Article
Engineering, Civil
Kuifeng Zhao, Yufei Wang, Philip L. -F. Liu
Summary: This note provides guidelines for selecting appropriate analytical periodic water wave solutions based on two physical parameters. The guidelines are summarized in a graphic format and the dividing lines between applicable wave theories are determined by the nonlinearity and frequency dispersion ratios.
COASTAL ENGINEERING
(2024)
Article
Engineering, Marine
S. C. Mohapatra, Guedes Soares
Summary: An analytical model of moored floating flexible net cage systems was developed to study dynamics and wave loads. Results were compared with finite element analysis and experimental data, and various factors were analyzed for their effects on system performance. This study is important for the design of multiple floating fish cage systems in offshore aquaculture.
Article
Engineering, Marine
Xuyue Chen, Xu Du, Chengkai Weng, Jin Yang, Deli Gao, Dongyu Su, Gan Wang
Summary: This paper proposes a real-time drilling parameters optimization method for offshore large-scale cluster extended reach drilling based on intelligent optimization algorithm and machine learning. By establishing a ROP model with long short-term memory neurons, and combining genetic algorithm, differential evolution algorithm, and particle swarm algorithm, the method achieves real-time optimization of drilling parameters and significantly improves the ROP.
Article
Engineering, Marine
Jingxi Zhang, Junmin Mou, Linying Chen, Pengfei Chen, Mengxia Li
Summary: This paper proposes a cooperative control scheme for ship formation tracking based on Model Predictive Control. A predictive observer is designed to estimate the current motion states of the leader ship using delayed motion information. Comparative simulations demonstrate the effectiveness and robustness of the proposed controller.
Article
Engineering, Marine
George Dafermos, George Zaraphonitis
Summary: The survivability of damaged ships is of great importance and the regulatory framework is constantly updated. The introduction of the probabilistic damage stability framework has rationalized the assessment procedure. Flooding simulation tools can be used to investigate the dynamic response of damaged ships.
Article
Engineering, Marine
Xiao Yu, Wangjun Ren, Bukui Zhou, Li Chen, Xiangyun Xu, Genmao Ren
Summary: This study investigated and compared the compression responses and energy absorption capacities of coral sand and silica sand at a strain rate of approximately 1000 s-1. The results showed that coral sand had significantly higher energy absorption capacity than silica sand due to its higher compressibility. The study findings suggest that using poorly graded coral sand can improve its energy absorption capacity.
Article
Engineering, Marine
Yu Yao, Danni Zhong, Qijia Shi, Ji Wu, Jiangxia Li
Summary: This study proposes a 2DH numerical model based on Boussinesq equations to investigate the impact of dredging reef-flat sand on wave characteristics and wave-driven current. The model is verified through wave flume experiments and wave basin experiments, and the influences of incident wave conditions and pit morphological features on wave characteristics are examined.
Article
Engineering, Marine
I. -C Kim, G. Ducrozet, V. Leroy, F. Bonnefoy, Y. Perignon, S. Bourguignon
Summary: Previous research focused on the accuracy and efficiency of short-term wave fields in specific prediction zones, while we developed algorithms for continuous wave prediction based on the practical prediction zone and discussed important time factors and strategies to reduce computational costs.
Article
Engineering, Marine
Sung-Jae Kim, Chungkuk Jin, MooHyun Kim
Summary: This study investigates the dynamic behavior of a moored submerged floating tunnel (SFT) under tsunami-like waves through numerical simulations and sensitivity tests. The results show that design parameters significantly affect the dynamics of the SFT system and mooring tensions, with shorter-duration and higher-elevation tsunamis having a greater impact.
Article
Engineering, Marine
Ziya Peng, Yuelin Song, Ping Yang, Kang Hu
Summary: This study aims to investigate the mixed-mode fracture behavior of stiffened plates with inclined semi-elliptical surface cracks (ISSCs). A new numerical model is developed to analyze the fracture behavior using normalized stress intensity factors (SIFs). The findings show that stiffened plates have a significant restraint effect on large surface cracks, especially at the surface point.
Article
Engineering, Marine
Alba Ricondo, Laura Cagigal, Beatriz Perez-Diaz, Fernando J. Mendez
Summary: This research presents a site-specific metamodel based on the SWASH numerical model simulations, which can predict coastal hydrodynamic variables in a fast and efficient manner. The metamodel uses downscaled and dimensionality reduced synthetic database to accurately reproduce wave setup, wave heights associated with different frequency bands, and wave runup. This method has great potential in coastal risk assessments, early warning systems, and climate change projections.
