Related references
Note: Only part of the references are listed.Fatigue life estimation in presence of ratcheting phenomenon for AISI 304LN stainless steel tested under uniaxial cyclic loading
Srimant Kumar Mishra et al.
INTERNATIONAL JOURNAL OF DAMAGE MECHANICS (2016)
Ratcheting prediction of Al 6061/SiCP composite samples under asymmetric stress cycles by means of the Ahmadzadeh-Varvani hardening rule
G. R. Ahmadzadeh et al.
JOURNAL OF COMPOSITE MATERIALS (2016)
Creep-fatigue behaviour of aluminum alloy-based metal matrix composite
Daniele Barbera et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2016)
Impression creep behaviour of squeeze-cast Ca and Sb added AZ91 magnesium alloy
A. K. S. Bankoti et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Influence of casting defect and SDAS on the multiaxial fatigue behaviour of A356-T6 alloy including mean stress effect
Mohamed Iben Houria et al.
INTERNATIONAL JOURNAL OF FATIGUE (2015)
Influence of Heat Treatment on Ratcheting Fatigue Behavior and Post Ratcheting Tensile Properties of Commercial Aluminum
R. Kreethi et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2015)
Impression creep behavior of Al-1.9%Ni-1.6%Mn-1%Mg alloy
S. M. Miresmaeili et al.
MATERIALS & DESIGN (2014)
Impression test-A review
Fuqian Yang et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2013)
Alloy Composition and Dendrite Arm Spacing in Al-Si-Cu-Mg-Fe Alloys
Tharmalingam Sivarupan et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Effect of Mg and semi solid processing on microstructure and impression creep properties of A356 alloy
B. Amir Esgandari et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2013)
Ratcheting phenomenon and post-ratcheting tensile behaviour of an aluminum alloy
Krishna Dutta et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Uniaxial Ratcheting Behaviors of Metals with Different Crystal Structures or Values of Fault Energy: Macroscopic Experiments
Guozheng Kang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2011)
Creep in nanocrystalline materials: Role of stress assisted grain growth
S. Gollapudi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Effect of Ca and Rare Earth Elements on Impression Creep Properties of AZ91 Magnesium Alloy
B. Nami et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)
Effect of casting imperfections on the fatigue life of 319-F and A356-T6 Al-Si casting alloys
H. R. Ammar et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Uniaxial time-dependent ratchetting of SiCP/6061Al composites at room and high temperature
Guozheng Kang
COMPOSITES SCIENCE AND TECHNOLOGY (2006)
Impression creep technique - An overview
DH Sastry
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Effect of friction stir processing on fatigue behavior of A356 alloy
SR Sharma et al.
SCRIPTA MATERIALIA (2004)
Share Paper
