Related references
Note: Only part of the references are listed.Dispersoid particles precipitated during the solutionizing course of Al-12 wt %Si-4 wt%Cu-1.2 wt%Mn alloy and their influence on high temperature strength
Hengcheng Liao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
High- and low-cycle fatigue influence of silicon, copper, strontium and iron on hypo-eutectic Al-Si-Cu and Al-Si-Mg cast alloys used in cylinder heads
Patrik Huter et al.
INTERNATIONAL JOURNAL OF FATIGUE (2016)
Development of high performance near eutectic Al-Si-Mg alloy profile by micro alloying with Ti
Yuna Wu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2016)
Ageing characteristics and high-temperature tensile properties of Al-Si-Cu-Mg alloys with micro-additions of Cr, Ti, V and Zr
S. K. Shaha et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Effect of Mn and heat treatment on improvements in static strength and low-cycle fatigue life of an Al-Si-Cu-Mg alloy
S. K. Shaha et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Effects of Cu content and Cu/Mg ratio on the microstructure and mechanical properties of Al-Si-Cu-Mg alloys
Yan Zheng et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
The effects of Mg addition on the microstructure and mechanical properties of thixoformed Al-5%Si-Cu alloys
M. S. Salleh et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Dispersoid strengthening of a high temperature Al-Si-Cu-Mg alloy via Mo addition
A. R. Farkoosh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Enhanced mechanical properties of an Al-Si-Cu-Mg alloy at 300°C: Effects of Mg and the Q-precipitate phase
A. R. Farkoosh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Effect of heat treatment and Fe content on the microstructure and mechanical properties of die-cast Al-Si-Cu alloys
Hailin Yang et al.
MATERIALS & DESIGN (2015)
The effects of cooling rate and heat treatment on mechanical and thermal characteristics of Al-Si-Cu-Mg foundry alloys
S. W. Choi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
Physical modification of intermetallic phases in Al-Si-Cu alloys
J. Barbosa et al.
MATERIALS CHEMISTRY AND PHYSICS (2014)
Tensile Properties of Al-Cu 206 Cast Alloys with Various Iron Contents
K. Liu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Phase formation in as-solidified and heat-treated Al-Si-Cu-Mg-Ni alloys: Thermodynamic assessment and experimental investigation for alloy design
A. R. Farkoosh et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2013)
Microstructures and mechanical properties of heat-treated Al-5.0Cu-0.5Fe squeeze cast alloys with different Mn/Fe ratio
Weiwen Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
The effects of manganese on the T-phase and creep resistance in Al-Si-Cu-Mg-Ni alloys
A. R. Farkoosh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Influence of Mg and solution heat treatment on the occurrence of incipient melting in Al-Si-Cu-Mg cast alloys
A. M. A. Mohamed et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Eutectic Al-Si-Cu-Fe-Mn alloys with enhanced mechanical properties at room and elevated temperature
E. R. Wang et al.
MATERIALS & DESIGN (2011)
Influence of additives on the microstructure and tensile properties of near-eutectic Al-10.8%Si cast alloy
A. M. A. Mohamed et al.
MATERIALS & DESIGN (2009)
Effects of trace Mn addition on the elevated temperature tensile strength and microstructure of a low-iron Al-Si piston alloy
Zhao Qian et al.
MATERIALS LETTERS (2008)
Effect of Zr addition on the aging behavior of A319 aluminum cast alloy
P Sepehrband et al.
SCRIPTA MATERIALIA (2005)
Correlation between mechanical properties and amount of dendritic α-Al phase in as-cast near-eutectic Al-11.6% Si alloys modified with strontium
HC Liao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)
Study on wear properties of aluminium-silicon piston alloy
MM Haque et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Share Paper
