Related references
Note: Only part of the references are listed.Modelling for the dynamic recrystallization evolution of Ti-6Al-4V alloy in two-phase temperature range and a wide strain rate range
Guo-zheng Quan et al.
COMPUTATIONAL MATERIALS SCIENCE (2015)
Prediction of machining induced microstructure in Ti-6Al-4V alloy using 3-D FE-based simulations: Effects of tool micro-geometry, coating and cutting conditions
Yigit M. Arisoy et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Finite element modeling of microstructural changes in dry and cryogenic cutting of Ti6Al4V alloy
Giovanna Rotella et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2014)
Investigation of surface integrity in dry machining of Inconel 718
Domenico Umbrello
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Finite element modeling of microstructural changes in turning of AA7075-T651 Alloy
G. Rotella et al.
JOURNAL OF MANUFACTURING PROCESSES (2013)
Effect of Severe Plastic Deformation in Machining Elucidated via Rate-Strain-Microstructure Mappings
S. Shekhar et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2012)
Microstructure evolution of adiabatic shear bands and mechanisms of saw-tooth chip formation in machining Ti6Al4V
Z. P. Wan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Modeling of grain refinement in aluminum and copper subjected to cutting
Hongtao Ding et al.
COMPUTATIONAL MATERIALS SCIENCE (2011)
FEM mesh-dependence in cutting process simulations
Ravindra Ambati et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Finite element simulation of high-speed machining of titanium alloy (Ti-6Al-4V) based on ductile failure model
Guang Chen et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Effect of hot working and post-deformation heat treatment on microstructure and tensile properties of Ti-6Al-4V alloy
S. M. Abbasi et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2011)
Fabrication and oxidation resistance of nanocrystalline Fe10Cr alloy
Rajeev K. Gupta et al.
JOURNAL OF MATERIALS SCIENCE (2010)
Effect of hot working on flow behavior of Ti-6Al-4V alloy in single phase and two phase regions
A. Momeni et al.
MATERIALS & DESIGN (2010)
Material flow stress and failure in multiscale machining titanium alloy Ti-6Al-4V
J. Sun et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
Formation of ultra-fine grained materials by machining and the characteristics of the deformation fields
W. J. Deng et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Controlling gradation of surface strains and nanostructuring by large-strain machining
R. Calistes et al.
SCRIPTA MATERIALIA (2009)
Corrosion of pure Mg as a function of grain size and processing route
C. op't Hoog et al.
ADVANCED ENGINEERING MATERIALS (2008)
A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti-6Al-4V
Madalina Calamaz et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Severe plastic deformation (SPD) and nanostructured materials by machining
Srinivasan Swaminathan et al.
JOURNAL OF MATERIALS SCIENCE (2007)
Microstructural evolution of a Ti-6Al-4V alloy during β-phase processing:: experimental and simulative investigations
R Ding et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Testing and modelling of material response to deformation in bulk metal forming
PF Bariani et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2004)
Share Paper