Article
Engineering, Marine
Hangyuan Zhang, Wanli Yang, Dewen Liu, Xiaokun Geng, Wangyu Dai, Yuzhi Zhang
Summary: The deep-water bridge is more vulnerable to earthquake damage than the bridge standing in air. The larger blocking ratio has a significant impact on the added mass coefficient, which requires further comprehensive study. The generation mechanism of block effect is analyzed using numerical simulation software ANSYS Fluent. The results show that the recirculation zone with focus reduces the pressure on the back surface of the cylinder, resulting in the peak value of in-line force not occurring synchronously with the peak value of acceleration. The change in position and intensity of the recirculation zone with focus, as well as the change in water flow around the cylinder surface, are identified as the generation mechanism of the block effect, which has a 10% influence on the hydrodynamic force. The changing rule of the added mass coefficient with blocking ratio is discussed in detail, and a modification approach to the current added mass coefficient calculation method is suggested. Physical experiments are conducted to validate the modification approach, and the results show that it is accurate and can be used in further study and real practice.
Article
Engineering, Marine
Golnesa Karimi-Zindashti, Ozgur Kurc
Summary: This study examines the performance of an in-house code utilizing a deterministic vortex method on the rotation of circular and square cylinders. The results show that rotational motion reduces drag forces, suppresses fluctuating forces, and increases lift forces. The code accurately predicts vortex shedding suppression and identifies the emergence of near-field wakes in the flow over rotating square cylinders.
Article
Engineering, Marine
Muhamad Hasfanizam Mat Yazik, Mohd Hafiz Zawawi, Ali Najah Ahmed, Lariyah Mohd Sidek, Hidayah Basri, Farzad Ismail
Summary: This paper presents a one-way three-dimensional fluid-structure interaction simulation to analyze the performance of a static Savonius hydrokinetic turbine. The results indicate that the optimal rotor position for the highest coefficient of static torque is at 15 degrees. Increasing water velocity improves the turbine's static torque, while surface roughness has a negative effect on the static torque coefficient. Different materials exhibit different stress and deformation, highlighting the importance of materials selection in the early design process.
Article
Engineering, Marine
Dongyang Shang, Xiaopeng Li, Meng Yin, Sainan Zhou
Summary: The flexible single-link underwater manipulator (FSLUM) can perform various underwater tasks in autonomous underwater vehicles, playing a significant role in ocean exploration and development. This study proposes an improved sliding mode control strategy based on neural network identification to enhance the control accuracy of the FSLUM. Simulation and prototype tracking control experiments demonstrate that the proposed strategy achieves high tracking accuracy.
Article
Engineering, Marine
Meng Zhang, Lianghui Sun, Yaoguo Xie
Summary: The research proposes a method for online identification of wave bending and torsional moment in hull structures. For structures without large openings, the method optimizes sensor positions and establishes a mathematical model to improve accuracy. For structures with large openings, a joint dual-section monitoring method is proposed to simultaneously identify bending and torsional moments in multiple key cross sections.
Article
Engineering, Marine
Longming Chen, Shutao Li, Yeqing Chen, Dong Guo, Wanli Wei, Qiushi Yan
Summary: This study investigated the dynamic response characteristics and damage modes of pile wharves subjected to underwater explosions. The results showed that the main damaged components of the pile wharf were the piles, and inclined piles had a higher probability of moderate or more significant damage compared to vertical piles. The study also suggested that replacing inclined piles with alternative optimized structures benefits the blast resistance of pile wharves.
Article
Engineering, Marine
G. Clarindo, C. Guedes Soares
Summary: Environmental contours are constructed using the Inverse-First Order Reliability Method based on return periods. The paper proposes the use of the Burr distribution to model the marginal distribution of long-term significant wave heights. The newly implemented scheme results in different environmental contours compared to the reference approach.
Article
Engineering, Marine
Jayanta Shounda, Krishnendu Barman, Koustuv Debnath
Summary: This study investigates the double-average turbulence characteristics of combined wave-current flow over a rough bed with different spacing arrangements. The results show that a spacing ratio of p/r=4 offers the highest resistance to the flow, and the double-average Reynolds stress decreases throughout the flow depth. The advection of momentum-flux of normal stress shows an increase at the outer layer and a decrease near the bed region after wave imposition. Maximum turbulence kinetic energy production and diffusion occur at different layers. The turbulence structure is strongly anisotropic at the bottom region and near the outer layer, with a decrease in anisotropy observed with an increase in roughness spacing.
Article
Engineering, Marine
Hang Xie, Xianglin Dai, Fang Liu, Xinyu Liu
Summary: This study investigates the load characteristics of a three-dimensional stern model with pitch angle through a drop test, and reveals complex characteristics of pressure distribution near the stern shaft. The study also shows that the vibration characteristics of the load are influenced by the drop height and pitch angle, with the drop height having a greater effect on the high-frequency components.