Related references
Note: Only part of the references are listed.Numerical simulation of thermal fatigue behavior in a cracked disc of AISI H-11 tool steel
Faisal Qayyum et al.
ENGINEERING FAILURE ANALYSIS (2016)
Generation of electrical energy using lead zirconate titanate (PZT-5A) piezoelectric material: Analytical, numerical and experimental verifications
Zubair Butt et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2016)
Fatigue analysis on offshore pipelines with embedded cracks
Y. M. Zhang et al.
OCEAN ENGINEERING (2016)
The effect of anisotropy on the intermediate and final form in deep drawing of SS304L, with high draw ratios: Experimentation and numerical simulation
F. Qayyum et al.
14TH INTERNATIONAL SYMPOSIUM ON ADVANCED MATERIALS (ISAM 2015) (2016)
Investigation of mechanical properties based on grain growth and microstructure evolution of alumina ceramics during two step sintering process
U. A. Khan et al.
14TH INTERNATIONAL SYMPOSIUM ON ADVANCED MATERIALS (ISAM 2015) (2016)
Numerical Simulation and Experimental Verification of CMOD in CT Specimens of TIG Welded AA2219-T87
Mudaser Ullah et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2015)
Lay-up optimisation of fibre metal laminates based on fatigue crack propagation and residual strength
I. Sen et al.
COMPOSITE STRUCTURES (2015)
Prediction of non-propagating fretting fatigue cracks in Ti6Al4V sheet tested under pin-in-dovetail configuration: Experimentation and numerical simulation
Zeeshan Anjum et al.
MATERIALS & DESIGN (2015)
Low-cycle fatigue delamination initiation and propagation in fibre metal laminates
F. Mazaheri et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2015)
Crack growth resistance curves of GLARE 3 5/4 0.3 fiber-metal laminates at low temperature
O. H. Paiva Martins Fontes et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2015)
Comparison of thermomechanical stresses produced in work rolls during hot and cold rolling of Cartridge Brass 1101
F. Qayyum et al.
MATERIALS SCIENCE AND TECHNOLOGY (2015)
Optimization of interlaminar shear strength behavior of anodized and unanodized ARALL composites fabricated through VARTM process
Haroon Qaiser et al.
INTERNATIONAL JOURNAL OF MATERIAL FORMING (2015)
Determination of fracture toughness J on fiber-metal laminate type CARALL with sheets of aluminium 6061
Juan C. Rios et al.
INTERNATIONAL CONGRESS OF SCIENCE AND TECHNOLOGY OF METALLURGY AND MATERIALS, SAM - CONAMET 2014 (2015)
Interface analysis of fiber metal laminates
Monika Ostapiuk et al.
COMPOSITE INTERFACES (2014)
A novel process for cost effective manufacturing of fiber metal laminate with textile reinforced pCBT composites and aluminum alloy
Wangqing Wu et al.
COMPOSITE STRUCTURES (2014)
Computational Investigation of Glare with Several Cracks and Delaminations under Monotonic and Cyclic Loads of Constant Amplitude
Sunil Bhat et al.
MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2014)
Fatigue crack growth in fiber-metal laminates
Ma YuE et al.
SCIENCE CHINA-PHYSICS MECHANICS & ASTRONOMY (2014)
High-cycle fatigue investigations of notched Glare under different stress ratio's in various environments
Sunil Bhat et al.
INTERNATIONAL JOURNAL OF MECHANICAL AND MATERIALS ENGINEERING (2014)
Effect of internal fluid pressure on quality of aluminum alloy tube in rotary draw bending
Lucian Lazarescu
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Numerical Simulation and Experimental Verification of CMOD in SENT Specimen: Application on FCGR of Welded Tool Steel
Amir Sultan et al.
ACTA METALLURGICA SINICA-ENGLISH LETTERS (2013)
Fatigue damage development in new fibre metal laminates made by the VARTM process
E. K. Baumert et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2011)
A review: Fibre metal laminates, background, bonding types and applied test methods
Tamer Sinmazcelik et al.
MATERIALS & DESIGN (2011)
Experimental characterization of the crack-tip-opening angle in fibre metal laminates
Riccardo Rodi et al.
ENGINEERING FRACTURE MECHANICS (2010)
Delamination growth in Fibre Metal Laminates under variable amplitude loading
S. U. Khan et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2009)
Fatigue crack growth in fibre metal laminates under selective variable-amplitude loading
H. M. Plokker et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2009)
The meaning of threshold fatigue in fibre metal laminates
Rene Alderliesten et al.
INTERNATIONAL JOURNAL OF FATIGUE (2009)
Fatigue crack growth in hybrid boron/glass/aluminium fibre metal laminates
P. -Y. Chang et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2008)
Modeling of fatigue crack growth in notched fiber metal laminates
Po-Yu Chang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2008)
Progressive delamination with and without crack propagation in aramid fiber reinforced metal laminates containing a circular notch
Cheol Woong Kim et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Off-axis fatigue cracking behaviour in notched fibre metal laminates
P. -Y. Chang et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2007)
Analytical prediction model for fatigue crack propagation and delamination growth in Glare
R. C. Alderliesten
INTERNATIONAL JOURNAL OF FATIGUE (2007)
Progressive damage modeling in fiber-reinforced materials
Ireneusz Lapczyk et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2007)
Fatigue and damage tolerance issues of Glare in aircraft structures
R. C. Alderliesten et al.
INTERNATIONAL JOURNAL OF FATIGUE (2006)
Fatigue initiation in fibre metal laminates
JJ Homan
INTERNATIONAL JOURNAL OF FATIGUE (2006)
The fracture properties of a fibre-metal laminate based on magnesium alloy
P Cortes et al.
COMPOSITES PART B-ENGINEERING (2006)
Avoiding knife-edge countersinks in GLARE through dimpling
C Rans et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2005)
Residual strength of unidirectional fibre-metal laminates based on Jc toughness of C(T) and SE(B) specimens:: comparison with M(T) test results
EM Castrodeza et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2004)
Fatigue crack growth prediction in GLARE hybrid laminates
DJ Shim et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2003)
Development of fibre metal laminates for advanced aerospace structures
LB Vogelesang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
On the fracture mechanical behaviour of fibre reinforced metal laminates (FRMLs)
A Afaghi-Khatibi et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2000)
Share Paper
