Related references
Note: Only part of the references are listed.Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization
Ashish Kumar Singh et al.
JOM (2018)
Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments
Ashish Kumar Singh et al.
JOM (2018)
Development of glass microballoon/HDPE syntactic foams by compression molding
M. L. Jayavardhan et al.
COMPOSITES PART B-ENGINEERING (2017)
An Investigation of burrs, chip formation, hole size, circularity and delamination during drilling operation of GLARE using ANOVA
Khaled Giasin et al.
COMPOSITE STRUCTURES (2017)
Influence of cooling on the performance of the drilling process of glass fibre reinforced epoxy composites
B. Ramesh et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2016)
Influence of workpiece constituents and cutting speed on the cutting forces developed in the conventional drilling of CFRP composites
Julian Luis Merino-Perez et al.
COMPOSITE STRUCTURES (2016)
Experimental investigation, prediction and optimization of cylindricity and perpendicularity during drilling of WCB material using grey relational analysis
Saurin Sheth et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2016)
Effect of Machining Parameters on Tool Wear and Hole Quality of AISI 316L Stainless Steel in Conventional Drilling
A. Z. Sultan et al.
2ND INTERNATIONAL MATERIALS, INDUSTRIAL, AND MANUFACTURING ENGINEERING CONFERENCE, MIMEC2015 (2015)
Applications of Polymer Matrix Syntactic Foams
Nikhil Gupta et al.
JOM (2014)
Experimental studies on hole quality and machinability characteristics in drilling of unreinforced and reinforced polyamides
V. N. Gaitonde et al.
JOURNAL OF COMPOSITE MATERIALS (2014)
Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates
Vijayan Krishnaraj et al.
COMPOSITES PART B-ENGINEERING (2012)
Surface roughness analysis in high-speed drilling of unreinforced and reinforced polyamides
V. N. Gaitonde et al.
JOURNAL OF COMPOSITE MATERIALS (2012)
Experimental Investigations on Some Aspects of Machinability in Drilling of Glass Epoxy Polymer Composites
S. Basavarajappa et al.
JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2012)
Experimental investigation and optimisation in drilling of GFRP composites
K. Palanikumar
MEASUREMENT (2011)
Behavior of Sandwich Beams With Functionally Graded Rubber Core in Three Point Bending
M. R. Doddamani et al.
POLYMER COMPOSITES (2011)
Machinability analysis in drilling woven GFR/epoxy composites: Part I - Effect of machining parameters
U. A. Khashaba et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Delamination in high speed drilling of carbon fiber reinforced plastic (CFRP)
Juan C. Campos Rubio et al.
JOURNAL OF COMPOSITE MATERIALS (2008)
Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites
V. N. Gaitonde et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Experimental study of drilling composite materials with step-core drill
C. C. Tsao
MATERIALS & DESIGN (2008)
Development of artificial neural network models to study the effect of process parameters on burr size in drilling
S. R. Karnik et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2008)
Assessment of factors influencing surface roughness on the machining of Al/SiC particulate composites
K. Palanikumar et al.
MATERIALS & DESIGN (2007)
Factors affecting the machinability of GFR/epoxy composites
I El-Sonbaty et al.
COMPOSITE STRUCTURES (2004)
Workpiece damping and its effect on delamination damage in drilling thin composite laminates
E Capello
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Share Paper
