Related references
Note: Only part of the references are listed.Influence of surface topography on torsional fretting wear under flat-on-flat contact
Wenlong Lu et al.
TRIBOLOGY INTERNATIONAL (2017)
Influence of surface preparation on surface topography and tribological behaviours
Andrzej Dzierwa
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2017)
Adsorption Mechanism of Cu-Doped SnO2 (110) Surface toward H-2 Dissolved in Power Transformer
Feng Wang et al.
JOURNAL OF NANOMATERIALS (2016)
Effect of roughness on the wear behavior of HVOF coatings dry sliding against a friction material
Matteo Federici et al.
WEAR (2016)
Improving surface properties and wear behaviors of duplex stainless steel via pressure carburizing
Sharidah Azuar Abdul Azis et al.
SURFACE & COATINGS TECHNOLOGY (2012)
Correlation between standard roughness parameters skewness and kurtosis and tribological behaviour of contact surfaces
Marko Sedlacek et al.
TRIBOLOGY INTERNATIONAL (2012)
Experimental characterization of friction coefficient at the tool-chip-workpiece interface during dry cutting of AISI 1045
H. Ben Abdelali et al.
WEAR (2012)
Identification of Subsurface Deformation in Machining of Inconel 718
Jinming Zhou et al.
MATERIALS AND COMPUTATIONAL MECHANICS, PTS 1-3 (2012)
Interfacial separation between elastic solids with randomly rough surfaces: Comparison between theory and numerical techniques
A. Almqvist et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2011)
Surface Topography Modelling for Reduced Friction
Marko Sedlacek et al.
STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING (2011)
Surface morphology in engineering applications: Influence of roughness on sliding and wear in dry fretting
K. J. Kubiak et al.
TRIBOLOGY INTERNATIONAL (2011)
Enhanced chromizing kinetics of tool steel by means of surface mechanical attrition treatment
S. D. Lu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Identification of a friction model-Application to the context of dry cutting of an AISI 1045 annealed steel with a TiN-coated carbide tool
J. Rech et al.
TRIBOLOGY INTERNATIONAL (2009)
Friction and wear properties of short carbon fiber reinforced aluminum matrix composites
Liu Lei et al.
WEAR (2009)
Influence of surface preparation on roughness parameters, friction and wear
M. Sedlacek et al.
WEAR (2009)
Fabrication of a gradient nano-micro-structured surface layer on bulk copper by means of a surface mechanical grinding treatment
W. L. Li et al.
SCRIPTA MATERIALIA (2008)
Elastic contact between rough surfaces: Effect of roughness at large and small wavelengths
Sangil Hyun et al.
TRIBOLOGY INTERNATIONAL (2007)
Characterization of machining of AISI 1045 steel over a wide range of cutting speeds. Part 2: evaluation of flow stress models and interface friction distribution schemes
S. A. Iqbal et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2007)
Finite element modeling of elasto-plastic contact between rough surfaces
L Pei et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2005)
Characterization of nanocrystalline ferrite produced by mechanical milling of pearlitic steel
S Ohsaki et al.
SCRIPTA MATERIALIA (2005)
Finite-element analysis of contact between elastic self-affine surfaces
S Hyun et al.
PHYSICAL REVIEW E (2004)
Sub-micrometer structures generated during dry machining of copper
H Ni et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Geometrically necessary boundaries, incidental dislocation boundaries and geometrically necessary dislocations
DA Hughes et al.
SCRIPTA MATERIALIA (2003)
An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment
NR Tao et al.
ACTA MATERIALIA (2002)
Elastoplastic contact between randomly rough surfaces
BNJ Persson
PHYSICAL REVIEW LETTERS (2001)
Microstructure and strength of nickel at large strains
DA Hughes et al.
ACTA MATERIALIA (2000)
Share Paper
