Related references
Note: Only part of the references are listed.Plasma immersion ion implantation and shot peening influence on the fatigue strength of AA 7050-T7451 aluminum alloy
Yara Coelho Bastos et al.
ENGINEERING RESEARCH EXPRESS (2020)
Investigation of residual stress, stress relaxation and work hardening effects induced by shot peening on the fatigue life of AA 6005-T6 aluminum alloy
Martin Ferreira Fernandes et al.
MATERIALS RESEARCH EXPRESS (2019)
Mechanical and Tribological Properties of Shot-Peened SAE 1070 Steel
N. W. Khun et al.
TRIBOLOGY TRANSACTIONS (2016)
Mechanical and Tribological Properties of Spark Plasma-Sintered Titanium Composites Filled with Different Al-Cr-Fe Quasicrystal Contents
N. W. Khun et al.
TRIBOLOGY TRANSACTIONS (2015)
Effects of Al-Cr-Fe Quasicrystal Content on Tribological Properties of Cold-Sprayed Titanium Composite Coatings
N. W. Khun et al.
TRIBOLOGY TRANSACTIONS (2015)
Effects of deep cryogenic treatment on mechanical and tribological properties of AISI D3 tool steel
Nay Win Khun et al.
FRICTION (2015)
Novel Ti based metal matrix composites reinforced with Al-Cr-Fe quasicrystals approximants
R. T. Li et al.
MATERIALS SCIENCE AND TECHNOLOGY (2015)
Corrosion Analysis of Friction Stir-welded AA 7075 Aluminium Alloy
Govindaraj Elatharasan et al.
STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING (2014)
Effects of Normal Load, Sliding Speed, and Surface Roughness on Tribological Properties of Niobium under Dry and Wet Conditions
N. W. Khun et al.
TRIBOLOGY TRANSACTIONS (2014)
Surface Finish and Residual Stresses Induced by Orthogonal Dry Machining of AA7075-T651
Walid Jomaa et al.
MATERIALS (2014)
Surface roughness optimization of cold-sprayed coatings using Taguchi method
Tarun Goyal et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Surface Layer Characteristics of S30432 Austenite Stainless Steel after Shot Peening
K. Zhan et al.
MATERIALS TRANSACTIONS (2012)
Lubrication and wear modelling of artificial hip joints: A review
L. Mattei et al.
TRIBOLOGY INTERNATIONAL (2011)
Tribological Effects of Mineral-Oil Lubricant Contamination with Biofuels: A Pin-on-Disk Tribometry and Wear Study
S. M. Shanta et al.
ADVANCES IN TRIBOLOGY (2011)
Experimental study of shot peening and stress peen forming
H. Y. Miao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)
The effects of laser peening and shot peening on high cycle fatigue in 7050-T7451 aluminum alloy
Harold Luong et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Influence of surface texture and roughness parameters on friction and transfer layer formation during sliding of aluminium pin on steel plate
Pradeep L. Menezes et al.
WEAR (2009)
Effect of wear of bearing surfaces on elastohydrodynamic lubrication of metal-on-metal hip implants
F Liu et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART H-JOURNAL OF ENGINEERING IN MEDICINE (2005)
The influence of surface roughness on friction and wear of machine element coatings
F Svahn et al.
WEAR (2003)
The relationship between hardness and abrasive wear resistance of electrodeposited nanocrystalline Ni-P coatings
DH Jeong et al.
SCRIPTA MATERIALIA (2003)
Share Paper
