Related references
Note: Only part of the references are listed.A new process of forming metallic bipolar plates for PEM fuel cell with pin-type pattern
M. Belali-Owsia et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Improvement of formability for fabricating thin continuously corrugated structures in sheet metal forming process
Sung-Woo Choi et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2012)
Design, Optimization, and Fabrication of Slotted-Interdigitated Thin Metallic Bipolar Plates for PEM Fuel Cells
Linfa Peng et al.
JOURNAL OF FUEL CELL SCIENCE AND TECHNOLOGY (2011)
Polymer Electrolyte Membrane Fuel Cell (PEMFC) Flow Field Plate: Design, Materials and Characterisation
P. J. Hamilton et al.
FUEL CELLS (2010)
Fabrication of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cell by Flexible Forming Process-Numerical Simulations and Experiments
Linfa Peng et al.
JOURNAL OF FUEL CELL SCIENCE AND TECHNOLOGY (2010)
Studies of the deformation styles of the rubber-pad forming process used for manufacturing metallic bipolar plates
Yanxiong Liu et al.
JOURNAL OF POWER SOURCES (2010)
Effect of manufacturing processes on formability and surface topography of proton exchange membrane fuel cell metallic bipolar plates
Sasawat Mahabunphachai et al.
JOURNAL OF POWER SOURCES (2010)
Corrosion resistance characteristics of stamped and hydroformed proton exchange membrane fuel cell metallic bipolar plates
F. Dundar et al.
JOURNAL OF POWER SOURCES (2010)
A review of metal separator plate materials suitable for automotive PEM fuel cells
N. de las Heras et al.
ENERGY & ENVIRONMENTAL SCIENCE (2009)
Feasibility investigations on a novel micro-manufacturing process for fabrication of fuel cell bipolar plates: Internal pressure-assisted embossing of micro-channels with in-die mechanical bonding
Mummer Koc et al.
JOURNAL OF POWER SOURCES (2007)
Metal bipolar plates for PEM fuel cell - A review
H. Tawfik et al.
JOURNAL OF POWER SOURCES (2007)
Cost-benefit analysis of commercial bipolar plates for PEMFC's
K. Jayakumar et al.
JOURNAL OF POWER SOURCES (2006)
Bipolar plates for PEM fuel cells: A review
A Hermann et al.
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2005)
Review of bipolar plates in PEM fuel cells: Flow-field designs
XG Li et al.
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2005)
Optimizing tube hydroforming using process simulation and experimental verification
Y Aue-U-Lan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Characteristics of composite bipolar plates for polymer electrolyte membrane fuel cells
EA Cho et al.
JOURNAL OF POWER SOURCES (2004)
Some new features in the development of metal forming technology
SH Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Hydroforming highlights: sheet hydroforming and tube hydroforming
LH Lang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Investigation of factors which cause breakage during the hydroforming of an automotive part
T Hama et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Numerical simulation of springback using enhanced assumed strain elements
QV Bui et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Bipolar plates for PEM fuel cells
E Middelman et al.
JOURNAL OF POWER SOURCES (2003)
Stainless steel as bipolar plate material for polymer electrolyte membrane fuel cells
HL Wang et al.
JOURNAL OF POWER SOURCES (2003)
Review and analysis of PEM fuel cell design and manufacturing
V Mehta et al.
JOURNAL OF POWER SOURCES (2003)
Technical cost analysis for PEM fuel cells
I Bar-On et al.
JOURNAL OF POWER SOURCES (2002)
Metallic bipolar plates for PEM fuel cells
J Wind et al.
JOURNAL OF POWER SOURCES (2002)
Quantum jumps in the PEMFC science and technology from the 1960s to the year 2000 Part II. Engineering, technology development and application aspects
P Costamagna et al.
JOURNAL OF POWER SOURCES (2001)
Share Paper
