning of hardened AISI 4340 steel
S Belhadi et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2005)
Chip geometries during high-speed machining for orthogonal cutting conditions
G Sutter
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)
Modeling of the contact stress distribution at the tool-chip interface
VP Astakhov et al.
MACHINING SCIENCE AND TECHNOLOGY (2005)
Chip formation, cutting forces, and tool wear in turning of Zr-based bulk metallic glass
M Bakkal et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2004)
A FEM study on mechanisms of discontinuous chip formation in hard machining
YB Guo et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Adiabatic shear banding in high speed machining of Ti-6Al-4V: experiments and modeling
A Molinari et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2002)
Micro-structural analysis of chip formation during orthogonal machining of Al/SiCp composites
SS Joshi et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2001)
Material aspects of chip formation in HSC machining
H Schulz et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2001)
分享论文
