Related references
Note: Only part of the references are listed.A comparative study of transverse shrinkage stresses and residual stresses in P91 welded pipe including plasticity error
Chandan Pandey et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2018)
Study of the fracture surface morphology of impact and tensile tested cast and forged (C&F) Grade 91 steel at room temperature for different heat treatment regimes
Chandan Pandey et al.
ENGINEERING FAILURE ANALYSIS (2017)
Effect of diffusible hydrogen content on embrittlement of P92 steel
Nitin Saini et al.
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2017)
Diffusible Hydrogen Level in Deposited Metal and Their Effect on Tensile Properties and Flexural Strength of P91 Steel
Chandan Pandey et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2017)
Microstructure-based assessment of creep rupture behaviour of cast-forged P91 steel
Chandan Pandey et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Characterization of Microstructure of HAZs in As-Welded and Service Condition of P91 Pipe Weldments
C. Pandey et al.
METALS AND MATERIALS INTERNATIONAL (2017)
Characterization of Cast and Forged (C&F) Gr. 91 Steel in Different Heat Treatment Condition
C. Pandey et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)
Microstructure and mechanical property relationship for different heat treatment and hydrogen level in multi-pass welded P91 steel joint
Chandan Pandey et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Hydrogen induced cold cracking of creep resistant ferritic P91 steel for different diffusible hydrogen levels in deposited metal
Chandan Pandey et al.
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2016)
On the prediction of effect of direction of welding on bead geometry and residual deformation of double-sided fillet welds
C. Pandey et al.
INTERNATIONAL JOURNAL OF STEEL STRUCTURES (2016)
Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld
C. Pandey et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2016)
Effect of Heat Treatment on Microstructure and Hot Impact Toughness of Various Zones of P91 Welded Pipes
C. Pandey et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2016)
Microstructural characteristics and mechanical properties of underwater wet flux-cored wire welded 316L stainless steel joints
H. L. Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Identification and Characterization of Intercritical Heat-Affected Zone in As-Welded Grade 91 Weldment
Yiyu Wang et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
Thermomechanical Analysis of Preheat Effect on Grade P91 Steel During GTA Welding
M. Zubairuddin et al.
MATERIALS AND MANUFACTURING PROCESSES (2016)
Influence of Heat Treatment in Residual Stresses Generated in P91 Steel-pipe Weld
Tatiane Campos Chuvas et al.
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2015)
On the estimation of error in measuring the residual stress by strain gauge rosette
A. Giri et al.
MEASUREMENT (2015)
MICROSTRUCTURE AND MECHANICAL PROPERTIES OF AN UNDERWATER WET WELDED DISSIMILAR FERRITIC/AUSTENITIC STEEL JOINT
N. Guo et al.
STRENGTH OF MATERIALS (2015)
Investigation on heat-affected zone hydrogen-induced cracking of high-strength naval steels using the Granjon implant test HENRY GRANJON PRIZE 2014 Winner Category B: Materials Behaviour and Weldability
Xin Yue
WELDING IN THE WORLD (2015)
Residual stress distributions in a P91 steel-pipe girth weld before and after post weld heat treatment
S. Paddea et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Numerical investigation on residual stress distribution and evolution during multipass narrow gap welding of thick-walled stainless steel pipes
C. Liu et al.
FUSION ENGINEERING AND DESIGN (2011)
Creep behaviour of modified 9Cr-1Mo ferritic steel
B. K. Choudhary et al.
JOURNAL OF NUCLEAR MATERIALS (2011)
HYDROGEN-ASSISTED CRACKING SUSCEPTIBILITY of modified 9Cr-1Mo steel and its weld metal
S. K. Albert et al.
WELDING IN THE WORLD (2011)
A Comparison Between Measured and Modeled Residual Stresses in a Circumferentially Butt-Welded P91 Steel Pipe
A. H. Yaghi et al.
JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME (2010)
On the effect of long-term creep on the microstructure of a 12% chromium tempered martensite ferritic steel
A. Aghajani et al.
ACTA MATERIALIA (2009)
Numerical prediction and neutron diffraction measurement of the residual stresses for a modified 9Cr-1Mo steel weld
Seok-Hoon Kim et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Influence of welding sequence on welding distortions in pipes
I. Sattari-Far et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2008)
Improvement of Weld Characteristics by Variation in Welding Processes and Parameters in Joining of Thick Wall 304LN Stainless Steel Pipe
Shrirang Kulkarni et al.
ISIJ INTERNATIONAL (2008)
Evaluation of dynamic fracture toughness based reference temperature (T0dy() of modified 9Cr-1Mo steel in phosphorus embrittled and cold-worked condition
S. Sathyanarayanan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Type IV cracking in ferritic power plant steels
J. A. Francis et al.
MATERIALS SCIENCE AND TECHNOLOGY (2006)
Three-dimensional finite element analysis to predict the effects of SAW process parameters on temperature distribution and angular distortions in single-pass butt joints with top and bottom reinforcements
M. M. Mahapatra et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2006)
Prediction of welding residual stress in multi-pass butt-welded modified 9Cr-1Mo steel pipe considering phase transformation effects
Deng Dean et al.
COMPUTATIONAL MATERIALS SCIENCE (2006)
Residual stresses and distortions in welded structures: a perspective for engineering applications
P Dong
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2005)
Numerical modeling and experimental investigation on the characteristics of molten pool during laser processing
LX Yang et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2001)
Residual stress analyses of a multi-pass girth weld: 3-D special shell versus axisymmetric models
P Dong
JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME (2001)
Share Paper
