Related references
Note: Only part of the references are listed.Comparison of tool wear mechanisms and surface integrity for dry and wet micro-drilling of nickel-base superalloys
Muhammad Imran et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2014)
Optimization of micro-EDM drilling of inconel 718 superalloy
Mustafa Ay et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Assessment of machining performance using the wear map approach in micro-drilling
Muhammad Imran et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Evaluation of surface integrity in micro drilling process for nickel-based superalloy
Muhammad Imran et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Sequential laser and mechanical micro-drilling of Ni superalloy for aerospace application
M. M. Okasha et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2010)
Statistical analysis of recast formation in laser drilled acute blind holes in CMSX-4 nickel superalloy
Stephen Leigh et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
The sensitivity of Ni-based superalloy to hole making operations: Influence of process parameters on subsurface damage and residual stress
J. Kwong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718
Thomas R. Newton et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Workpiece surface roughness and integrity after WEDM of Ti-6Al-4V and Inconel 718 using minimum damage generator technology
D. K. Aspinwall et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)
Laser beam machining - A review
Avanish Kumar Dubey et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Tool life and surface integrity aspects when drilling and hole making in Inconel 718
A. R. C. Sharman et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
An experimental investigation of deep-hole microdrilling capability for a nickel-based superalloy
M. Imran et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2008)
Influence of EDM process parameters in deep hole drilling of Inconel 718
P. Kuppan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2008)
Some considerations on tool wear and workpiece surface quality of holes finished by reaming or milling in a nickel base superalloy
D. A. Axinte et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2007)
Investigating the recast layer formed during the laser trepan drilling of Inconel 718 using the Taguchi method
Wen-Tung Chien et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
Effect of beam angle on HAZ, recast and oxide layer characteristics in laser drilling of TBC nickel superalloys
H. K. Sezer et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Surface and sub-surface quality of steel after EDM
P Bleys et al.
ADVANCED ENGINEERING MATERIALS (2006)
Micro-burr formation and minimization through process control
KH Lee et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2005)
Laser drilling of microholes in refractory alloys
VA Serebryakov et al.
JOURNAL OF OPTICAL TECHNOLOGY (2005)
Geometrical features and metallurgical characteristics of Nd:YAG laser drilled holes in thick IN718 and Ti-6Al-4V sheets
S Bandyopadhyay et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
Challenges facing surface engineering technologies in the cutting tool industry
SR Bradbury et al.
VACUUM (2000)
Share Paper
