Related references
Note: Only part of the references are listed.The optimum conditions for solid-state-prepared (Y3-xCex)Al5O12 phosphor using the Taguchi method
Chuen-Shii Chou et al.
ADVANCED POWDER TECHNOLOGY (2012)
Investigating cooling curve profile and microstructure of a squeeze cast Al-4%Cu alloy
K. M. Amin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)
Effects of rheo-squeeze casting parameters on microstructure and mechanical properties of AlCuMnTi alloy
Wei Dai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Optimization of AZ80 magnesium alloy squeeze cast process parameters using morphological matrix
Guo Zhi-hong et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2012)
Influence of applied pressure on microstructure and tensile properties of squeeze cast magnesium Mg-Al-Ca alloy
Mohsen Masoumi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Optimization of heat exchangers with vortex-generator fin by Taguchi method
M. Zeng et al.
APPLIED THERMAL ENGINEERING (2010)
Employing the Taguchi method to obtain the optimum conditions of coagulation-flocculation process in tannery wastewater treatment
S. Aber et al.
CHEMICAL ENGINEERING JOURNAL (2010)
Effect of squeeze casting parameters on the mechanical properties of AZ91-Ca Mg alloys
C. S. Goh et al.
MATERIALS & DESIGN (2010)
Experimental determination of heat transfer coefficients during squeeze casting of aluminium
J. O. Aweda et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Thermal-flow techniques for sub-35 nm contact-hole fabrication using Taguchi method in electron-beam lithography
Te-Sheng Li et al.
MICROELECTRONIC ENGINEERING (2009)
Optimization of tensile properties of evaporative pattern casting process through Taguchi's method
Sudhir Kumar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Process parameters optimization for friction stir welding of RDE-40 aluminium alloy using Taguchi technique
A. K. Lakshminarayanan et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2008)
Preparation of semi-solid slurry containing fine and globular particles for wrought aluminum alloy 2024
Guo Hong-min et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2007)
Modelling and multi objective optimization of LM24 aluminium alloy squeeze cast process parameters using genetic algorithm
P. Vijian et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Optimization of squeeze cast parameters of LM6 aluminium alloy for surface roughness using Taguchi method
P. Vijian et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Effects of squeeze casting parameters on density, macrostructure and hardness of LM13 alloy
A. Maleki et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Properties of alumina particulate reinforced aluminum alloy produced by pressure die casting
H Sevik et al.
MATERIALS & DESIGN (2006)
Effects of Si content on defect band formation in hypoeutectic Al-Si die castings
HI Laukli et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Experimental study of squeeze casting of gunmetal
P Vijian et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
The effect of casting temperature on the properties of squeeze cast aluminium and zinc alloys
LJ Yang
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Die casting process optimization using Taguchi methods
GP Syrcos
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Evaluation and optimisation of integrated manufacturing system operations using Taguch's experiment design in computer simulation
CS Tsai
COMPUTERS & INDUSTRIAL ENGINEERING (2002)
Squeeze casting: an overview
MR Ghomashchi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
Share Paper
