Related references
Note: Only part of the references are listed.Influence of mechanical properties of polypropylene/low-density polyethylene nanocomposites: Compatibility and crystallization
Bei Su et al.
NANOMATERIALS AND NANOTECHNOLOGY (2017)
Experimental and theoretical studies on the properties of injection moulded glass fibre reinforced mixed plastics composites
Rohan Muni Bajracharya et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Coupled influence of strain rate and heterogeneous fibre orientation on the mechanical behaviour of short-glass-fibre reinforced polypropylene
D. Notta-Cuvier et al.
MECHANICS OF MATERIALS (2016)
Effects of fiber orientation and anisotropy on tensile strength and elastic modulus of short fiber reinforced polymer composites
Seyyedvahid Mortazavian et al.
COMPOSITES PART B-ENGINEERING (2015)
Novel foaming method to fabricate microcellular injection molded polycarbonate parts using sodium chloride and active carbon as nucleating agents
Jun Peng et al.
POLYMER ENGINEERING AND SCIENCE (2015)
A model for fiber length attrition in injection-molded long-fiber composites
Jay H. Phelps et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
Pressurized Water Pellets and Supercritical Nitrogen in Injection Molding
Eusebio Duarte Cabrera et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2013)
Shear induced fiber orientation, fiber breakage and matrix molecular orientation in long glass fiber reinforced polypropylene composites
Jianchuan Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Extrusion foaming of polystyrene/carbon particles using carbon dioxide and water as co-blowing agents
Cailiang Zhang et al.
POLYMER (2011)
Correlation Between Processing Conditions and Fiber Breakage During Compounding of Glass Fiber-Reinforced Polyamide
Funda Inceoglu et al.
POLYMER COMPOSITES (2011)
Characterization of fatigue behavior of long fiber reinforced thermoplastic (LFT) composites
A. Goel et al.
MATERIALS CHARACTERIZATION (2009)
Mechanical properties of injection molded long fiber polypropylene composites, part 2: Impact and fracture toughness
K. Senthil Kumar et al.
POLYMER COMPOSITES (2008)
Mechanical properties of injection molded long fiber polypropylene composites, part 1: Tensile and flexural properties
K. Senthil Kumar et al.
POLYMER COMPOSITES (2007)
Shear enhanced fiber orientation and adhesion in PP/glass fiber composites
M Guo et al.
MACROMOLECULAR MATERIALS AND ENGINEERING (2006)
The effect of molecular weight on the interfacial properties of GF/PP injection molded composites
T. Yoshida et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)
Reduced fibre breakage in a glass-fibre reinforced thermoplastic through foaming
G Zhang et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2005)
Effects of the chemical foaming agents, injection parameters, and melt-flow index on the microstructure and mechanical properties of microcellular injection-molded wood-fiber/polypropylene composites
AK Bledzki et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2005)
Injection molding of long sisal fiber-reinforced polypropylene:: Effects of compatibilizer concentration and viscosity on fiber adhesion and thermal degradation
LM Arzondo et al.
POLYMER ENGINEERING AND SCIENCE (2005)
Effects of processing conditions on the fiber length distribution and mechanical properties of glass fiber reinforced nylon-6
U Yilmazer et al.
POLYMER COMPOSITES (2002)
The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene: 5. Injection moulded long and short fibre PP
JL Thomason
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2002)
Numerical simulation for thin wall injection molding of fiber reinforced thermoplastics
YK Shen et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2001)
The characterization of low cost fiber reinforced thermoplastic composites produced by the DRIFT (TM) process
T Hartness et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2001)