Related references
Note: Only part of the references are listed.A novel approach for dynamic compaction of Mg-SiC nanocomposite powder using a modified Split Hopkinson Pressure Bar
K. Rahmani et al.
POWDER METALLURGY (2018)
Temperature effect on mechanical and tribological characterization of Mg-SiC nanocomposite fabricated by high rate compaction
G. H. Majzoobi et al.
MATERIALS RESEARCH EXPRESS (2018)
Investigation of deep rolling effects on the fatigue life of Al-SiC nanocomposite
Sajjad Sattari et al.
MATERIALS RESEARCH EXPRESS (2018)
High temperature tensile behavior and microstructure of Al-SiC nanocomposite fabricated by mechanical milling and hot extrusion technique
Mohammadreza Soltani et al.
MATERIALS RESEARCH EXPRESS (2018)
Effects of the deep rolling process on the surface roughness and properties of an Al-3vol%SiC nanoparticle nanocomposite fabricated by mechanical milling and hot extrusion
Sajjad Sattari et al.
INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2017)
Mechanical and microstructural investigation of Zn/Sn multilayered composites fabricated by accumulative roll bonding (ARB) process
Amir Mashhadi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Evaluation of tensile strength of Al7075-SiC nanocomposite compacted by gas gun using spherical indentation test and neural networks
A. Atrian et al.
ADVANCED POWDER TECHNOLOGY (2016)
A comparative study on hot dynamic compaction and quasi-static hot pressing of Al7075/SiCnp nanocomposite
A. Atrian et al.
ADVANCED POWDER TECHNOLOGY (2015)
Tribological properties of Al7075-SiC nanocomposite prepared by hot dynamic compaction
G. H. Majzoobi et al.
COMPOSITE INTERFACES (2015)
The inducement of residual stress through deep rolling of AISI 1060 steel and its subsequent relaxation under cyclic loading
A. M. Abrao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Contact mechanics of fractal surfaces by spline assisted discretisation
Dorian A. H. Hanaor et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2015)
Effect of densification rate on consolidation and properties of Al7075-B4C composite powder
G. H. Majzoobi et al.
POWDER METALLURGY (2015)
Finite element approach toward an advanced understanding of deep rolling induced residual stresses, and an application to railway axles
S. M. Hassani-Gangaraj et al.
MATERIALS & DESIGN (2015)
Investigating the surface quality of the burnished brass C3605-fuzzy rule-based approach
Ahmed A. D. Sarhan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Mechanical and microstructural characterization of Al7075/SiC nanocomposites fabricated by dynamic compaction
A. Atrian et al.
INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2014)
Experimental parameter sensitivity analysis of residual stresses induced by deep rolling on 7075-T6 aluminium alloy
M. Beghini et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Surface and subsurface alterations induced by deep rolling of hardened AISI 1060 steel
A. M. Abrao et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2014)
Powder metallurgical components: Improvement of surface integrity by deep rolling and case hardening
P. Nusskern et al.
2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) (2014)
The influence of deep rolling on the surface integrity of AISI 1060 high carbon steel
A. M. Abrao et al.
2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) (2014)
Finite element analysis of ball burnishing process: comparisons between numerical results and experiments
M. Sayahi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Cutting force reduction and surface quality improvement in machining of aerospace duralumin AL-2017-T4 using carbon onion nanolubrication system
M. Sayuti et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
An investigation of the mechanics of roller burnishing through finite element simulation and experiments
Pascale Balland et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)
Surface Defect Generation and Recovery in Cold Rolling of Stainless Steel Strips
E. Mancini et al.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2011)
Finite element analysis of the roller burnishing process for fatigue resistance increase of engine components
F. Klocke et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2011)
A Review of Fatigue Behavior in Nanocrystalline Metals
H. A. Padilla et al.
EXPERIMENTAL MECHANICS (2010)
Finite element modeling of hard roller burnishing: An analysis on the effects of process parameters upon surface finish and residual stresses
Partchapol Sartkulvanich et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2007)
Effective boundary of deep-rolling treatment and its correlation with residual stress stability of Al-Mg-Mn and Al-Mg-Si-Cu alloys
P. Juijerm et al.
SCRIPTA MATERIALIA (2007)
Effect of high-temperature deep rolling on cyclic deformation behavior of solution-heat-treated Al-Mg-Si-Cu alloy
P. Juijerm et al.
SCRIPTA MATERIALIA (2007)
Finite element modeling of roller burnishing process
YC Yen et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2005)
The effect of roll roughness on the rolling parameters during cold rolling of an aluminum alloy
JG Lenard
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Share Paper
