Related references
Note: Only part of the references are listed.Automatic identification of feed marks in machined surface roughness profiles by correlating random variations
Paul R. Provencher et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Influence of cutting parameters on work hardening behavior of surface layer during turning superalloy Inconel 718
Xiaoping Ren et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Evaluation of Response Surface Designs in Presence of Errors in Factor Levels
Juntao Fang et al.
COMMUNICATIONS IN STATISTICS-THEORY AND METHODS (2015)
Study on surface defects in milling Inconel 718 super alloy
Liu Chang et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2015)
High Speed Turning of Inconel 718 Using Ceramic and Carbide Cutting Tools
S. Amini et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2014)
Improving surface integrity in finish machining of Inconel 718 alloy using intelligent systems
Farshid Jafarian et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Analysis of subsurface microstructure and residual stresses in machined Inconel 718 with PCBN and Al2O3-SiCw tools
Jinming Zhou et al.
2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) (2014)
Empirical modeling of residual stress profile in machining nickel-based superalloys using the sinusoidal decay function
D. Ulutan et al.
2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) (2014)
Microstructural characteristics of forged and heat treated Inconel-718 disks
A. Chamanfar et al.
MATERIALS & DESIGN (2013)
An investigation of surface damage in the high speed turning of Inconel 718 with use of whisker reinforced ceramic tools
J. M. Zhou et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)
Investigation on Machining Performance of Inconel 718 under High Pressure Cooling Conditions
Oguz Colak
STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING (2012)
Identification of Subsurface Deformation in Machining of Inconel 718
Jinming Zhou et al.
MATERIALS AND COMPUTATIONAL MECHANICS, PTS 1-3 (2012)
Effect of cutting parameters on cutting force and surface roughness during finish hard turning AISI52100 grade steel
Gaurav Bartarya et al.
FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)
Multi-objective optimization of surface roughness and cutting forces in high-speed turning of Inconel 718 using Taguchi grey relational analysis (TGRA)
Raju Shrihari Pawade et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Machining induced surface integrity in titanium and nickel alloys: A review
Durul Ulutan et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2011)
Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718
R. S. Pawade et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Study of standard heat treatment on mechanical properties of Inconel 718 using ball indentation technique
Sabita Ghosh et al.
MATERIALS LETTERS (2008)
An investigation of cutting forces and surface damage in high-speed turning of Inconel 718
R. S. Pawade et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
High temperature deformation of Inconel 718
A. Thomas et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2006)
Optimum surface roughness in end milling Inconel 718 by coupling neural network model and genetic algorithm
B Ozcelik et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2005)
Some effects of cutting edge preparation and geometric modifications when turning INCONEL 718™ at high cutting speeds
RT Coelho et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Workpiece surface integrity and tool life issues when turning Inconel 718™ nickel based superalloy
ARC Sharman et al.
MACHINING SCIENCE AND TECHNOLOGY (2004)
Effect of standard heat treatment on the microstructure and mechanical properties of hot isostatically pressed superalloy inconel 718
GA Rao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
An overview of the machinability of aeroengine alloys
EO Ezugwu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)