Related references
Note: Only part of the references are listed.Microstructure and mechanical properties of double-wire plus arc additively manufactured Al-Cu-Mg alloys
Zewu Qi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Deformation microstructures and strengthening mechanisms for the wire plus arc additively manufactured Al-Mg4.5Mn alloy with inter-layer rolling
Jianglong Gu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Wire arc additive manufacturing of Al-6Mg alloy using variable polarity cold metal transfer arc as power source
Chen Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Fracture toughness and fatigue crack growth rate properties in wire plus arc additive manufactured Ti-6Al-4V
X. Zhang et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2017)
Investigations into effect of weld-deposition pattern on residual stress evolution for metallic additive manufacturing
M. A. Somashekara et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
A comparative study of GMAW- and DE-GMAW-based additive manufacturing techniques: thermal behavior of the deposition process for thin-walled parts
Dongqing Yang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Geometric Limitation and Tensile Properties of Wire and Arc Additive Manufacturing 5A06 Aluminum Alloy Parts
Haibin Geng et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)
Investigation of mechanical properties for hybrid deposition and micro-rolling of bainite steel
Youheng Fu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Optimization of wire feed for GTAW based additive manufacturing
Haibin Geng et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Characterization the contribution and limitation of the characteristic processing parameters in cold metal transfer deposition of an Al alloy
Peng Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition
Jun Xiong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Formability of a wire arc deposited aluminium alloy
C. M. A. Silva et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
Application of bulk deformation methods for microstructural and material property improvement and residual stress and distortion control in additively manufactured components
Paul A. Colegrove et al.
SCRIPTA MATERIALIA (2017)
Studies on Dissimilar Twin-Wire Weld-Deposition for Additive Manufacturing Applications
M. A. Somashekara et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)
Evaluation and Optimization of a Hybrid Manufacturing Process Combining Wire Arc Additive Manufacturing with Milling for the Fabrication of Stiffened Panels
Fang Li et al.
APPLIED SCIENCES-BASEL (2017)
A Comparative Study of Additively Manufactured Thin Wall and Block Structure with Al-6.3%Cu Alloy Using Cold Metal Transfer Process
Baoqiang Cong et al.
APPLIED SCIENCES-BASEL (2017)
Preliminary development of a Wire and Arc Additive Manufacturing system (WAAM)
J. L. Prado-Cerqueira et al.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE 2017 (MESIC 2017) (2017)
Additive manufacturing of metals
Dirk Herzog et al.
ACTA MATERIALIA (2016)
Additive construction: State-of-the-art, challenges and opportunities
Nathalie Labonnote et al.
AUTOMATION IN CONSTRUCTION (2016)
Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
Mary Kathryn Thompson et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)
Forming appearance control of arc striking and extinguishing area in multi-layer single-pass GMAW-based additive manufacturing
Jun Xiong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Investigations on the parametric effects of cold metal transfer process on the microstructural aspects in AA6061
Nalajam Pavan Kumar et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2016)
Adaptive path planning for wire-feed additive manufacturing using medial axis transformation
Donghong Ding et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Additive manufacturing and sustainability: an exploratory study of the advantages and challenges
Simon Ford et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Forming characteristics of thin-wall steel parts by double electrode GMAW based additive manufacturing
Dongqing Yang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys
Jianglong Gu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
The effectiveness of combining rolling deformation with Wire-Arc Additive Manufacture on β-grain refinement and texture modification in Ti-6Al-4V
J. Donoghue et al.
MATERIALS CHARACTERIZATION (2016)
The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al-6.3Cu alloy
Jianglong Gu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Wire plus Arc Additive Manufacturing
S. W. Williams et al.
MATERIALS SCIENCE AND TECHNOLOGY (2016)
Microstructure and mechanical property considerations in additive manufacturing of aluminum alloys
Y. Ding et al.
MRS BULLETIN (2016)
Crack path selection at the interface of wrought and wire plus arc additive manufactured Ti-6Al-4V
Jikui Zhang et al.
MATERIALS & DESIGN (2016)
A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti-6Al-4V components
Blanka A. Szost et al.
MATERIALS & DESIGN (2016)
Fatigue crack propagation behaviour in wire plus arc additive manufactured Ti-6Al-4V: Effects of microstructure and residual stress
Jikui Zhang et al.
MATERIALS & DESIGN (2016)
Optimization of WAAM deposition patterns for T-crossing features
Giuseppe Venturini et al.
5TH CIRP GLOBAL WEB CONFERENCE - RESEARCH AND INNOVATION FOR FUTURE PRODUCTION (CIRPE 2016) (2016)
Process planning for additive and subtractive manufacturing technologies
Stephen T. Newman et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2015)
Forming appearance analysis in multi-layer single-pass GMAW-based additive manufacturing
Jun Xiong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Microstructure of Interpass Rolled Wire plus Arc Additive Manufacturing Ti-6Al-4V Components
Filomeno Martina et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)
Donghong Ding et al.
ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2015)
Effectiveness of cold metal transfer process for welding 7075 aluminium alloys
A. Elrefaey
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2015)
Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3% Cu alloy
Baoqiang Cong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
A tool-path generation strategy for wire and arc additive manufacturing
Donghong Ding et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Adaptive control of deposited height in GMAW-based layer additive manufacturing
Jun Xiong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
Mechanical and microstructural properties of robotic Cold Metal Transfer (CMT) welded 5083-H111 and 6082-T651 aluminum alloys
Beytullah Gungor et al.
MATERIALS & DESIGN (2014)
A study of cold metal transfer clads in nickel-base INCONEL 718 superalloy
O. T. Ola et al.
MATERIALS & DESIGN (2014)
Effect of GMAW-CMT Heat Input on Weld Bead Profile Geometry for Freeform Fabrication of Aluminium Parts
Abdullah Wagiman et al.
4TH MECHANICAL AND MANUFACTURING ENGINEERING, PTS 1 AND 2 (2014)
High pressure interpass rolling of Wire plus Arc Additively Manufactured titanium components
Paul A. Colegrove et al.
RESIDUAL STRESSES IX (2014)
Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling
Paul A. Colegrove et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Online measurement of bead geometry in GMAW-based additive manufacturing using passive vision
Jun Xiong et al.
MEASUREMENT SCIENCE AND TECHNOLOGY (2013)
Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V
Fude Wang et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Fabrication of geometrical features using wire and arc additive manufacture
Panagiotis Kazanas et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2012)
Thermal Science of Weld Bead Defects: A Review
P. S. Wei
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME (2011)
Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding
C. G. Pickin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)
The effects of Prandtl number on wavy weld boundary
P. S. Wei et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2009)
The mechanical effects of deposition patterns in welding-based layered manufacturing
M. P. Mughal et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2007)
Evaluation of cold metal transfer (CMT) process for welding aluminium alloy
C. G. Pickin et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2006)
3D welding and milling: part II - optimization of the 3D welding process using an experimental design approach
YA Song et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)
The humping phenomenon during high speed gas metal arc welding
TC Nguyen et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2005)
Rapid prototyping of 4043 Al-alloy parts by VP-GTAW
HJ Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Weld deposition-based rapid prototyping: a preliminary study
YM Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Automated system for welding-based rapid prototyping
YM Zhang et al.
MECHATRONICS (2002)
Overview -: Residual stress part 1 -: Measurement techniques
PJ Withers et al.
MATERIALS SCIENCE AND TECHNOLOGY (2001)
Overview -: Residual stress part 2 -: Nature and origins
PJ Withers et al.
MATERIALS SCIENCE AND TECHNOLOGY (2001)
Share Paper
