Related references
Note: Only part of the references are listed.Enhanced grain refinement and microhardness of Ti-Al-V alloy by electropulsing ultrasonic shock
Xiaoxin Ye et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
A transmission electron microscopy and three-dimensional atom probe study of the oxygen-induced fine microstructural features in as-sintered Ti-6Al-4V and their impacts on ductility
M. Yan et al.
ACTA MATERIALIA (2014)
Effect of recovering damage and improving microstructure in the titanium alloy strip under high-energy electropulses
Xiaoxin Ye et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
Microstructure, properties and temperature evolution of electro-pulsing treated functionally graded Ti-6Al-4V alloy strip
Xiaoxin Ye et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
被撤回的出版物: Effect of electropulsing treatment on the microstructure, texture, and mechanical properties of cold-rolled Ti-6Al-4V alloy (Retracted article. See vol. 33, pg. 1699, 2018)
Xiaoxin Ye et al.
JOURNAL OF MATERIALS RESEARCH (2014)
Effect of electropulsing treatment and ultrasonic striking treatment on the mechanical properties and microstructure of biomedical ti-6Al-4V alloy
Xiaoxin Ye et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2014)
Subtransus triplex heat treatment of laser melting deposited Ti-5Al-5Mo-5V-1Cr-1Fe near β titanium alloy
C. M. Liu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Reduction in anisotropy of mechanical properties of coilable (α plus β)-type titanium alloy thin sheet through simple heat treatment for use in next-generation aircraft applications
Masaaki Nakai et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Microhardness and corrosion behavior of surface gradient oxide coating on the titanium alloy strips under high energy electro-pulsing treatment
Xiaoxin Ye et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Properties of Titanium Foams for Biomedical Applications
Louis-Philippe Lefebvre et al.
ADVANCED ENGINEERING MATERIALS (2013)
Design, Processing, Microstructure, Properties, and Applications of Advanced Intermetallic TiAl Alloys
Helmut Clemens et al.
ADVANCED ENGINEERING MATERIALS (2013)
Thermoelectric n-type silicon germanium synthesized by unidirectional solidification in microgravity
Takeshi Okutani et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2013)
FEM based prediction of phase transformations during Friction Stir Welding of Ti6Al4V titanium alloy
Gianluca Buffa et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Microstructure and mechanical properties of AZ61 alloys with large cross-sectional size fabricated by multi-pass ECAP
Jufu Jiang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Evolution of Texture and Microstructure in Commercially Pure Titanium with Change in Strain Path During Rolling
N. P. Gurao et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Biomimetic Titanium Alloy with Sparsely Distributed Nanotubes Could Enhance Osteoblast Functions
Shenglin Mei et al.
ADVANCED ENGINEERING MATERIALS (2012)
Determination of Minimum Machining Depth After Heat Treatment of ASTM Grade 2 Titanium Alloy
Richard G. Dobeson et al.
ADVANCED ENGINEERING MATERIALS (2012)
Properties, microstructure and texture evolution of cold rolled Cu strips under electropulsing treatment
R. F. Zhu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2012)
Preparation and properties of enhanced bulk nanoporous coppers
Qing Yang et al.
MATERIALS LETTERS (2012)
In Situ Synthesis of Ti5Si3 Matrix Nanocomposites Reinforced with Nanoparticles by High-Energy Mechanical Alloying
Chuang Li et al.
ADVANCED ENGINEERING MATERIALS (2011)
Wedge indentation into elastic-plastic single crystals, 1: Asymptotic fields for nearly-flat wedge
Y. Saito et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2011)
Solid solution strengthening in polycrystals of Mg-Sn binary alloys
B. Q. Shi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2011)
Effect of thermo-electropulsing rolling on mechanical properties and microstructure of AZ31 magnesium alloy
Haoming Liao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Kinetics of Delta-Ferrite to Austenite Phase Transformation in a Two-Phase Fe-Al-C Alloy
Tihe Zhou et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2011)
Evolution of dislocation substructures in fatigue loaded and failed stainless steel with the intermediate electropulsing treatment
S. V. Konovalov et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
On the thermodynamics and kinetics of electropulsing induced dissolution of β-Mg17Al12 phase in an aged Mg-9Al-1Zn alloy
Yanbin Jiang et al.
ACTA MATERIALIA (2009)
Morphology-controlled synthesis of SrWO4 crystals
Eun-Kyoung Ryu et al.
MATERIALS LETTERS (2008)
Research of electroplastic rolling of AZ31 Mg alloy strip
Zhuohui Xu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Using cluster dynamics to model electrical resistivity measurements in precipitating AIR alloys
Emmanuel Clouet et al.
ACTA MATERIALIA (2007)
Deformation behavior of dispersion-strengthened copper at high temperature
Wang Mengjun et al.
RARE METALS (2006)
TEM characterization of plate-shaped L12-(Al,Ag)3Ti precipitates in a Ag-modified TiAl based intermetallics
Y. Yuan et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2006)
Correlation of the microstructure and mechanical properties of oxide-dispersion-strengthened coppers fabricated by internal oxidation
J Lee et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)
Titanium alloys for aerospace applications
M Peters et al.
ADVANCED ENGINEERING MATERIALS (2003)
Equilibrium solid solubility of silicon in silver
L Weber
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2002)
Share Paper
