Related references
Note: Only part of the references are listed.A simple method for assessing powder spreadability for additive manufacturing
Moustafa Ahmed et al.
POWDER TECHNOLOGY (2020)
Atomization simulation and preparation of 24CrNiMoY alloy steel powder using VIGA technology at high gas pressure
Mingwei Wei et al.
POWDER TECHNOLOGY (2020)
Thermodynamic conditions for cluster formation in supersaturated boundary layer during plasma spray-physical vapor deposition
Mei-Jun Liu et al.
APPLIED SURFACE SCIENCE (2019)
Preparation and characterization of spherical niobium silicide-based powder particles by electrode induction gas atomization
Jong Min Park et al.
MATERIALS LETTERS (2019)
Effect of hot isostatic pressing (HIP) on microstructure and mechanical properties of Ti6Al4V alloy fabricated by cold spray additive manufacturing
Chaoyue Chen et al.
ADDITIVE MANUFACTURING (2019)
Microstructure evolution of the rapidly solidified alloy powders and composite powders
Q. Yang et al.
MATERIALS & DESIGN (2019)
Characteristics and printability of K417G nickel-base alloy powder prepared by VIGA method
Wuming Jia et al.
POWDER METALLURGY (2019)
A numerical simulation study of the path-resolved breakup behaviors of molten metal in high-pressure gas atomization: With emphasis on the role of shock waves in the gas/molten metal interaction
Rashed Kaiser et al.
ADVANCED POWDER TECHNOLOGY (2018)
Preparation and characterization of 316L spherical powder for different uses by supersonic laminar flow atomization
Shengsheng Yu et al.
FERROELECTRICS (2018)
Influence of Powder Characteristics on Processability of AlSi12 Alloy Fabricated by Selective Laser Melting
Rustam Baitimerov et al.
MATERIALS (2018)
Computational fluid dynamic investigation of the primary and secondary atomization of the free-fall atomizer in electrode induction melting gas atomization process
Xia Min et al.
ACTA PHYSICA SINICA (2018)
Process modeling pressure-swirl-gas-atomization for metal powder production
Xing-gang Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Effect of atomization pressure on the breakup of TA15 titanium alloy powder prepared by EIGA method for laser 3D printing
Mingwei Wei et al.
VACUUM (2017)
NUMERICAL MODELING AND PREDICTION OF PARTICLE SIZE DISTRIBUTION DURING GAS ATOMIZATION OF MOLTEN TIN
S. Sarkar et al.
ATOMIZATION AND SPRAYS (2016)
Influence of density ratio on the secondary atomization of liquid droplets under highly unstable conditions
Wei Yang et al.
FUEL (2016)
Predicting droplet deformation and breakup for moderate Weber numbers
George Strotos et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2016)
Quantification and characterisation of porosity in selectively laser melted Al-Si10-Mg using X-ray computed tomography
I. Maskery et al.
MATERIALS CHARACTERIZATION (2016)
The identification of an accurate simulation approach to predict the effect of operational parameters on the particle size distribution (PSD) of powders produced by an industrial close-coupled gas atomiser
J. S. Thompson et al.
POWDER TECHNOLOGY (2016)
Accurate level set method for simulations of liquid atomization
Changxiao Shao et al.
CHINESE JOURNAL OF CHEMICAL ENGINEERING (2015)
A coupled level-set and volume-of-fluid simulation for splashing of single droplet impact on an inclined liquid film
Dai Jian-Feng et al.
ACTA PHYSICA SINICA (2015)
LARGE EDDY SIMULATION OF SINGLE DROPLET AND LIQUID JET PRIMARY BREAKUP USING A COUPLED LEVEL SET/VOLUME OF FLUID METHOD
F. Xiao et al.
ATOMIZATION AND SPRAYS (2014)
Metal Additive Manufacturing: A Review
William E. Frazier
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Evaluation of the splats properties and relation with droplets diameters in atomization process using a De Laval Nozzle
Marie-Pierre Planche et al.
MATERIALS CHEMISTRY AND PHYSICS (2013)
Thermophysical properties of Alloy 617 from 25 degrees C to 1000 degrees C
B. H. Rabin et al.
NUCLEAR ENGINEERING AND DESIGN (2013)
Laser additive manufacturing of metallic components: materials, processes and mechanisms
D. D. Gu et al.
INTERNATIONAL MATERIALS REVIEWS (2012)
Processing parameter effect on the splat diameters of the droplets produced by liquid metal atomization using De Laval nozzle
O. Khatim et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Secondary atomization
D. R. Guildenbecher et al.
EXPERIMENTS IN FLUIDS (2009)
Progress in gas atomization of liquid metals by means of a De Laval nozzle
A. Allimant et al.
POWDER TECHNOLOGY (2009)
Spatial instability of a viscous liquid sheet
SG Chuech
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS (2006)
A computational fluid dynamics (CFD) investigation of the wake closure phenomenon
J Ting et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Temporal properties of secondary drop breakup in the multimode breakup regime
Z Dai et al.
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2001)
Share Paper
