Related references
Note: Only part of the references are listed.Experimental investigation of the effect of temperature in semisolid casting using cooling slope method
Amin Kolahdooz et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING (2016)
Experimental investigation of thixoforging process on microstructure and mechanical properties of the centrifugal pump flange
A. Kazemi et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2015)
Experimental investigation of thixoforging parameters effects on the microstructure and mechanical properties of the helical gearbox cap
A. Kolahdooz et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2014)
Investigation of the controlled atmosphere of semisolid metal processing of A356 aluminium alloy
A. Kolahdooz et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2014)
Effect of sintering on wear characteristics of Fe-Al2O3 metal matrix composites
Pallav Gupta et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2014)
Structural and mechanical behaviour of 5% Al2O3-reinforced Fe metal matrix composites (MMCs) produced by powder metallurgy (P/M) route
Pallav Gupta et al.
BULLETIN OF MATERIALS SCIENCE (2013)
Optimization of semi-solid metal processing of A356 aluminum alloy
S. Nourouzi et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2013)
Hardness and Wear Behavior of CoO doped Fe-Al2O3 Metal Matrix Composite (MMC) Synthesized via Powder Metallurgy (P/M) Technique
Palley Gupta et al.
ADVANCES IN MATERIALS AND PROCESSING: CHALLENGES AND OPPORTUNITIES (2012)
Microstructure evolution of A356 aluminum alloy produced by cooling slope method
Selman Nourouzi et al.
ADVANCES IN METALLURGICAL AND MINING ENGINEERING (2012)
Deformation Behavior of Semisolid A356 Alloy Prepared by Low Temperature Pouring
Z. L. Ning et al.
MATERIALS AND MANUFACTURING PROCESSES (2010)
Numerical simulation of solidification of liquid aluminum alloy flowing on cooling slope
N. K. Kund et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2010)
Study on the effects of the length and angle of inclined plate on the thixotropic microstructure of A356 aluminum alloy
Farshid Taghavi et al.
MATERIALS & DESIGN (2009)
Study on the ability of mechanical vibration for the production of thixotropic microstructure in A356 aluminum alloy
F. Taghavi et al.
MATERIALS & DESIGN (2009)
An investigation on semi-solid Al-7Si-0.3Mg alloy produced by mechanical stirring
R Haghayeghi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Extrusion behavior of Al-Cu alloys in the semisolid state
BS Lee et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
The effect of isothermal mechanical stirring on an Al-Si alloy in the semisolid condition
K Sukumaran et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
The formation of rosette α phase, structural evolution during the reheating and semi-solid casting of AlSi7Mg alloy
YZ Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Application of resistance heating technique to mushy state forming of aluminium alloy
S Maki et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
The shear behaviour of partially solidified Al-Si-Cu alloys
T Sumitomo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)
Share Paper
