Related references
Note: Only part of the references are listed.Experimental study on micro electrical discharge machining of porous stainless steel
Kan Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Machining performance optimization for electro-discharge machining of Inconel 601, 625, 718 and 825: an integrated optimization route combining satisfaction function, fuzzy inference system and Taguchi approach
Rahul et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
An experimental investigation emphasizing surface characteristics of electro-discharge-machined Inconel 601
Chandramani Upadhyay et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
Metallurgical Approach Towards Explaining Optimized EDM Process Parameters for Better Surface Integrity of AISI D2 Tool Steel
Debasis Nayak et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)
EDM machinability and surface roughness analysis of INCONEL 600 using graphite electrodes
A. Torres et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Experimental investigation of kerf of Ti6Al4V exposed to different heat treatment processes in WEDM and optimization of parameters using genetic algorithm
Mehmet Altug et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Parametric modeling and optimization for wire electrical discharge machining of Inconel 718 using response surface methodology
Vivek Aggarwal et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
EXPERIMENTAL INVESTIGATION ON ELECTRICAL DISCHARGE DRILLING OF Ti-6Al-4V ALLOY
Umacharan Singh Yadav et al.
MACHINING SCIENCE AND TECHNOLOGY (2015)
Study on the influence of micro-EDM process parameters during machining of Ti-6Al-4V superalloy
A. P. Tiwary et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Experimental investigations on the microhole machining of 304 stainless steel by micro-EDM process using RC-type pulse generator
N. Natarajan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
An experimental investigation on surface finish in die-sinking EDM of Ti-5Al-2.5Sn
Md Ashikur Rahman Khan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Effect of dielectric fluid with surfactant and graphite powder on Electrical Discharge Machining of titanium alloy using Taguchi method
Murahari Kolli et al.
ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2015)
Process performance of micro-EDM drilling of stainless steel
G. D'Urso et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Performance and Surface Integrity of Ti6Al4V After Sinking EDM with Special Graphite Electrodes
Fred L. Amorim et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Analysis of Form Tolerances in Electrical Discharge Machining Process for Inconel 718 and 625
S. Dhanabalan et al.
MATERIALS AND MANUFACTURING PROCESSES (2014)
Experimental Investigation and Analysis of EDM Characteristics of Inconel 825
Aveek Mohanty et al.
MATERIALS AND MANUFACTURING PROCESSES (2014)
Modeling and analysis of micro-WEDM process of titanium alloy (Ti-6Al-4V) using response surface approach
P. Sivaprakasam et al.
ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2014)
Optimization of micro-EDM drilling of inconel 718 superalloy
Mustafa Ay et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Optimization of micro milling electrical discharge machining of Inconel 718 by Grey-Taguchi method
Mao-yong Lin et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2013)
Surface treatment by electric discharge machining of Ti-6Al-4V alloy for potential application in orthopaedics
Petr Harcuba et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2012)
INFLUENCE OF MACHINE FEED RATE IN WEDM OF TITANIUM Ti-6Al-4V WITH CONSTANT CURRENT (6A) USING BRASS WIRE
Aniza Alias et al.
INTERNATIONAL SYMPOSIUM ON ROBOTICS AND INTELLIGENT SENSORS 2012 (IRIS 2012) (2012)
The effect of microstructure on fatigue performance of Ti-6Al-4V alloy after EDM surface treatment for application in orthopaedics
Josef Strasky et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2011)
Optimization of the EDM parameters on machining Ti-6Al-4V with multiple quality characteristics
J. Y. Kao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy
G. Kibria et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Neuro-fuzzy and neural network-based prediction of various responses in electrical discharge machining of AISI D2 steel
Mohan Kumar Pradhan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718
Thomas R. Newton et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Modeling and multi-response optimization of Inconel 718 on machining of CNCWEDM process
R. Ramakrishnan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Residual stresses and white layer in electric discharge machining (EDM)
Buelent Ekmekci
APPLIED SURFACE SCIENCE (2007)
Electrical discharge machining of titanium alloy (Ti-6Al-4V)
Ahmet Hascalik et al.
APPLIED SURFACE SCIENCE (2007)
A comparative study of surface integrity of Ti-6Al-4V alloy machined by EDM and AECG
Ahmet Hascalik et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Modelling the machining parameters of wire electrical discharge machining of Inconel 601 using RSM
MS Hewidy et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
An index to evaluate the wear resistance of the electrode in micro-EDM
YY Tsai et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Effect of electrical discharge machining on surface characteristics and machining damage of AISI D2 tool steel
YH Guu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
State of the art electrical discharge machining (EDM)
KH Ho et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)
Machining characteristics of titanium alloy (Ti-6Al-4V) using a combination process of EDM with USM
YC Lin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
Share Paper
