Related references
Note: Only part of the references are listed.Experimental investigation and modelling of drilling on multi-wall carbon nanotube-embedded epoxy/glass fabric polymeric nanocomposites
Kalyan Kumar Singh et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2018)
Role of the surface quality on the mechanical behavior of CFRP bolted composite joints
M. Saleem et al.
INTERNATIONAL JOURNAL OF FATIGUE (2015)
Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite
Nicolas Cadorin et al.
WEAR (2015)
An approach towards damage free machining of CFRP and GFRP composite material: a review
Dhiraj Kumar et al.
ADVANCED COMPOSITE MATERIALS (2015)
Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid
N. Cadorin et al.
JOURNAL OF COMPOSITE MATERIALS (2015)
Study of trimming damages of CFRP structures in function of the machining processes and their impact on the mechanical behavior
M. Haddad et al.
COMPOSITES PART B-ENGINEERING (2014)
Investigating the effect of machining processes on the mechanical behavior of composite plates with circular holes
M. Saleem et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
Parametric study of CO2 laser drilling of carbon nanopowder/vinylester/glass nanocomposites using design of experiments and grey relational analysis
S. Nagesh et al.
OPTICS AND LASER TECHNOLOGY (2013)
Experimental evaluation of laser cut quality of glass fibre reinforced plastic composite
I. A. Choudhury et al.
OPTICS AND LASERS IN ENGINEERING (2013)
Fibre laser cutting of carbon fibre-reinforced polymeric composites
Reza Negarestani et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2013)
Tribo-functional design of double cone drill implications in tool wear during drilling of copper mesh/CFRP/woven ply
Redouane Zitoune et al.
WEAR (2013)
Experimental study on the CO2 laser cutting of carbon fiber reinforced plastic composite
A. Riveiro et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates
Vijayan Krishnaraj et al.
COMPOSITES PART B-ENGINEERING (2012)
A study on UV laser drilling of PEEK reinforced with carbon fibers
L. Romoli et al.
OPTICS AND LASERS IN ENGINEERING (2012)
Study on UV laser machining quality of carbon fibre reinforced composites
Z. L. Li et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Laser cutting of polymeric materials: An experimental investigation
I. A. Choudhury et al.
OPTICS AND LASER TECHNOLOGY (2010)
Design and Test of a Multitooth Tool for CFRP Milling
L. N. Lopez De lacalle et al.
JOURNAL OF COMPOSITE MATERIALS (2009)
Some experimental studies on CO2 laser cutting quality of polymeric materials
J. Paulo Davim et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Drilling of fiber reinforced plastics: A review
A. M. Abrao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Fabrication and evaluation of carbon nano fiber filled carbon/epoxy composite
Yuanxin Zhou et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Cutting of 1.2 mm thick austenitic stainless steel sheet using pulsed and CWNd:YAG laser
KA Ghany et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Laser cutting of different polymeric plastics (PE, PP and PC) by a CO2 laser beam
F Caiazzo et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Experimental and theoretical analyses of cutting nonmetallic materials by low power CO2-laser
BH Zhou et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Laser processing of plastics
B Rooks
INDUSTRIAL ROBOT-AN INTERNATIONAL JOURNAL (2004)
A study of the heat-affected zone in the UVYAG laser drilling of GFRP materials
KC Yung et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
CO2 laser cutting of MDF 1.: Determination of process parameter settings
KCP Lum et al.
OPTICS AND LASER TECHNOLOGY (2000)
Share Paper
